User manual

ManualsBrandsAMD ManualsComputer equipmentPCM-5820

User Manual

3&0

6%&Z$0'/;9*$

/&'/$186%DQG66'

QG Ed - 6HSWHPEHU 20

Version: January 2013

Summary of content (111 pages)

PAGE 1
User Manual 3&0 6%& Z $0' /; 9*$ /&' /$1 86% DQG 66' QG Ed - 6HSWHPEHU 20 Version: January 2013
PAGE 2
Copyright This document is copyrighted, © 2006. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
PAGE 3
Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCM-9375 SBC • 1 Startup manual • 1 Utility CD • 1 mini jumper pack p/n: 9689000002 • 1 Audio cable p/n: 1700160160 • 1 IDE 44 pin cable p/n: 1701440351 • 1 USB 2 port Cable p/n: 1703100121 • 1 Parallel port cable p/n: 1700001977 • 1 Keyboard/Mouse cable p/n: 1700060202 • 1 x COM2/3/4 cable p/n: 1700001971 • 1 x LAN cable p/n: 1701100202 • Optional Accessories - 1700002150
PAGE 4
Additional Information and Assistance 1.Visit the Advantech web site at www.advantech.com where you can find the latest information about the product. 2.Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
PAGE 5
This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the following two conditions: 1.This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
PAGE 6
PCM-9375 User Manual vi Data Modul AG - www.data-modul.
PAGE 7
Contents Chapter 1 Introduction ......................................................2 1.1 1.2 1.3 Introduction ....................................................................... 2 Features ............................................................................. 2 Specifications .................................................................... 3 1.3.1 1.3.2 1.3.3 1.3.4 1.3.5 1.3.6 1.4 Standard 3.5" Biscuit SBC Functions............................. 3 VGA/LVDS Interface ....................
PAGE 8
2.8 2.9 2.10 Parallel port connector (CN17) ....................................... 14 Keyboard and PS/2 mouse connector (CN14) ................ 15 Power & HDD LED Connector (LED1, CN3) ............... 15 2.10.1 Power & HDD LED Connector(LED1)........................ 15 2.10.2 Power Reset button (CN3)............................................ 15 2.11 Power connectors (CN2) ................................................. 15 2.11.1 Main power connector, +5 V, +12 V (CN2)................. 15 2.11.
PAGE 9
4.1.3 4.2 4.2.1 4.3 Chapter AMD Geode LX ........................................................... 45 Table 4.1:Connections to Sharp LQ121S1DG31 / PCM937545 Installation of the VGA and AES Driver ........................ 47 4.3.1 4.3.2 4.3.3 4.4 CMOS setting for panel type ....................................... 44 Connections to Two Standard LCDs............................... 45 Installation chipset AES driver ..................................... 47 Installation of VGA driver.................
PAGE 10
A.13 Print Port (CN17) ...................................................... 81 A.14 RS-422/485 (CN18) .................................................. 83 A.15 COM1 (CN19).......................................................... 83 A.16 ISA -5 V & -12 V Input (CN21) ................................. 84 A.17 Audio (CN22)........................................................... 85 A.18 LAN1 (CN23)........................................................... 86 A.19 LAN2 (CN24)................
PAGE 11
CHAPTER 1 General Information This chapter gives background information on the PCM-9375. Sections include: • Introduction • Features • Specifications • Board layout and dimensions Data Modul AG - www.data-modul.
PAGE 12
Chapter 1 Introduction 1.1 Introduction The PCM-9375 is a fanless, best-cost, performance 3.5" SBC (Single Board Computer) geared to satisfy the needs for various industrial computing equipment. PCM-9375 is ideal for communication, gaming and medical applications that require flat panel support using digital displays with TTL or LVDS interfaces and two Ethernet ports.
PAGE 13
1.3 Specifications 1.3.1 Standard 3.5" Biscuit SBC Functions • CPU: AMD Geode® LX800 processor, up to 500 MHz • System Memory: 1 x SODIMM socket, support Double Data Rate (DDR) SDRAM, Max 512 MB, accept 128/256/512 MB, DDR333 SDRAM • 2nd Cache Memory: 128 KB on the processor • System Chipset: AMD Geode LX800 • BIOS: AWARD 4 Mbit Flash BIOS • Watchdog timer: 255 levels timer interval • Expansion Interface: PC/104 • Battery: Lithium 3V/196 mAH • Power management: APM 1.
PAGE 14
1.3.3 Ethernet Interface • Chipset supports: 2 x 10/100Mbps - Realtek RTL8100 • Interface: 1 x RJ-45 connector, and 1 x internal box header • Connector: One RJ-45 connector, and one internal box header • Standard IEEE 802.3u (100 BASE-T) protocol compatible • Built-in boot ROM (RTL8100) 1.3.4 Audio Function • Audio controller: Realtek ACL203 chipset, supports AC97 3D Audio stereo sound • Audio interface: Microphone in, Line in, Line out, Speak out 1.3.
