Model 2083-06 Code Translator Installation and Operation Instructions This manual describes the installation and operating procedures for the model 2083-06 Code Translator. The 2083-06 Code Translator is an interface unit used with American Dynamics Switching Systems. This unit translates codes to enable the use of all American Dynamics equipment with that of Pelco Intercept Domes.
This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the purchaser under a license for use on a single system. NOTE: Information furnished by SENSORMATIC is believed to be accurate and reliable.
AMERICAN DYNAMICS The installation of this product should be made by qualified service personnel and should conform to all local codes. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Table of Contents Product Description ...............................................................1 Installation .............................................................................1 Setup ......................................................................................2 Camera Block Assignment...............................................2 Camera Mode ...................................................................2 Baud Rate Selection .................................................
DESCRIPTION S1 S2 DATA LINE GROUP IN 1 ABCD T + T R + R T + T R + R T T R R T T R R T T R R T T R R T T R R T T R R + + + BWS NO NC C 2 ABCD T T R R T T R R T T R R T T R R + POWER + + + + + + + OUT 3 ALARM ABCD + + + + CODE + + + + 4 ABCD T + S4 T R + R T + T R + R T + T R + R T + T R + R 120V 60Hz C O M INPUT OUTPUT S3 Figure 1 - 2083-06 Code Translator - Rear Panel PRODUCT DESCRIPTION Rack Mounting The 2083-06 Code Tr
SETUP SETUP - CAUTION The following internal adjustments expose hazardousvoltage components and allow access to dangerous electric shock potentials. These adjustments should be made only by qualified service personnel. Camera Block Assignments The 2083-06 Code Translator must be set to identify the range of camera numbers to be controlled by the unit.
SETUP Table 3 - CAMERA NUMBER RANGE The following table shows the DIP switch settings for the camera number range of each connector group. The active positions of switches S1 - S4 are labeled A, B, C, and D on the rear panel (Figure 1). The active positions of DIP switch S6 are labeled 1 through 8 on the internal DIP switch (Figure 3). The switch settings differ according to the Camera Mode set (Table 1, page 2). Switch S6 is used for Camera Modes 32 and 16 only.
SETUP Table 3 - CAMERA NUMBER RANGE (Continued) The following table shows the DIP switch settings for the camera number range of each connector group. The active positions of switches S1 - S4 are labeled A, B, C, and D on the rear panel (Figure 1). The active positions of DIP switch S6 are labeled 1 through 8 on the internal DIP switch (Figure 3).
CONNECTIONS CONNECTIONS Pelco Interface Connectors Data Line Connectors Eight 12-pin connectors on the rear panel of the 2083-06 are used for transmitting and receiving codes with Pelco Intercept Domes. Each connector provides two separate RS-422 connections, for cameras that are within the selected camera number range of that group. The transmit (T) and receive (R) signal pins are labeled on each connector. Each connector is supplied with a mating screw terminal connector (Figure 4).
OPERATION OPERATION Controlling Pelco Receiver Features Power Sources The 2083-06 supports the transmitted codes for Pelco Intercept Domes features. This includes the standard American Dynamics keyboard functions for camera Pan, Tilt, and Lens control. For those Pelco domes which implement preset capability, the 2083-06 supports AD keyboard commands for 32 presets per receiver. DO NOT CONNECT THE EQUIPMENT TO A POWER SOURCE UNTIL READY TO "POWER UP''.
