Installation and Operating Manual Advantage DK ADV-1000 ADV-1000i (intercom) Digital Access Control Station “Your Partner in Access Control” www.americanaccess.
Contents Two-Year Limited Warranty PARTS CHECKLIST INTRODUCTION INSTALLATION HARNESS COLOR CODES WIRING CONNECTIONS THE IDLE MODE ACCESS CODES AND FUNCTION CODES GOOD TONES and ERROR TONES PROGRAMMING THE DK UNIT Program Relay “A” Access Codes - Sub-Mode 1 Delete Individual Access Codes - Sub-Mode 2 Change the Master Code - Sub-Mode 3 Set Sleep Code -- Sub-Mode 4 Set Latch Code -- Sub-Mode 5 Set Relay Output Times -- Sub-Mode 6 Program Relay “B” Access Codes -- Sub-Mode 7 Enable or Disable the “Three Strike
Two-Year Limited Warranty This Warranty applies to: American Access Systems “Advantage DK” access controls What is Covered: Any defects in materials or workmanship Coverage Period: Two years from date of purchase What We Will Do: If your American Access System (AAS) product is defective and returned within two years of purchase, well will repair, or at our option, replace the unit at no charge to you. If we repair your AAS Product, we may use new or reconditioned parts.
Parts Checklist Parts that are included in the box include the following items.
Introduction The American Access Systems (AAS) Advantage DK unit is a high-quality, user-programmable, commercial-duty digital key control station designed to control access to a passageway using 4-digit access codes. The Advantage DK integrates state-of-the-art electronics resulting in a product which is highly sophisticated, yet inexpensive. The Advantage DK unit features: • 1 programmable 4-digit Master Code.
Standard Hook-up Diagram for Advantage ADV-1000 Page 6 American Access Systems / Security Brands, Inc.
BOARD LAYOUT _______________________________________________ _______________________________________________ _______________________________________________ Page 7 American Access Systems / Security Brands, Inc.
• Carefully study the diagram that best suits the installation conditions. The following is a key to the wire harness color codes. HARNESS COLOR CODES WHITE (AC Hot) (DC +) 11.5 - 29 volts AC or DC WHITE (AC Neutral)(DC -) 11.5 - 29 volts AC or DC GREEN EARTH GROUND ONLY RELAY A (PRIMARY) CONTROL COLOR CODES BROWN 11.
THE IDLE MODE When the desired connections are complete and power is supplied to the unit, the unit will be in the IDLE MODE. The IDLE MODE is the normal mode of operation, meaning the unit is ready to accept input from the keypad. When in the IDLE MODE, you have approximately 4 seconds between key presses. If this time is exceeded, you will receive an ERROR TONE. Any time you hear an ERROR TONE, simply begin whatever operation you were attempting over again.
GOOD TONES and ERROR TONES The DK unit sounds an audible tone each time a key is pressed. The star (ã) key serves as the clear key and a double tone is sounded when the star (ã) key is pressed. The pound (#) key is the exit key and exits the programming mode any time it is pressed. • A “GOOD TONE” is an oscillating high tone. It is very distinct. • An “ERROR TONE” is represented by a single low tone. It also is very distinct.
PROGRAMMING THE DK UNIT To access the program mode, enter the MASTER CODE. When the correct MASTER CODE is entered the yellow LED will light and a GOOD TONE will sound. You can now enter any of ten programming SUB MODES described below.
Change the Master Code -- Sub-Mode 3 To change the Master Code: • Enter the current Master Code • Unit will sound a GOOD TONE• Press the numeral 3 • Enter a new Master Code • Unit will sound a GOOD TONE • If you make an entry error, simply press the star (ã) key and enter the number you wish • Press the pound (#) key to exit the programming modeNOTES: • Be sure to make a note of the new Master Code. It is the password to system operation.
Enable or Disable the “Three Strikes … You’re Out” feature -- Sub-Mode 8 DETAILS: This “anti-tampering” feature is designed to help keep an unauthorized individual from continually entering codes until they “hit” a programmed Access Code. When the “Three Strikes …You’re Out” feature is enabled, if anyone enters 3 incorrect Access Codes within 90 seconds, the “Three Strikes …You’re Out” feature will literally shut down the unit for 90 seconds.
Erase All Codes -- Sub-Mode 0 Caution: This is a destructive Programming Mode. Completing the following steps will erase all Access Codes except for the factory default Master Code (1 2 5 1). Use with Caution. DETAILS: This Sub-Mode should rarely be used unless you want to completely erase all Access Codes entered. This action will not change the Master Code.
Troubleshooting Problem Solution When I enter 1 2 5 1 on the keypad the gate will not open. 1 2 5 1 is the Master Code or programming access code. It will not open the gate unless the unit is in sleep mode. Program a gate access code into the unit using Sub-Mode 1 (listed in the programming instructions). No response from keypad. Adjust the MIC and /or SPEAKER pots on circuit board to desired levels. A m Verify power input across the two white wires on the main harness.
Customer Service and Tech Support Customer Service: 303-799-9757 Customer service is available free of charge. Hours are 8:00 a.m. to 4:30 p.m. MST. If you call, please have your Model and Serial Number to help our Technicians assist you. E-Mail: customerservice@securitybrandsinc.com Technical Support: 303-799-9757 Technical support is available free of charge. Hours are 8:00 a.m. to 4:30 p.m. MST. If you call, please have your Model and Serial Number to help our Technicians assist you.
Notes Use this space to keep a record of Access Codes and the MASTER Code Page 17 American Access Systems / Security Brands, Inc.
Notes Use this space to keep a record of Access Codes and the MASTER Code Page 18 American Access Systems / Security Brands, Inc.
Notes Use this space to keep a record of Access Codes and the MASTER Code Page 19 American Access Systems / Security Brands, Inc.
“Your partner in access control” www.securitybrandsinc.