PAGE 15
98.57 101.60 99.38 98.79 98.37 95.25 87.63 86.36 83.82 143.33 146.05 133.99 134.30 135.70 142.82 105.09 110.49 111.54 77.98 86.74 87.63 2.22 4.45 6.99 8.89 16.70 1.90 1.4 Board layout: dimensions 101.60 L2 98.37 95.25 94.30 89.99 88.58 74.92 73.66 70.49 65.76 19.60 17.10 15.60 10.16 9.84 6.95 5.77 3.18 18.14 137.62 140.97 142.82 146.05 125.37 111.45 112.21 84.58 87.63 78.03 55.37 54.64 49.73 22.12 8.89 0.00 1.90 12.40 8.61 7.77 7.62 5.84 5.77 0.00 143.33 146.05 133.99 134.30 135.
PAGE 16
26.30 7.70 11.60 8.60 14.15 18.40 14.60 13.85 11.60 13.80 14.15 12.65 9.50 7.00 21.56 97.47 Figure 1.3: Dimension of PCM-9375 for H 92.93 1 3 7NC 2 1 2 3 01NC 0.00 0.00 Figure 1.4: PCM-9375 Mechanical Drawing(Solder side) PCM-9375 User Manual 6 Data Modul AG - www.data-modul.com 53.
PAGE 17
CHAPTER 2 Installation This chapter explains the setup procedures of the PCM-9375 hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all safety precautions before you begin the installation procedure. Data Modul AG - www.data-modul.
PAGE 18
Chapter 2 Installation 2.1 Jumpers The PCM-9375 has a number of jumpers that allow you to configure your system to suit your application. The table below lists the functions of the various jumpers. Table 2.1: Jumpers Label Function J1 AT/ATX Selector J2 Clear CMOS J3 COM2 Setting J4 Audio Power J5 TV Enable 2.1.1 AT/ATX Selector(J1) Table 2.2: AT/ATX Selector(J1) Setting 1-2* None *: default Function AT ATX 2.1.2 Clear CMOS(J2) Table 2.
PAGE 19
2.1.4 Audio Power (J4) Table 2.5: Audio Power (J4) Setting 1-2* 2-3 *: default Function With + 12 v Without + 12 V 2.1.5 TV enable (J5) Table 2.6: TV enable Setting Function 1-2* TV Enable NONE TV Disable *: default 9 Data Modul AG - www.data-modul.
PAGE 20
2.2 Connectors Onboard connectors link the PCM-9375 to external devices such as hard disk drives, a keyboard, or floppy drives. The table below lists the function of each of the board’s connectors. Table 2.
PAGE 21
2.3 Locating Connectors Figure 2.1: Connectors (component side) Figure 2.2: Connectors (solder side) 11 Data Modul AG - www.data-modul.
PAGE 22
2.4 Setting Jumpers You may configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, you connect the pins with the clip. To “open” a jumper, you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
PAGE 23
2.5 Installing SO-DIMM Module Key Aligned With housing Key 2 Housing Card Slot PC Board 1 Module Tilted Approximately 25 3 Module Latching Ledge(TO Engage Edge of Module) The procedures for installing SODIMMs are described below. Please follow these steps carefully. You can install SDRAM memory modules using 200-pin SODIMMs (Small Outline Dual In-line Memory Modules). 1. Ensure that all power supplies to the system are switched off. 2.
PAGE 24
2.6 IDE, CDROM hard drive connector (CN11) The board provides 1 IDE channels which you can attach up to two Enhanced Integrated Device Electronics hard disk drives or CDROM to the board’s internal controller. Its IDE controller uses a PCI interface. This advanced IDE controller supports faster data transfer, PIO mode 3, mode 4 and up to UDMA33. 2.6.1 Connecting the hard drive Connecting drives is done in a daisy-chain fashion. This package includes One 44PIN IDE cable that can connect to 1.8" and 2.
PAGE 25
2.9 Keyboard and PS/2 mouse connector (CN14) The board provides a keyboard connector that supports both a keyboard and a PS/2 style mouse. In most cases, especially in embedded applications, a keyboard is not used. If the keyboard is not present, the standard PC/AT BIOS will report an error or fail during power-on self-test (POST) after a reset. The PCM board’s BIOS standard setup menu allows you to select “All, But Keyboard” under the “Halt On” selection.
PAGE 26
2.12 Audio interfaces (CN22) 2.12.1 Audio connector (CN22) The board provides all major audio signals on a 10-pin cable connector, These audio signals include Microphone in (mono), Line in (stereo) and Line out (stereo). 2.13 COM port connector (CN16,CN19) The board provides four serial RS-232 ports (CN19: COM1) in one DB-9 connector and one Hirose 40 pin connector (CN16: COM2/3/4) with auto-flow control. It provides connections for serial devices (a mouse, etc.) or a communication network.
PAGE 27
2.14 VGA/LCD/LVDS interface connections The board’s PCI SVGA interface can drive conventional CRT displays and is capable of driving a wide range of flat panel displays. 2.14.1 CRT display connector (CN12) The CRT display connector is a 15-pin D-SUB connector used for conventional CRT displays. 2.14.2 TTL TFT LCD connector (CN4) For PCM-9375F series, CN4 consists of a 40-pin connector which can support up to 24-bit LCD panel. It is Hirose’s product no. DF13A-40DP1.25 V 2.14.
PAGE 28
2.17 USB connectors (CN13,CN15) The board provides up to four USB (Universal Serial Bus) ports using Plug and Play. The USB interfaces comply with High Speed USB specification Rev. 2.0 which supports 480Mbps transfer rate, and are fuse protected. The USB interface is accessed through two 5 x 2-pin flat-cable connectors. You will need an adapter cable if you use a standard USB connector. The adapter cable has a 5 x 2-pin connector on one end and a USB connector on the other.
