AD1650B MicroPower EP Video Matrix Switching System Installation Instructions This manual describes the installation procedures for the American Dynamics model AD1650B MicroPower EP Video Matrix Switching Systems. The AD1650B is a CCTV surveillance control system having multiple video inputs, multiple video outputs, and multiple control stations.
The software/firmware furnished with this equipment is confidential to and is copyrighted by AMERICAN DYNAMICS. It is not to be copied or disclosed in any manner without the express written consent of AMERICAN DYNAMICS. The software/firmware is furnished to the purchaser under a license for use on a single system. Note: Information furnished by AMERICAN DYNAMICS is believed to be accurate and reliable.
AMERICAN DYNAMICS The installation of this product should be made by qualified service personnel and should conform to all local codes. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CONTENTS Page SYSTEM DESCRIPTION................................................................................ 1 MODULE DESCRIPTIONS ............................................................................ 2 SETUP Central Processing Module...................................................................... 1-2 Video Input Module................................................................................. 1-2 Video Output Module ....................................................................
AD1650B SYSTEM DESCRIPTION SYSTEM DESCRIPTION System Keyboards The AD1650B MicroPower EP Matrix Switching System is a CCTV control system with multiple video inputs, multiple video outputs, and multiple control stations. The AD1650B is capable of controlling a maximum of 128 video input sources such as cameras, a maximum of 16 video outputs such as monitors, and a maximum of 24 keyboards. Eight 2-wire keyboard ports are provided on the rear panel of the Central Processing Module.
MODULE DESCRIPTIONS AD1650B SYSTEM MODULE DESCRIPTIONS Central Processing Module - AD1661B Power Supply Module - AD1603N The AD1661B Central Processing Module (CPM) controls the switching bays for the AD1650B system and provides the onscreen programming menus for setup of the system (see System Programming Manual, OP1650BSPB). The AD1661 CPM rear panel provides eight 2-wire keyboard input ports and a programming monitor video output BNC connector, labeled PROG MON, as shown below.
AD1650B MODULE DESCRIPTIONS Terminating Video Input Module - AD1611 Video Output Module - AD1626 The AD1611 Video Input Module (VIM) performs the actual video switching in the AD1650B switching bays. Each module can switch any one of eight video inputs to any video output, or multiple combinations of video outputs, up to eight. The eight video inputs to the module are connected at the rear panel BNC connectors, as shown below.
SETUP This section of the manual describes the module setup procedures for the AD1650B System. All AD1650B systems are factory configured for proper operation. However, it may be necessary to change or adjust the factory setups to certain modules for unique or changing user requirements. Certain of these module setup procedures should be made prior to installation and connection of the AD1650B (Section 2).
SETUP AD1650B SETUP Video Output Module - Monitor Selection ! CAUTION - Due to the presence of noninsulated components with hazardous voltages, the following internal adjustments should be performed by qualified service personnel only. The AD1626 VOMs are properly configured at the factory. In the event a module setup must be changed, the module must be configured before installation and connection of video outputs. This is done with the AD1626 VOM removed from the bay.
AD1650B SETUP Power Supply Module Power Supply Module - Fuse replacement The AD1603N Power Supply Module converts the input AC power to the necessary DC voltages which are supplied to all the modules in the AD1650B bay. The AD1603N PSM also includes the Control Code circuitry which supplies code to the remote Receivers and other Control Code accessories. The Power Supply Module contains four fuses for the input AC power to the AD1603N and the output DC power from the AD1603N to the AD1650B modules.
SYSTEM INSTALLATION This section of the manual describes the system installation and connection procedures for the AD1650B System. AD1650B Systems are supplied in completely configured switching bays. Only the necessary bay interconnections, the video input and output connections, and any optional accessory connections need be made prior to operation. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYSTEM INSTALLATION AD1650B INSTALLATION CONNECTIONS This installation should be made by qualified service personnel and should conform to all local codes. Safeguards must be taken to avoid unintentional operation by employees and maintenance personnel working about the premises, by falling objects, by customers, by building vibration, and by similar causes. Mounting AD1650B systems are normally supplied for standard 19-inch rack mounting and have a rack height of 5 1/4 inches.
AD1650B SYSTEM INSTALLATION Control Code Connections * The Control Code for Receivers, Code Followers/Responders, Code Distributors, Code Translators, and other code-controlled accessories is provided by Control Code Outputs in either the AD1651B, AD1653B, or AD1655 bay. Accessories associated with video inputs 1 through 64 are controlled by the Control Code Output from AD1651B or AD1653B bays.
