LV-651 Mini-ITX Motherboard User’s Manual Edition 1.
LV-651User’s Manual Copyright Copyright 2006. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer.
LV-651User’s Manual Packing List Please check the package before you starting setup the system Hardware: LV-651 series motherboard x 1 Cable Kit: 40pin 44pin 44pin 44-pin ATA33 IDE Cable x 1 COM port Cable x1 I/O Shield Cable x 1 Power Cable x 1 Floppy Cable x 1 Printed Matters: User’s Manual x 1 Driver CD x 1
LV-651User’s Manual Index Chapter 1 ………………………………………………………………7 1.1 …………………………………………………………..7 1.2 ............................................................................8 1.3 ........................................................................ …10 1.4 .....................................................................................11 Chapter 2＜Hardware Setup＞………………………………………………………12 2.
LV-651User’s Manual 2.14.2 …………………………………….….32 2.14.3 ………………………………………………….33 2.15 ………………………………………………….34 Chapter 3 …………………………………………………………….37 Appendix A ………………………………………….38 A.1 …………………………………………………………………..38 A.2 ……………………………………………………………….40 A.3 ………………………………………………………………..40 A.4 < CRT Port >………………………………………………………………..41 A.5 …………………………………………………………………41 A.
LV-651User’s Manual (The Page is Left For Blank)
LV-651 User’s Manual Introduction Chapter 1 1.1 LV-651 is the Mini-ITX motherboard with AMD Geode LX800 platform, with onboard VGA, AC97 audio, Giga LAN interface. Based on the AMD Geode LX800 processor, the board provides many advanced features for reduced power consumption, fanless design and high cost/price rate of production. Low Power Consumption Based on the AMD Geode LX800@500MHz processor onboard, it only takes up to 3.
LV-651 User’s Manual Introduction 1.2 General Specification Form Factor CPU Mini -ITX motherboard Embedded AMD Geode LX800 500MHz Fanless with heat sink only Memory One 184-pin DDR DIMM socket support up to 1GB DDR SDRAM Chipset BIOS Green Function Watchdog Timer Real Time Clock Enhanced IDE Optional on board 256M DDR SDRAM Unbufferred, none-ECC memory supported only AMD LX800 and CS5536 Phoenix-Award v6.
LV-651 User’s Manual Connector Introduction Full duplex, IEEE802.3U compliant One External RJ45 connector with LED on rear I/O panel Audio Interface Chipset Realtek ® ALC203 AC97 Audio compliance Interface 2 channels sound output Connector External Audio phone jack for Line-out, Line-in, MIC-in. Onboard audio connector with pin header Onboard CD-IN connector Expansive Interface PCI One Mini-PCI socket for TYPE III. Bus master. 2nd Bus master is shared with Mini-PCI.
LV-651 User’s Manual Introduction 1.
LV-651 User’s Manual Introduction 1.4 1 x 184-pin DDR DIMM VGA monitor Up to 1GB LX800 TFT/LVDS LCD PCI/33Mhz AC97 Audio IEEE1394 CompactFlash＆IDE CS5536 4 x USB2.
LV-651 User’s Manual Hardware Setup Chapter 2 2.
LV-651 User’s Manual Hardware Setup 2.
LV-651 User’s Manual Hardware Setup 2.3 2.3.
LV-651 User’s Manual Hardware Setup 2.4 2.4.1 The board integrates AMD Geode LX800 500MHz processor with special design for power appliance. It requires only 3.8W power consumption at most, and is totally designed for fanless system. 2.4.2 The board supports one 184-pin DDR266/333 SDRAM up to 1GB of capacity, and supports non ECC unbufferred memory modules.
LV-651 User’s Manual Hardware Setup 2.5 The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
LV-651 User’s Manual Hardware Setup 2.6 The board has one Ultra DMA33 IDE interface to support up to 2 ATAPI devices, and one Compact Flash Type II socket on the solder side.