PAGE 29
CHAPTER 3 BIOS Operation 7 Chapter 3 Data Modul AG - www.data-modul.
PAGE 30
Chapter 3 BIOS Operation 3.1 BIOS Introduction PCM-9375 comes with Award’s BIOS 6.0 that delivers superior performance, compatibility and functionality, it’s many options and extensions let you customize your products to a wide range of designs and target markets. The modular, adaptable Award BIOS 6.
PAGE 31
Table 3.1: Controll Keys Item Help Load Previous Values Load Optimized Default Save all CMOS changes 3.2.1 Main Menu Press to enter Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. Use arrow keys to select among the items and press to accept or enter the sub-menu. • Standard CMOS Features This setup page includes all the items in standard compatible BIOS.
PAGE 32
This setup page includes all the items of Power Management features. • PnP/PCI Configurations This setup page includes PnP OS and PCI device configuration. • PC Health Status This setup page includes the system auto detect CPU and system temperature, voltage, fan speed. • Load Optimized Defaults This setup page includes Load system optimized value, and the system would be in best performance configuration. • Set Password Establish, change or disable password.
PAGE 33
3.2.2 Standard CMOS Features • Date The date format is , , , . Week From Sun to Sat, determined and display by BIOS only Month From Jan to Dec. Day From 1 to 31 Year From 1999 through 2098 • Time The times format in , base on the 24-hour time. • IDE Channel 0 Master/Slave IDE HDD Auto-Detection Press "Enter" for automatic device detection. • IDE Channel 1 Master/Slave IDE HDD Auto-Detection Press "Enter" for automatic device detection.
PAGE 34
720K, 3.5" 3.5 inch double-sided drive; 720K byte capacity 1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity 2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity • Halt on The item determines whether the computer will stop if an error is detected during power up. No Errors The system boot will not stop for any error. All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.
PAGE 35
3.2.3 Advanced BIOS Features • Virus Warning [Disabled] This item allows user to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. • CPU Internal Cache [Enabled] This item allows user to enable CPU internal cache. • Quick Power On Self Test [Enabled] This field speeds up the Power-On Self Test (POST) routine by skipping retesting a second, third and forth time. Setup setting default is enabled.
PAGE 36
• Boot Up Floppy Seek [Enabled] When enabled, the BIOS will seek the floppy “A” drive one time • Boot Up NumLock Status [On] This item enables users to activate the Number Lock function upon system boot • Gate A20 Option [Fast] This item enables users to switch A20 control by port 92 or not. • Typematic Rate Setting [Disabled] This item enables users to set the two typematic controls items.
PAGE 37
It’s for shadow control of item. D4000-D7FFF Shadow [Disabled] It’s for shadow control of item. D8000-DBFFF Shadow [Disabled] It’s for shadow control of item. DC000-DFFFF Shadow • Small Logo (EPA) Show [Disabled] [Enabled] Show EPA logo during system post stage • Cyrix 6X86/MII CPUID [Enabled] This item allows user to control bios enabled or disabled CPUID for CPU Cyrix/MII. 15 Data Modul AG - www.data-modul.
PAGE 38
3.2.4 Advanced Chipset Features NOTE: This “Advanced Chipset Features” option controls the configuration of the board’s chipset, this page is developed by Chipset independent, for control chipset register setting and fine tune system performance. It is strongly recommended only technical users make changes to the default settings. • CPU Frequency [Enabled] This item enables users to set the CPU Host clock by system automatic detection or by manual.
PAGE 39
• Onboard USB1.1 [Enabled] This item is controller to enabled or disabled motherboard of USB1.1 device. • Onboard USB2.0 [Enabled] This item is controller to enabled or disabled motherboard of USB2.0 device. • Onboard IDE [Enabled] This item is controller to enabled or disabled motherboard of IDE device. • Memory Hole At 15M-16M[Disabled] This item reserves 15MB-16MB memory address space to ISA expansion cards that specifically require the setting.
PAGE 40
3.2.5 Integrated Peripherals NOTE: This “Integrated Peripherals” option controls the configuration of the board’s chipset, includes IDE, ATA, SATA, USB, AC97, MC97 and Super IO and Sensor devices, this page is developed by Chipset independent. • On-Chip IDE Channel 1 This item enables chipset IDE device 1 of controller. • Master Drive PIO Mode [Auto] This item allows user to adjust master IDE mode of type for modification purpose. Bios default value suggest to “Auto”.
PAGE 41
• LAN1 Controller [Enabled] This item is enabled or disabled that onboard of LAN1 controller. Bios default value suggest to “Enabled”. • LAN2 Controller [Enabled] This item is enabled or disabled that onboard of LAN2 controller. Bios default value suggest to “Enabled”. • ITE8888 Configure [Press Enter] This item allows user to changed ITE8888 of detail adjust. • IDE HDD Block Mode [Enabled] This item allows enabled or disabled that IDE block data transfer mode.