SYSTEM INSTALLATION AD1650B PIN 4 PIN 5 System Control Connections TWO-WIRE KEYBOARDS Eight 2-wire keyboard ports are provided on the rear panel of the AD1661B or AD1663B CPM (see rear panel illustrations on page 2). The port number labels on the rear panel, 1 - 8, correspond to the monitor number controlled via that port. Two AD keyboards are available for connection to these ports: The AD1672A is a 2-monitor keyboard.
SYSTEM CONFIGURATIONS The following section of this manual provides interconnection information for typical configurations of the AD1650B system. These are organized according to the size and capabilities of systems. System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Single Bay systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Two Bay systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Three Bay systems . . . . . . . . . .
SYSTEM CONFIGURATIONS AD1650B SYSTEM CONFIGURATIONS The following section of this manual provides interconnection information for typical configurations of the AD1650B system. These are organized according to the size and capabilities of systems, as follows: The descriptions in the following pages include the following subsections of connection instructions, as applicable to each configuration. Power/Data Interconnections 1.
AD1650B SYSTEM CONFIGURATIONS SINGLE BAY SYSTEMS Video Input Connections Single bay systems can consist of 56 cameras and 2 monitors, 48 cameras and 4 monitors, 40 cameras and 6 monitors, or 32 cameras and 8 monitors. A complete system is supplied in one AD1651B bay. Installed modules include: One AD1603N Power Supply Module (PSM), One AD1661B Central Processing Module (CPM), Each AD1611 VIM includes eight terminated BNC’s on the back panel for video input connections.
SYSTEM CONFIGURATIONS AD1650B TWO BAY SYSTEMS, 64 CAMERAS x 8 MONITORS Video Interconnections Systems for a maximum of 64 cameras and 8 monitors are supplied in two bays. The AD1653B bay contains a power supply, processor, and monitor modules for monitors 1 through 8. The AD1654 bay contains the the camera modules for cameras 1 through 64.
AD1650B SYSTEM CONFIGURATIONS THREE BAY SYSTEMS, 128 CAMERAS x 8 MONITORS Video Interconnections Systems for a maximum of 128 cameras and 8 monitors are supplied in three bays. The AD1653B bay contains a power supply, a processor, and monitor modules for monitors 1 through 8. The AD1654 bay contains the camera modules for cameras 1 through 64. The AD1655 bay contains a power supply and camera modules for cameras 65 through 128.
SYSTEM CONFIGURATIONS AD1650B THREE BAY SYSTEMS, 128 CAMERAS x 8 MONITORS (Continued from prior page) Video Input Connections Each AD1611 VIM in the AD1654 and AD1655 bays includes eight terminated BNC’s for video input connections. The system assigns the video input connected to the top BNC on the right-most AD1626 VIM in the AD1654 bay as input number 1. The video input connected to the top BNC on the next VIM to the left is assigned as input number 9 etc., up to video input number 64.
AD1650B SYSTEM CONFIGURATIONS TWO BAY SYSTEMS, 24 CAMERAS x 16 MONITORS Video Input Connections Systems for a maximum of 24 cameras and 16 monitors are supplied in two bays. The AD1653B bay contains a power supply, a processor, camera modules for cameras 1 through 24, and monitor modules for monitors 1 through 8. The AD1657 bay contains a power supply, camera modules for cameras 1 through 24, and monitor modules for monitors 9 through 16.
SYSTEM CONFIGURATIONS AD1650B FOUR BAY SYSTEMS, 64 CAMERAS x 16 MONITORS Video Interconnections Systems for a maximum of 64 cameras and 16 monitors are supplied in four bays. The AD1653B bay contains a power supply, processor, and monitor modules for monitors 1 - 8. The AD1657 bay contains a power supply and monitor modules for monitors 9 - 16. The AD1654 bay contains camera modules for cameras 1 - 64 for monitors 1 - 8. The AD1656 bay contains camera modules for cameras 1 - 64 for monitors 9 - 16.
AD1650B SYSTEM CONFIGURATIONS Video Input Connections Each AD1609CM in the AD1656 bay has eight pairs of looping BNC’s on the back panel for video input connections. Video inputs are connected to one BNC of each pair and looped to the corresponding terminated video input in an AD1611 VIM in the AD1654 bay.
SYSTEM CONFIGURATIONS AD1650B SIX BAY SYSTEMS, 128 CAMERAS x 16 MONITORS Control Code Connections Systems for a maximum of 128 cameras and 16 monitors are supplied in six bays. The AD1653B bay contains a power supply, processor, and monitor modules for monitors 1 through 8; the AD1657 bay contains a power supply and monitor modules for monitors 9 through 16.