LV-651 User’s Manual Hardware Setup 2.7 The board provides a slim type floppy port; please use the 26-pin FPC cable in the package to connect the floppy device. FDD Floppy rear side 1. 18 4. Lift up this plastic bar 5. Slot the cable in (Blue paste for outside) 6. Press back the plastic bar Lift up the brown plastic bar 2. Slot the cable in (Blue paste for 3.
LV-651 User’s Manual Hardware Setup 2.8 The board integrates with one Realtek RTL8110S-32 Gigabit Ethernet controller. The Realtek RTL8110S-32 supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported. USB_RJ45 2.9 The board integrates AMD Geode LX800 processor with built-in 2D video engine, to provide onboard DB15 VGA connector, 24-bit TFT and 18-bit/24-bit LVDS interface.
LV-651 User’s Manual Hardware Setup 2.9.2 The board provides one 40-pin LVDS connector for 18-bit single channel panel, supports up to 1024 x 768 of resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting Connector: CN_INV Connector model: JST B5B-XH-A Type: 5-pin LVDS Power Header Pin 1 2 3 4 5 Description +12V GND GND GND ENABKL Connector: JVLCD Type: 3-pin Power select Header Pin 1 2 3 Description VCC(5V) LCDVCC VCC3(3.
LV-651 User’s Manual Hardware Setup Connector: CN_LVDS ( for 24bit Single channel LVDS panel ) Type: 40-pin header (40 x 2 pitch 2.0 mm) Connector model: Hirose DF13- 40DP-1.
LV-651 User’s Manual Hardware Setup Connector: CN_LVDS ( for 18bit Single channel LVDS panel ) Type: 40-pin header (40 x 2 pitch 2.0 mm) Connector model: Hirose DF13-40DP-1.
LV-651 User’s Manual Connector: CN_LCD Type: onboard 2 x 20-pin header with housing, pitch=2.
LV-651 User’s Manual To setup the LCD, you need the component below: 1. A panel with LVDS interfaces. 2. An inverter for panel’s backlight power. 3. A LCD cable and an inverter cable. Hardware Setup For the cables, please follow the pin assignment of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables. LCD Installation Guide: 1.
LV-651 User’s Manual Hardware Setup After setup the devices well, you need to select the LCD panel type in the BIOS.
LV-651 User’s Manual Hardware Setup 2.10 The board provides the onboard AC97 2 channel audio interface with Realtek ALC203. Connector: CN_AUDIO Type: 10-pin (2 x 5) 2.54mm x 2.54mm-pitch header Pin Description Pin Description 1 LIN_L 2 Ground 3 LIN_R 4 MIC 2 5 MIC 2 6 Ground 7 N/C 8 FRONTL 9 FRONTR 10 Ground Connector: CDIN Type: 4-pin header (pitch = 2.
LV-651 User’s Manual Hardware Setup 2.11 Based on AMD CS5536, the board provides 2 x USB2.0 ports. The USB2.0 interface provides up to 480Mbps of transferring rate. Interface USB2.0 Controller CS5536 Transfer Rate Up to 480Mb/s Output Voltage 500mA 10 CN_USB1/2 1 USB USB2.
LV-651 User’s Manual Connector: CN_USB Type: 10-pin (5 x 2) header for USB1/2 Ports Pin Description Pin 1 VCC 2 3 Data04 5 Data0+ 6 7 Ground 8 9 Ground 10 Hardware Setup Description VCC Data1Data1+ Ground N/C P.S : The USB2.0 will be only active when you connecting with the USB2.0 devices, if you insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The transferring rate of USB2.0 as 480Mbps is depending on device capacity, exact transferring rate may not be up to 480Mbps.
LV-651 User’s Manual Hardware Setup 2.12 The board provides a programmable 8-bit digital I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK. Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.
LV-651 User’s Manual Hardware Setup 2.