PAGE 42
• Onboard Serial Port 4 [2E8] This item allows user to change com 4 of address. Bios default value suggest to “2E8”. • Onboard Serial Port 4 use [IRQ5] This item allows user to change com 4 of IRQ. Bios default value suggest to “IRQ5”. • Auto Flow Control [Disabled] This item allows user to control com port of auto flow transfer. Bios default value suggest to “Disabled”. • Onboard Parallel Port [378/IRQ7] This item allows user to change parallel port of address.
PAGE 43
3.2.6 Power Management Setup NOTE: This “Power management Setup” option configure system to most effectively saving energy while operating in a manner consistent with your computer use style. • ACPI Function [Enabled] (Show Only) This item defines the ACPI (Advanced Configuration and Power Management) feature that makes hardware status information available to the operating system, and communicate PC and system devices for improving the power management.
PAGE 44
• Modem use IRQ [N/A] This item allows user to determine the IRQ which the MODEM can use. • Soft-Off by PWR-BTTN [Instant-Off] This item allows user to define function of power button. Instant-Off Press power button then Power off instantly. Delay 4 Sec Press power button 4 sec. to Power off. • Power-On by Alarm [Disabled] This item allows user to enable and key in Date/time to power on system. Disabled Disable this function. Enabled Enable alarm function to power on system.
PAGE 45
3.2.7 PnP/PCI Configurations NOTE: This “PnP/PCI Configurations” option is setting up the IRQ and DMA (both PnP and PCI bus assignments. • PNP OS Installed [No] This item allows user to determine PNP function install or not. • Init Display First [Onboard] This item is setting for start up Video output from Onboard or PCI device. • Reset Configuration Data [Disabled] This item allow user to clear any PnP configuration data stored in the BIOS.
PAGE 46
3.2.8 PC Health Status NOTE: This “PC Health Status” option controls the Thermal, FAN and Voltage status of the board. this page is developed by Chipset independent. • Shutdown Temperature [60°C/70°C] This item enables users to set the limitation of CPU temperature, the range is from 60°C through 70°C. • Current System/CPU Temp [Show Only] This item displays current system and CPU temperature. • 3.3V / 5V / 12V [Show Only] This item displays current CPU and system Voltage.
PAGE 47
3.2.9 Load Optimized Defaults NOTE: Load Optimized Defaults loads the default system values directly from ROM. If the stored record created by the Setup program should ever become corrupted (and therefore unusable). These defaults will load automatically when you turn the PCM-9375 Series system on. 25 Data Modul AG - www.data-modul.
PAGE 48
3.2.10 Set Password NOTE: To enable this feature, you should first go to the Advanced BIOS Features menu, choose the Security Option, and select either Setup or System, depending on which aspect you want password protected. Setup requires a password only to enter Setup. System requires the password either to enter Setup or to boot the system. A password may be at most 8 characters long. To Establish Password 1. Choose the Set Password option from the CMOS Setup Utility main menu and press . 2.
PAGE 49
4. Select Set Password again, and at the “Enter Password” prompt, enter the new password and press . 5. At the “Confirm Password” prompt, retype the new password, and press . 6. Select Save to CMOS and EXIT, type , then . To Disable Password 1. Choose the Set Password option from the CMOS Setup Utility main menu and press . 2. When you see “Enter Password”, enter the existing password and press . 3. You will see “Confirm Password”. Type it again, and press . 4.
PAGE 50
3.2.11 Save & Exit Setup NOTE: Type “Y” will quit the BIOS Setup Utility and save user setup value to CMOS. Type “N” will return to BIOS Setup Utility. PCM-9375 User Manual 28 Data Modul AG - www.data-modul.
PAGE 51
3.2.12 Quit Without Saving NOTE: Type “Y”will quit the BIOS Setup Utility without saving to CMOS. Type “N” will return to BIOS Setup Utility. 29 Data Modul AG - www.data-modul.
PAGE 52
PCM-9375 User Manual 30 Data Modul AG - www.data-modul.
PAGE 53
CHAPTER 4 PCI SVGA/LCD Setup This chapter details the software configuration information. It shows you how to configure the card to match your application requirements. The AWARD System BIOS is covered in Chapter 4. Sections include: • Installation of SVGA drivers - for Window XP • Connections for standard LCDs • Further information Data Modul AG - www.data-modul.
PAGE 54
Chapter 4 PCI SVGA/LCD Setup 4.1 Introduction PCM-9375 has an onboard AMD Geode LX800 chipset for its AGP/ SVGA controller. It supports TFT LCD displays and conventional analog CRT monitors with 64 MB frame buffer shared with system memory. The VGA controller can drive CRT displays with resolutions up to 1600 x 1200 x 16 bpp at 100 Hz and up to 1024 x 768 x 32 bpp at 60 Hz for TFT LCD. 4.1.
PAGE 55
4.2 Connections to Two Standard LCDs Connector Table of 12.1" TTL Sharp LQ121S1DG31 800 x 600 5/3.3 V (18 Bit) for PCM-9375 AMD Geode LX. 4.2.1 AMD Geode LX Table 4.1: Connections to Sharp LQ121S1DG31 / PCM-9375 Sharp LQ121S1DG31 PCM-9375 DF9MA-41P-1V DF-13 4OP-1.