AD1650B SYSTEM CONFIGURATIONS Video Interconnections (continued) Video Input Connections AD1654 to AD1653B - Connect the top BNC on the AD1654 bay VIP Panel, labeled 1, to the top input BNC of the AD1653B bay VOM panel for system monitor 1, labeled MONITOR 1 A. Connect the BNC labeled 2 on the AD1654 bay VIP panel, to the top input BNC of the AD1653B bay VOM panel for system monitor 2, labeled 2 A.
OPERATION The following section of this manual describes the powering up and basic operation of the AD1650B system. The complete system setup programming and operating instructions for the AD1650B are provided in the System Programming manual, OP1650BSP. Powering Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Powering the AD1650 bays . . . . . . . . . . . . . . . . . . . . . . 4-2 Operating Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 CPM Reset . .
OPERATION AD1650B POWERING UP A complete AD1650B system may be brought on-line after: Ribbon Cable to DATA OUTPUT PANEL for multiple bay interconnect (1663B CPM models only) • All modules and bays have been installed and connected. • One or more cameras have been connected for video input. • One or more monitors have been connected for viewing video output. Ribbon Cable from POWER SUPPLY for RS-232 Inputs • All video cables have been properly terminated.
AD1650B OPERATION KEYBOARD CONTROL Camera Control The following instructions are for verifying basic operation of the system. For complete setup and programming of the AD1650B, refer to the AD1650B System Programming Manual, OP1650BSPB. Cameras at sites equipped with AD1640 or AD1680 Series Receivers can be controlled by keyboard commands. The following camera control actions are performed on the “Called” camera.
IF YOU ENCOUNTER ANY PROBLEMS OPERATING THIS UNIT, OR NEED ASSISTANCE, CALL OUR TECHNICAL SUPPORT CENTER: within the United States: 1-800-442-2225 outside the United States: (914) 624-7640
TYPICAL SYSTEM CONNECTIONS Typical System Connections AD1672 Keyboard to AD1650B . . . . . . . . . . . . . . . . . . . . . C-2 AD1676 Keyboard to AD1650B . . . . . . . . . . . . . . . . . . . . . C-3 AD2078 Keyboard to AD1650B . . . . . . . . . . . . . . . . . . . . . C-4 AD1691 Code Distributor to AD1650B . . . . . . . . . . . . . . . C-5 AD2096 Alarm Interface to AD1650B . . . . . . . . . . . . C-6, C-7 AD1650B System Configurations Single Bay, 32 Camera, 8 Monitor . . . . . . . . . . . . . . . . . . .
TYPICAL SYSTEM CONNECTIONS AD1672 KEYBOARD TO AD1650B Ð LENS Ð Ð AUX Ð Ð CAMERA SELECT Ð PGM Ð AIM Ð AD1672 MONITOR SELECT SWITCH KEYBOARD CABLE NUMBER 2 KEYBOARD CABLE NUMBER 1 RS-232 PGM MON 1 2 3 4 K E Y B R D 1 2 3 4 J1 OUT 5 6 7 8 AD1650B Connect the cable ground on the cable assembly to one of the four corner screws. CAMERA AND/OR MONITOR MODULES (See TYPICAL CONFIGURATIONS, pages C-8 - C-13) NOTE: THESE CONNECTIONS, ILLUSTRATING CONTROL OF MONITORS 1 AND 2, ARE TYPICAL OF ONE KEYBOARD.
TYPICAL SYSTEM CONNECTIONS AD1676 KEYBOARD TO AD1650B 4 AD1676 3-WIRE, 18 AWG, SHIELDED CABLE, BELDEN 8770 OR EQUIVALENT RCD XMIT 4 5 3 4 6 5 3 HP0047 6 HP0047 2 7 1 8 2 1 GND 7 8 TP8059 JJ0007 JJ0007 RS-232 PGM MON 1 2 3 4 7.5 VOLTS AC 1.5 AMP K E Y B R D 1 2 3 J1 OUT 4 5 6 7 8 AD1650B Connect the cable ground on the cable assembly to one of the four corner screws. NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE KEYBOARD. EACH RS232 PORT IS PROGRAMMABLE.