LV-651 User’s Manual Hardware Setup JCSEL1 JCSEL2 RS-232 1 2 5 6 3 12 1 10 RS-485 RS-422 Serial Port Jumper Setting 31
LV-651 User’s Manual Hardware Setup 2.14 The LV-651 provides a standard ATX power supply with 20-pin ATX connector, and the board provides one 4-pin P4 additional use power connector for internal power supply and one 3-pin cooler fan connector for system . 2.14.1 Connector: ATX Type: 20-pin ATX power connector PIN assignment 1 3.3V 2 3.3V 3 GND 4 5V 5 GND 6 5V 7 GND 8 5V 9 5V 10 12V 11 12 13 14 15 16 17 18 19 20 3.3V -12V GND PS_ON GND GND GND -5V 5V 5V 2.14.
LV-651 User’s Manual Hardware Setup 2.14.
LV-651 User’s Manual Hardware Setup 2.15 The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis. Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.
LV-651 User’s Manual (This Page is Left For Blank 35
LV-651 User’s Manual BIOS Setup Chapter 3 The motherboard uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
LV-651 User’s Manual (This Page is Left for Blank) 37
LV-651 User’s Manual I/O Port Pin Assignment Appendix A A.
LV-651 User’s Manual I/O Port Pin Assignment A.2 Connector: FDD Type: 26-pin connector Pin Description 1 VCC 3 VCC 5 VCC 7 DRV1 9 MTR1 11 RPM 13 N/C 15 Ground 17 Ground 19 N/C 21 N/C 23 Ground 25 Ground Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 Description INDEX DRV0 DSKCHG N/C MTR0 DIR STEP WRITE DATA WRITE GATE TRACK 0 WRPTR RDATASEL A.
LV-651 User’s Manual I/O Port Pin Assignment A.4 6 1 2 3 4 5 Connector: CRT Type: 15-pin D-sub female connector on I/O Panel 11 12 13 14 10 Pin 1 2 3 4 5 Description RED GREEN BLUE N/C Ground Pin 6 7 8 9 10 Description Ground Ground Ground LVGA5V Ground Pin 11 12 13 14 15 Description N/C 5VCDA HSYNC VSYNC 5VCLK A.5 Connector: RJ45 Type: RJ45 connector with LED on I/O Panel Pin Description 1 2 3 4 MI0+ MI0- MI1+ MI2+ 5 6 MI2- MI1- 7 8 MI3+ MI3- A.
LV-651 User’s Manual I/O Port Pin Assignment A.7 Connector: Keyboard Type: 6-pin Mini-DIN connector on bracket Pin Description 1 N/C 2 KB_CK 3 4 5 3 BVCC 4 IOGND 6 5 N/C 6 KB_DT 1 Connector: Mouse Type: 6-pin Mini-DIN connector on bracket 3 4 5 Pin Description 1 N/C 2 MS_CK 2 3 BVCC 4 IOGND 5 N/C 6 6 MS_DT A.
LV-651 User’s Manual (This Page is Left for Blank) 42
LV-651 User’s Manual Flash BIOS Appendix B B.1 BIOS Auto Flash Tool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below: http://www.award.com TU UT T File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS. B.2 Flash Method 1. Please make a bootable floppy disk. 2. Get the last .
LV-651 User’s Manual System Resources Appendix C C1.
LV-651 User’s Manual I/O Port Address Map System Resources 45
LV-651 User’s Manual System Resources C2.
LV-651 User’s Manual System Resources C3.
LV-651 User’s Manual Watch Dog timer Setting Appendix D The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
LV-651 User’s Manual (This Page is Left for Blank) 49
LV-651 User’s Manual Contact Information Contact Information Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business. Annso Technology Co.,LTD Address The south faces industry area of Xia Gang Fu Hai road, Chang'an Town,Dongguan City, Guangdong, China 50 TEL +86-769-81666306 FAX +86-769-81666306 Website http://www.annso.com E-Mail sales@annso.com.