PAGE 56
Table 4.1: Connections to Sharp LQ121S1DG31 / PCM-9375 25 G5 24 D15 26 GND 33 GND 27 GND 28 GND 33 GND 29 B0 11 D2 30 B1 12 D3 31 B2 13 D4 32 GND 34 GND 33 B3 14 D5 34 B4 15 D6 35 B5 16 D7 36 GND 34 GND 37 ENAB 37 DE 38 NC 39 VCC 5 +3.3 V 40 VCC 6 +3.3 V 41 NC * The polarity of both synchronous signals are negative. PCM-9375 User Manual 34 Data Modul AG - www.data-modul.
PAGE 57
4.3 Installation of the VGA and AES Driver Complete the following steps to install the VGA and AES driver. Follow the procedures in the flow chart that apply to the operating system that you are using within your board. Notes: 1. The windows illustrations in this chapter are intended as examples only. Please follow the listed steps, and pay attention to the instructions which appear on your screen. 2. For convenience, the CD-ROM drive is designated as "D" throughout this chapter. 4.3.
PAGE 58
2. Go to driver page and click on update driver. 3. Click on install from specific folder and click on next. PCM-9375 User Manual 36 Data Modul AG - www.data-modul.
PAGE 59
4.Click on browse and select target folder, then, click OK. 5.Click on next. 37 Data Modul AG - www.data-modul.
PAGE 60
6. Click on finish. PCM-9375 User Manual 38 Data Modul AG - www.data-modul.
PAGE 61
4.3.2 Installation of VGA driver 1. Right click on video, and click “ Properties”. 2. Go to driver page and click on update driver. 39 Data Modul AG - www.data-modul.
PAGE 62
3. Click on install from specific folder and click on next. 4. Click on browse and select target folder, then click OK. PCM-9375 User Manual 40 Data Modul AG - www.data-modul.
PAGE 63
5. Click on next, then click on finish. 6. Then click on continue anyway. 41 Data Modul AG - www.data-modul.
PAGE 64
7. Click on finish. PCM-9375 User Manual 42 Data Modul AG - www.data-modul.
PAGE 65
4.3.3 PCI Bridge The system may detect the PCI bridge automatically. If the question mark is shown on device manager, please install the driver as below: 1. Click “Add Hardware Wizard” and add new hardware wizard 43 Data Modul AG - www.data-modul.
PAGE 66
2. Search the right directory of PCI bridge for IT8888G driver. PCM-9375 User Manual 44 Data Modul AG - www.data-modul.
PAGE 67
3. Installation finished. 4.4 Further Information For further information about the AGP/VGA installation of your PCM9375, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: AMD website: www.AMD.com Advantech websites: www.advantech.com www.advantech.com.tw 45 Data Modul AG - www.data-modul.
PAGE 68
PCM-9375 User Manual 46 Data Modul AG - www.data-modul.
PAGE 69
CHAPTER 5 Audio Setup The board is equipped with an audio interface that records and plays back CD-quality audio. This chapter provides instructions for installing the software drivers included on the audio driver diskettes. Data Modul AG - www.data-modul.
PAGE 70
Chapter 5 Audio Setup 5.1 Introduction The onboard audio interface provides high-quality stereo sound by using the Realtek ALC203 audio controller. The audio interface can record, compress, and play back voice, sound and music with built-in mixer control. 5.2 Driver installation 5.2.1 Before you begin Please read the instructions in this chapter carefully before you attempt installation. The audio drivers for the board are located on the audio driver CD.
PAGE 71
5.2.2 Windows XP drivers 1. Open device manager, right click on audio and click on “properties”. 2. Go to driver page and click on update driver. 49 Data Modul AG - www.data-modul.
PAGE 72
3. Click on install from specific folder and click on next. 4. Click on browse and select target folder, then click OK. PCM-9375 User Manual 50 Data Modul AG - www.data-modul.
PAGE 73
5. Click on next. 6. Click on continue anyway. 51 Data Modul AG - www.data-modul.
PAGE 74
7. Click on finish. Notes: The Audio driver is provided by AMD, do not download other audio drivers from Realtek website. PCM-9375 User Manual 52 Data Modul AG - www.data-modul.
PAGE 75
Appendix A Pin Assignments This appendix contains information of a detailed or specialized nature. It includes: • Stand-by Power Input • Power Input • Reset Button • TFT LCD/LVDS • Inverter Power • ATX Power Button • GPIO • CF • IDE • CRT • USB1/2, USB3/4 • COM2/3/4 • Print Port • RS-422/485 • COM1 • ISA - 5 V & - 12 V • Audio • LAN1/LAN2 Data Modul AG - www.data-modul.
PAGE 76
Appendix A Pin Assignments A.1 Stand-by Power Input (CN1) Table A.1: Stand-by Power Input (CN1) Part Number: 1655303020 Description: Wafer Box 2.0mm 3P180D w/Lock Pin Pin Name Signal Type 1 +5 VSB PWR 2 GND GND 3 PS OUT A.2 Power Input (CN2) 1 2 3 4 Table A.2: Power Input (CN2) Part Number: 1655204030 Description: Housing 5.08mm 4P 180D Male w/o Lock Pin Pin Name Signal Type 1 +12 V PWR 2 GND GND 3 GND GND 4 +5 V PWR PCM-9375 User Manual 54 Data Modul AG - www.data-modul.