TYPICAL SYSTEM CONNECTIONS AD2078 KEYBOARD TO AD1650B AD2078 3-WIRE, 18 AWG, SHIELDED CABLE, TO HP0082 TERMINAL BLOCK (J1 SIDE) JUMPER WIRES SUPPLIED WITH KEYBOARD, REMOVE FOR CONNECTIONS OVER 7 FT TO XMIT, PIN 5 TO GND, PIN 7 RCD JJ0007 XMIT 5 4 5 3 6 GND 7 4 4 3 6 TP8082 or TP8083 Wall Transformer TO RCD, PIN 4 2 7 1 8 8 2 6 HP0047 1 J1 5 3 HP0082 TERMINAL BLOCK 2 7 1 8 J2 JJ0007 TO RS232 PORT JJ0007 CONNECTIONS BETWEEN UNITS THAT ARE LESS THAN SEVEN FEET (7') APART
TYPICAL SYSTEM CONNECTIONS AD1691 CODE DISTRIBUTOR TO AD1650B RECEIVER CODE LED W BS B S W J1 AD1691 18 AWG SHIELDED TWISTED PAIR , BELDEN 8760 OR EQUIVALENT S W B AC AC W B S TP8002 12 VOLTS AC 10 VA RS-232 MON 1 2 K E Y B R D 1 2 3 3 J1 OUT 4 5 6 7 8 Connect the cable ground on the cable assembly to one of the four corner screws.
TYPICAL SYSTEM CONNECTIONS AD2096 ALARM INTERFACE TO AD1650B DRAWING ILLUSTRATES CONNECTIONS BETWEEN UNITS THAT ARE GREATER THAN SEVEN FEET (7') APART 1 A 2 A 3 4 A 5 A SELECT 7 A 8 6 A 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 ON OFF PRGM ABCDEFGH POWER 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 43 44 45 46 47 48 ON OFF ALARM ABCDEFGH C O M MW N N C O C M INPUT OUTPUT AD2096 GND JJOOO7 8 HP0047 TERMINAL BOX
TYPICAL SYSTEM CONNECTIONS 2096 ALARM INTERFACE TO 1650B DRAWING ILLUSTRATES CONNECTIONS BETWEEN UNITS THAT ARE LESS THAN SEVEN FEET (7') APART 1 A 2 A SELECT 3 4 A A 7 8 5 A 6 A 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 ON OFF ALARM PRGM ABCDEFGH POWER 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 43 44 45 46 47 48 ON OFF ABCDEFGH C O M MW N N C O C M INPUT OUTPUT AD2096 JJ0007 - FOR CONNECTIONS UP TO 7' RS-232 PG
TYPICAL SYSTEM CONFIGURATIONS SINGLE BAY, 32 Cameras, 8 Monitors PROGRAMMING MONITOR 32 1 8 OUTPUTS TO MONITORS RS-232 PGM MON AD1651 BAY 1 2 3 4 J1 OUT K E Y B R D MONITOR MONITOR 8 6 7 MONITOR 5 4 MONITOR 3 2 1 1 A A A A 2 A A A A 3 B B B B 4 B B B B 5 6 O U T O U T 7 8 O U T O U T O U T O U T O U T O U T C A M E R A C A M E R A C A M E R A C A M E R A 2 5 1 7 9 1 2 8 2 0 1 2 4 2 9 2 1 1 3 5 3 2 2 4 1 6 8 32 INPUTS FROM CAMERAS CONTROL
TYPICAL SYSTEM CONFIGURATIONS TWO BAYS, 64 Cameras, 8 Monitors PROGRAMMING MONITOR 8 OUTPUTS TO MONITORS RS-232 PGM MON 1 2 K E Y B R D MONITOR 8 J2 1 AD1653 BAY 3 2 4 D A T A 3 4 J1 OUT J3 5 6 7 J4 O U T P U T MONITOR 7 6 MONITOR 5 4 MONITOR 3 2 1 1 A A A A A A A A B B B B B B O U T O U T O U T O U T O U T O U T B B 8 8 O U T O U T VIDEO INTERCONNECT FLYING LEADS, FOR CONTROL CODE CONNECTIONS 64 POWER/DATA INTERCONNECT 1 AD1654 BAY V I P C A M E R A
TYPICAL SYSTEM CONFIGURATIONS THREE BAYS, 128 Cameras, 8 Monitors 128 VIDEO INTERCONNECT PANEL 65 V I P AD1655 BAY 1 C A M E R A 1 1 3 C A M E R A 1 0 5 C A M E R A C A M E R A C A M E R A C A M E R A C A M E R A 9 7 8 9 8 1 7 3 6 5 1 2 4 1 2 5 1 1 6 1 1 7 1 0 8 1 0 9 1 0 0 1 0 1 9 2 8 4 7 6 6 8 9 3 8 5 7 7 6 9 1 2 8 1 2 0 1 1 2 1 0 4 9 6 8 8 8 0 7 2 3 4 CONTROL CODE CONNECTIONS, CAMERAS 65-128 C A M E R A 1 2 1 5 7 J1 OUT 2 4 6 8 64 INPUTS FROM CAMERAS VIDEO INT