OPERATION Table 4 - Pelco Intercept Dome Commands Pelco Function Dome Action AD Keyboard Command Pan, Tilt, Zoom, Focus, and Iris Functions Pan, Tilt, Zoom, Focus, and Iris Controls Presets (For those Pelco domes which implement preset capability): Set Preset 1 - 32 Saves camera position as preset 1 - 32 Goto Preset 1 - 32 Moves camera to preset position 1 - 32 1 - 32 Set Shot 1 - 32 Call Shot Auxiliaries: Set AUX 1 - 3 Set AUX 4 Set AUX 5 Set AUX 6 Set AUX 7 Set AUX 8 Clear AUX 1-3 Clear AUX 4 Clea
APPENDIX
TYPICAL SYSTEM CONNECTIONS 1995 TO 2083-06 DATA LINE GROUP IN 1 ABCD T + T R + R T + T R + R T T R R T T R R T + T R R T T R R T T R R T T R R + + + BWS NO NC C 2 ABCD POWER + T T R R T T R R T T R R T T R R + + + + + + OUT 3 ALARM ABCD + + + + + CODE + + + 120V 60Hz C O M 4 ABCD T + T R + R T + T R + R T + T R + R T + T R + R INPUT OUTPUT 2083-06 COAX CABLE RST PORT 10 LAN 1 PORT 9 IN OUT PORT 8 LAN 2 PORT 7 IN
TYPICAL SYSTEM CONNECTIONS 1650 TO 2083-06 DATA LINE GROUP IN 1 ABCD T + T R + R T + T R + R T T R R T T R R T T R R T T R R T T R R T T R R + + + BWS NO NC C 2 ABCD POWER T T R R T T R R T T R R T T R R + + + + + + + + OUT 3 ALARM ABCD + + + + CODE + + + + 120V 60Hz C O M 4 ABCD T + T R + R T + T R + R T + T R + R T + T R + R INPUT OUTPUT 2083-06 B W S W 18 AWG SHIELDED TWISTED PAIR BELDEN 8760 OR EQUIVALENT B S R
TYPICAL SYSTEM CONNECTIONS 1024 CPU TO 2083-06 DATA LINE GROUP IN 1 ABCD T + T R + R T + T R + R T T R R T T R R T + T R R T T R R T T R R T T R R + + + BWS NO NC C 2 ABCD POWER + T T R R T T R R T T R R T T R R + + + + + + OUT 3 ALARM ABCD + + + + + CODE + + + 120V 60Hz C O M 4 ABCD T + T R + R T + T R + R T + T R + R T + T R + R INPUT OUTPUT 2083-06 COAX CABLE DATA LINE PROG MON PORTS 120V 60Hz 1 2 1 2 3 4
TYPICAL SYSTEM CONNECTIONS 2150 TO 2083-06 DATA LINE GROUP IN 1 T ABCD + T R + R T + TR + R T TR R T T R R T TR R T T R R T TR R T T R R + + + BWS NO NC C 2 ABCD T T R R T TR R T T R R T TR R + POWER + + + + + + + OUT 3 ALARM ABCD + + + + + CODE + + + 120V 60Hz C O M 4 ABCD T + T R + R T + TR + T R + TR + R T + T R + R INPUT OUTPUT 2083-06 B W S 18 AWG SHIELDED TWISTED PAIR, BELDEN 8760 OR EQUIVALENT B 2 3 4 S A
TYPICAL SYSTEM CONNECTIONS 2083-06 to Pelco Interceptor Dome 25-pin CONNECTOR PLUG, P13 in Pelco Back Box 1 P13 Pins: 3 - R+ 5 - T+ 6 - R7 - T- 20 16 19 12 15 7 PELCO BACK BOX 11 6 PELCO INTERCEPTOR DOME 25 18 AWG, SHIELDED CABLE T T R + R T + T R + R + DATA LINE GROUP 1 ABCD T + T R + R T + T R + R IN T T R R T TR R T T R R T TR R T T R R T TR R + + + BWS NO NC C 2 ABCD POWER T T R R T T R R T T R R T T R R + + + + + + + + OUT 3 AL
Declaration of Conformity Manufacturer: Sensormatic Video Systems Division Manufacturer’s Address: Sensormatic Video Systems Division 1 Blue Hill Plaza Pearl River, New York, 10965 USA Sensormatic Electronics Corporation State Rd. 110 Km 5.8 Poblado San Antonio Aguadilla P.R. 00690 Declares, that the product(s) listed below: Name/Type: Code Translator Model Number: ADS2083-06X complies with the EMC Standards EN55022 (Class B), EN50082-1, and also complies with the following safety standard: EN60950.
SPECIFICATIONS Electrical Ratings: Mounting: Weight: Dimensions: AD2083-06: ADS2083-06X 120 VAC, 50/60 Hz, 8 W 230 VAC, 50/60 Hz, 100 mA Desktop or rack-mount 7 lbs. (3.2 Kg) 3.5" H x 17" W x 7.