PAGE 77
A.3 Reset Button (CN3) Table A.3: Reset Button (CN3) Part Number: 1601064400 Description: Push sw L=8.35mm Reset Button for MIC-2340 Pin Pin Name Signal Type 1 RST IN 2 GND GND 3 GND GND 4 GND GND A.4 TFT LCD (CN4) Table A.4: TFT LCD (CN4) (PCM-9375F) Part Number: 1653920200 Description: *CONN. DF13-40DP-1.25 V Pin Pin Name Signal Type 1 +5 V PWR 2 +5 V PWR 3 GND GND 4 GND GND 5 +3.3 V PWR 6 +3.
PAGE 78
Table A.4: TFT LCD (CN4) (PCM-9375F) Part Number: 1653920200 Description: *CONN. DF13-40DP-1.
PAGE 79
Table A.
PAGE 80
Table A.6: PCM-9375E-J0A1E pin assignment CN4 LVDS (PCM-9375E-J0A1E) Part Number: 1653910261 Footprint: SPH10X2 Description: CONN, SMD 10*2P 180D(M)DF13-20DP-1.
PAGE 81
A.5 Inverter Power (CN5) Table A.7: Inverter Power (CN5) Part Number: 1655305020 Description: Wafer box 2.0mm 5P 180D Male w/Lock Pin Pin Name Signal Type Signal Level 1 +12 V PWR +12 V 2 GND GND 3 ENABKL OUT 4 VBR OD +3.3 V 5 +5 V PWR +5 V +3.3 V 59 Data Modul AG - www.data-modul.
PAGE 82
A.6 ATX Power Button (CN8) 1 2 Table A.8: ATX Power Button (CN8) Part Number: 1655302020 Description: Wafer Box 2P 180D 2.0mmm Male w/Lock Pin Pin Name Signal Type 1 PWRBTN# IN 2 GND GND A.7 GPIO (CN9) Table A.9: GPIO (CN9) Part Number: 1653005261 Description: Pin Header SMD 5*2P 180D(M) 2.
PAGE 83
A.8 CF (CN10) 2 50 1 49 Table A.10: CF (CN10) Part Number: 1653025211 Description: Header for CF Type I 50P 90D(M) Standoff 2.0mm Pin Pin Name Signal Type 1 GND GND 2 D3 I/O 3 D4 I/O 4 D5 I/O 5 D6 I/O 6 D7 I/O 7 CS#1 OUT 8 A10 OUT 9 OE# OUT 10 A9 OUT 11 A8 OUT 12 A7 OUT 13 +5 V PWR 14 A6 IN 15 A5 IN 16 A4 IN 17 A3 IN 18 A2 IN 19 A1 IN 20 A0 IN 21 D0 I/O 22 D1 I/O 61 Data Modul AG - www.data-modul.
PAGE 84
Table A.10: CF (CN10) Part Number: 1653025211 Description: Header for CF Type I 50P 90D(M) Standoff 2.
PAGE 85
A.9 IDE (CN11) Table A.11: IDE (CN11) Part Number: 1653222262 Description: Box Header SMD 22*2P 180D(M) 2.0mm Pin Pin Name Signal Type 1 RST# OUT 2 GND GND 3 D7 I/O 4 D8 I/O 5 D6 I/O 6 D9 I/O 7 D5 I/O 8 D10 I/O 9 D4 I/O 10 D11 I/O 11 D3 I/O 12 D12 I/O 13 D2 I/O 14 D13 I/O 15 D1 I/O 16 D14 I/O 17 D0 I/O 18 D15 I/O 19 GND GND 21 DREQ OUT 22 GND GND 23 IOW# OUT 24 GND GND 63 Data Modul AG - www.data-modul.
PAGE 86
Table A.11: IDE (CN11) Part Number: 1653222262 Description: Box Header SMD 22*2P 180D(M) 2.0mm Pin Pin Name Signal Type 25 IOR# OUT 26 GND GND 27 IORDY OUT 28 CSEL# OUT 29 DACK# OUT 30 GND GND 31 IRO14 IN 32 NC 33 A1 IN 34 D66DET# IN 35 A0 IN 36 A2 IN 37 CS#1 OUT 38 CS#3 OUT 39 ASP# OUT 40 GND GND 41 +5 V PWR 42 +5 V PWR 43 GND GND 44 NC PCM-9375 User Manual 64 Data Modul AG - www.data-modul.
PAGE 87
A.10 CRT (CN12) Table A.12: CRT (CN12) Part Number: 1654515304 Description: D-SUB CONN. 15P 90D(F) DIP 5mm Blue Pin Pin Name Signal Type 1 R OUT 2 G OUT 3 B OUT 4 NC 5 GND GND 6 GND GND 7 GND GND 8 GND GND 9 +5 V PWR 10 GND GND 11 NC 12 DDAT OD I/O 13 HSYNC OUT 14 VSYNC OUT 15 DCLK OD I/O 65 Data Modul AG - www.data-modul.
PAGE 88
A.11 USB1/2 (CN13), USB3/4 (CN15) Table A.13: USB1/2 (CN13), USB3/4 (CN15) Part Number: 1653005260 Description: Pin Header 5*2P 180D(M) 2.0mm SMD Pin Pin Name Signal Type 1 +5 V PWR 2 +5 V PWR 3 P0- I/O 4 P1- I/O 5 P0+ I/O 6 P1+ I/O 7 GND GND 8 GND GND 9 GND GND 10 NC PCM-9375 User Manual 66 Data Modul AG - www.data-modul.