TYPICAL SYSTEM CONFIGURATIONS TWO BAYS, 24 Cameras, 16 Monitors PROGRAMMING MONITOR 24 LOOPING INPUTS FROM AD1657 BAY 8 OUTPUTS TO MONITORS RS-232 1 2 PGM MON K E Y B R D MONITOR 8 J2 D A T A 1 AD1653 BAY 3 4 2 3 O U T P U T J3 4 J1 OUT 5 6 CONTROL CODE CONNECTIONS J4 MONITOR 7 6 8 4 MONITOR 3 2 1 A A A A A A A A B B B B B B B B O U T O U T 7 MONITOR 5 O U T O U T O U T O U T 8 C A M E R A C A M E R A C A M E R A 1 7 9 1 2 0 1 2 4 2 1 1 3 5
TYPICAL SYSTEM CONFIGURATIONS FOUR BAYS, 64 Cameras, 16 Monitors PROGRAMMING MONITOR 8 OUTPUTS TO MONITORS 1-8 RS-232 1 PGM MON 2 K E Y B R D MONITOR 8 J2 1 AD1653 BAY 2 3 4 3 J3 4 J1 OUT 5 6 J4 D A T A O U T P U T 6 MONITOR 5 4 MONITOR 3 2 1 1 A A A A A A A A B B B B B B B B O U T O U T O U T O U T O U T O U T O U T O U T 8 7 8 FLYING LEADS, FOR CONTROL CODE CONNECTIONS MONITOR 7 VIDEO INTERCONNECT POWER/DATA INTERCONNECT 64 LOOPING INPUTS FROM AD1656 B
4 3 AD1654 BAY J1 OUT FLYING LEADS CONTROL CODE, CAMERAS 1-64 AD1653 BAY 2 1 J1 OUT RS-232 AD1655 BAY J1 OUT 4 8 6 4 2 7 5 3 1 V I P 1 2 8 1 2 4 1 2 5 C A M E R A 1 2 1 8 7 6 5 4 3 2 1 K E Y B R D J4 J3 J2 O U T P U T D A T A 1 2 0 1 1 6 1 1 7 C A M E R A 1 1 3 3 3 O U T O U T B A C A M E R A 1 7 C A M E R A 2 5 9 C A M E R A LOOPED VIDEO INPUTS O U T O U T B B A 2 1 1 MONITOR 4 3 MONITOR 1 C A M E R A O U T O U T B B A A J1 OUT FLYING LE
INDEX
INDEX AD1650B Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AD1603N PSM, Power Supply Module . . . . . . . . . . . . . . . 2 AD1609CM, Video Input Module . . . . . . . . . . . . . . . . . . . 3 AD1611, Video Input Module . . . . . . . . . . . . . . . . . . . . . . 3 AD1626, Video Output Module . . . . . . . . . . . . . . . . . . . . . 3 AD1626NA, Video Output Module . . . . . . . . . . . . . . . . . . 3 AD1661 CPM, Central Processing Module . . . . . . . . . . . .
AD1650B INDEX Three Bays, 128 Camera, 8 Monitor Systems . . . . . . . . . 3-5 Two Bays, 64 Camera, 8 Monitor Systems . . . . . . . . . . . 3-4 Two Bays, 24 Camera, 16 Monitor Systems . . . . . . . . . . 3-7 TYPICAL SYSTEM CONNECTIONS . . . . . . . . . . . . . C-1 Vertical Phase Adjustment, Power Supply Module . . . . . 1-3 Video Input Connections Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Four Bays, 64 Camera, 16 Monitor Systems . . . . . . 3-9 Single Bay Systems . .
Declaration of Conformity Manufacturer: Sensormatic CCTV Systems Division Manufacturer’s Address: Sensormatic CCTV Systems Division 10 Corporate Drive Orangeburg, New York 10962 USA Sensormatic Electronics Corporation American Dynamics Business Unit State Rd. 110 Km 5.8 Poblado San Antonio Aguadilla P. R.
Additional information: These products herein, comply with the requirements of the EMC Directive 89/336/EEC. The equipment was tested in a typical configuration. Orangeburg, NY, USA, 31 January 1996 Dennis Dodrill, Manager Quality Assurance and Technical Services This representative has the technical documentation and the declaration of conformity on file.
SPECIFICATIONS Supply Voltage: AD1650B: 120VAC, 50/60 Hz ADE1650B: 230V , 50 Hz ADK1650B: 230V , 50 Hz Power per Bay: 35 watts max. Mounting: Free standing or Rack mount Size per Bay: Desktop - 5.5" H x 14" D x 17" W (140 x 356 x 432 mm) Rack-mount - 5.