PAGE 89
A.12 COM2/3/4 (CN16) 29 1 30 2 Table A.14: COM2/3/4 (CN16) Part Number: 1653000221 Pin Pin Name Signal Type 1 DCD#2 IN 2 DSR#2 IN 3 RXD#2 IN 4 RTS2 IN 5 TXD2 OUT 6 CTS#2 IN 7 DTR#2 I/O 8 RI#2 IN 9 GND GND 10 GND GND 11 DCD#3 IN 12 DSR#3 IN 13 RXD3 IN 14 RTS#3 I/O 15 TXD3 OUT 16 CTS#3 IN 17 DTR#3 I/O 18 RI#3 IN 19 GND GND 20 GND GND 21 DCD#4 IN 22 DSR#4 IN 23 RXD4 IN 24 RTS#4 I/O 25 TXD4 OUT 67 Data Modul AG - www.data-modul.
PAGE 90
Table A.14: COM2/3/4 (CN16) Part Number: 1653000221 Pin Pin Name Signal Type 26 CTS#4 IN 27 DTR#4 I/O 28 RI#4 IN 29 GND GND 30 GND GND PCM-9375 User Manual 68 Data Modul AG - www.data-modul.
PAGE 91
A.13 Print Port (CN17) Table A.15: Print Port (CN17) Part Number: 1653000272 Description: Box Header SMD 13*2P 180D(M) 2.0mm Pin Pin Name Signal Type 1 STB# OUT 2 AFD# OUT 3 PD0 I/O 4 ERR# IN 5 PD1 I/O 6 INIT# OUT 7 PD2 I/O 8 SLIN# OUT 9 PD3 I/O 10 GND GND 11 PD4 I/O 12 GND GND 13 PD5 I/O 14 GND GND 15 PD6 I/O 16 GND GND 17 PD7 I/O 18 GND GND 19 ACK# IN 20 GND GND 21 BUSY IN 22 GND GND 23 PE IN 24 GND GND 69 Data Modul AG - www.
PAGE 92
Table A.15: Print Port (CN17) Part Number: 1653000272 Description: Box Header SMD 13*2P 180D(M) 2.0mm Pin Pin Name Signal Type 25 SLCT IN 26 NC PCM-9375 User Manual 70 Data Modul AG - www.data-modul.
PAGE 93
A.14 RS-422/485 (CN18) 1 2 3 4 Table A.16: RS-422/485 (CN18) Part Number: 1653004101 Description: Pin Header 4*1P 180D(M) SQUARE 2.0mm Pin Pin Name Signal Type 1 422-RXD- IN 2 422-RXD+ IN 3 485-422-TXD+ OUT 4 485-422-TXD- OUT A.15 COM1 (CN19) Table A.
PAGE 94
A.16 ISA -5 V & -12 V Input (CN21) 1 2 3 Table A.18: ISA -5 V & -12 V Input (CN21) Part Number: 1653003101 Description: Pin Header 3*1P 180D(M) SQUARE 2.0mm Pin Pin Name Signal Type 1 -12 V PWR 2 -5 V PWR 3 GND GND PCM-9375 User Manual 72 Data Modul AG - www.data-modul.
PAGE 95
A.17 Audio (CN22) 2 4 14 16 1 3 13 15 Table A.19: Audio (CN22) Part Number: 1653008260 Description: Pin Header 8*2P 180D SMD Male SQUARE PIN 2.0mm Pin Pin Name Signal Type 1 SPK OUT 2 SPK OUT 3 SPK OUT 4 SPK OUT 5 LOUT OUT 6 LOUT OUT 7 GND GND 8 GND GND 9 LIN IN 10 LIN IN 11 GND GND 12 GND GND 13 NC 14 MIC2 IN 15 MIC1 IN 16 GND GND 73 Data Modul AG - www.data-modul.
PAGE 96
A.18 LAN1 (CN23) 11 3 1 12 4 2 Table A.20: LAN1 (CN23) Part Number: 1652508200 Description: Phone Jack RJ-45 8P 90D(F) DIP 677-088-D06 Pin Pin Name Signal Type 1 LAN1-TX+ OUT 2 LAN1-TX- OUT 3 LAN1-RX+ IN 4 LAN1-LCT I/O 5 LAN1-LCT I/O 6 LAN1-RX- IN 7 LAN1-LCT I/O 8 LAN1-LCT I/O 11 GND GND 12 GND GND PCM-9375 User Manual 74 Data Modul AG - www.data-modul.
PAGE 97
A.19 LAN2 (CN24) Table A.21: LAN2 (CN24) Part Number: 1653205260 Description: Box Header SMD 5*2 180D (M) 2.0mm Pin Pin Name Signal Type 1 +3.3 V PWR 2 LAN2-ACTLED IN 3 LAN2-RX+ IN 4 LAN2-RX- IN 5 LAN2-LILED IN 6 LAN2-LCT I/O 7 NC 8 LAN2-LCT I/O 9 LAN2-TX+ OUT 10 LAN2-TX- OUT 75 Data Modul AG - www.data-modul.
PAGE 98
PCM-9375 User Manual 76 Data Modul AG - www.data-modul.
PAGE 99
Appendix B System Assignments This appendix contains information of a detailed nature. It includes: • System I/O ports • 1st MB memory map • DMA channel assignments • Interrupt assignments Data Modul AG - www.data-modul.
PAGE 100
Appendix B System Assignments B.1 System I/O Ports Table B.1: System I/O ports Addr.
PAGE 101
B.2 1st MB memory map Table B.2: 1st MB memory map Addr. range (Hex) F0000h - FFFFFh *CC000h - EFFFFh C0000h - CBFFFh B8000h - BFFFFh B0000h - B7FFFh A0000h - AFFFFh 00000h - 9FFFFh Device System ROM Unused (reserved for Ethernet ROM) Expansion ROM (for VGA BIOS) CGA/EGA/VGA text Unused EGA/VGA graphics Base memory * If Ethernet boot ROM is disabled (Ethernet ROM occupies about 16 KB) * E0000 - EFFFF is reserved for BIOS POST B.3 DMA channel assignments Table B.
PAGE 102
B.4 Interrupt assignments Table B.4: Interrupt assignments Interrupt# IRQ 0 IRQ 1 IRQ 2 IRQ 3 IRQ 4 IRQ 5 IRQ 6 IRQ 7 IRQ 8 IRQ 9 IRQ 10 IRQ 11 IRQ 12 IRQ 13 IRQ 14 Interrupt source Interval timer Keyboard Interrupt from controller 2 (cascade) COM2 COM1 Reserved (COM4) FDD LPT1 RTC Reserved (audio) Reserved (COM3) Reserved PS/2 mouse INT from co-processor Primary IDE PCM-9375 User Manual 80 Data Modul AG - www.data-modul.
PAGE 103
Appendix C Mechanical Drawings Data Modul AG - www.data-modul.
PAGE 104
Appendix C Mechanical Drawings 98.57 101.60 99.38 98.79 98.37 95.25 87.63 86.36 83.82 143.33 146.05 133.99 134.30 135.70 142.82 105.09 110.49 111.54 77.98 86.74 87.63 2.22 4.45 6.99 8.89 16.70 1.90 C.1 Mechanical Drawings 101.60 L2 98.37 95.25 94.30 89.99 88.58 74.92 73.66 70.49 65.76 19.60 17.10 15.60 10.16 9.84 6.95 5.77 3.18 18.14 137.62 140.97 142.82 146.05 125.37 111.45 112.21 84.58 87.63 78.03 55.37 54.64 49.73 22.12 0.00 1.90 8.89 12.40 8.61 7.77 7.62 5.84 5.77 0.
PAGE 105
143.33 146.05 133.99 134.30 135.70 142.82 105.09 110.49 111.54 77.98 86.74 87.63 1.90 2.22 4.44 6.98 8.89 16.60 101.60 99.38 98.79 98.37 95.25 87.63 86.36 83.82 101.60 98.37 95.25 94.30 89.99 88.58 74.92 73.66 70.49 65.76 19.60 17.10 15.60 10.16 9.84 6.95 5.77 3.18 18.14 137.62 140.97 142.82 146.05 125.37 111.45 112.21 84.58 87.63 78.03 49.73 55.37 54.64 22.12 8.89 0.00 1.90 12.40 8.61 7.77 7.62 5.84 5.77 0.00 9.50 7.00 26.30 7.70 11.60 8.60 18.40 14.15 14.60 13.85 13.
PAGE 106
97.47 21.56 92.93 1 3 7NC 2 1 2 3 01NC 0.00 0.00 Figure C.4: PCM-9375 Mechanical Drawing(Solder side) PCM-9375 User Manual 84 Data Modul AG - www.data-modul.com 53.
PAGE 107
Appendix D Watchdog Timer Data Modul AG - www.data-modul.
PAGE 108
Appendix D Watchdog Timer ;The SCH3114 Runtime base I/O address is 800h ;Setting WatchDog time value location at offset 66h ;If set value "0", it is mean disable WatchDog function. Superio_GPIO_Port = 800h mov dx,Superio_GPIO_Port + 66h mov al,00h out dx,al .model small .486p .stack 256 .data SCH3114_IO EQU 800h .code org 100h .
PAGE 109
;bit [1:0]=Reserved ;bit [6:2]Reserve=00000 ;bit [7] WDT time-out Value Units Select ;Minutes=0 (default) Seconds=1 ;=================================================== = mov dx,SCH3114_IO + 65h ; mov al,080h out dx,al ;=================================================== = ;66H ;WDT timer time-out value ;bit[7:0]=0~255 ;=================================================== = mov dx,SCH3114_IO + 66h mov al,01h out dx,al ;=================================================== = ;bit[0] status bit R/W ;WD timeout o
PAGE 110
out dx,al .exit END PCM-9375 User Manual 88 Data Modul AG - www.data-modul.
PAGE 111
DI SPLAYS AND EMBEDDED SOLUTIONS DI SPLAYS AND EMBEDDED SOLUTIONS DATA MODUL Headquarters Munich Landsberger Str. 322 D-80687 Munich - Germany Phone: +49-89-56017-0 Fax: +49-89-56017-119 www.data-modul.com Sales Office Hamburg Borsteler Chaussee 51 D-22453 Hamburg - Germany Phone: +49-40-42947377-0 Sales Office Duesseldorf Fritz-Vomfelde-Str.