LE-363 3.5 inch Embedded Motherboard User’s Manual Edition 1.
LE-363 User’s Manual Copyright Copyright 2004 - 2005. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products. This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer.
LE-363 User’s Manual Packing List Please check the package before you starting setup the system Hardware: LE-363 little board x 1 Cable Kit: 44-pin 40-pin 44-pin 44-pin ATA33 IDE Cable x 1 COM port & Printer Port Cable x 1 USB Cable x 1 PS/2 keyboard & mouse cable x 1 Audio Cable x 1 Floppy Cable x 1 1 to 3 power output cable Other Accessories: Divers CD (including User’s Manual) x 1 Printed User’s Manual x 1 3
LE-363 User’s Manual Index Chapter 1 ...............................................................6 1.1 ......................................................................6 1.2 .................................................................7 1.3 ..................................................................9 1.4 .........................................................................
LE-363 User’s Manual A.2 ..............................................................................34 A.3 .................................................................................34 A.4 < VGA Port >...............................................................................34 A.5 ................................................................................35 A.6 .................................................................................
LE-363 User’s Manual Introduction Chapter 1 1.1 LE-363 is the 3.5 inches embedded motherboard with AMD Geode GX533 platform, with onboard VGA, AC97 audio, dual LAN and DC 12V input interface. Based on the AMD Geode GX533 processor, the board provides many advanced features for reduced power consumption, fanless design and high cost/price rate of production. Low Power Consumption Based on the AMD Geode GX533@400MHz processor onboard, it only takes up to 8.
LE-363 User’s Manual Introduction 1.2 General Specification Form Factor CPU Memory Chipset USB Port BIOS Green Function Watchdog Timer Real Time Clock Enhanced IDE 3.5 inches embedded motherboard Embedded AMD Geode GX533 400MHz Fanless with heatsink only 1 x 200-pin DDRSO-DIMM up to 512MB Unbufferred, none-ECC memory supported only AMD Geode CS5535 Two internal USB1.1 ports Phoenix-Award PnP flash BIOS Power saving mode includes doze, standby and suspend modes. ACPI version 1.
LE-363 User’s Manual Introduction Ethernet Interface Controller Type Connector Dual PCI based REALTEK 8100B controller 10Base-T / 100Base-TX, auto-switching Fast Ethernet Full duplex, IEEE802.
LE-363 User’s Manual Introduction 1.
LE-363 User’s Manual Introduction 1.4 AMD Geode GX533 Processor VGA monitor TTL/LVDS LCD DDR SO-DIMM up to 512MB PCI/33Mhz Ultra DMA33 IDE USB1.
LE-363 User’s Manual Hardware Setup Chapter 2 2.
LE-363 User’s Manual Hardware Setup 2.
LE-363 User’s Manual Hardware Setup 2.3 2.3.
LE-363 User’s Manual Hardware Setup 2.4 2.4.1 The board integrates AMD Geode GX533 400MHz processor with special design for power appliance. It requires only 8.4W power consumption at most, and is totally designed for fanless system. 2.4.2 Based on AMD GX533 processor with built-in memory controller, the board provides one 200-pin DDR SO-DIMM socket support up to 512MB of capacity.
LE-363 User’s Manual Hardware Setup 2.5 The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
LE-363 User’s Manual Hardware Setup 2.6 The board supports one Ultra DMA33 IDE interface, dual channel for 2 ATAPI devices. The board also provides a Compact Flash Type I socket on secondary IDE channel and one onboard type I/II PCMICA Card Bus on the solder side.
LE-363 User’s Manual Hardware Setup 2.7 The board provides a slim type floppy port; please use the 26-pin ribbon cable in the package to connect the floppy device. FDD Floppy rear side 1. Floppy Port 4. Lift up this plastic bar 5. Slot the cable in (Blue paste for outside) 6. Press back the plastic bar Lift up the brown plastic bar 2. Slot the cable in (Blue paste for 3.
LE-363 User’s Manual Hardware Setup 2.8 The board integrates two PCI based Ethernet controller with REALTEK 8100B, full compliance with IEEE 802.3u 100Base-T specifications and IEEE 802.3x Full Duplex Flow Control.
LE-363 User’s Manual Hardware Setup 2.9 The board integrates AMD Geode GX533 processor with built-in 2D video engine, to provide onboard DB15 VGA connector, 24-bit TTL and 18-bit/24-bit LVDS interface.
LE-363 User’s Manual Hardware Setup In order to setup the LCD display well, please check the jumper setting before you use. Jumper: JVLCD Type: onboard 3-pin header JVOLT 1-2 2-3 Default setting Mode +5V +3.
LE-363 User’s Manual Hardware Setup Connector: CN_LVDS ( for 24bit Signal channel LVDS panel ) Type: 40-pin header (40 x 2 pitch 2.0 mm) Connector model: Hirose DF13- 40DP-1.
LE-363 User’s Manual Hardware Setup Connector: CN_LVDS ( for 18bit Signal channel LVDS panel ) Type: 40-pin header (40 x 2 pitch 2.0 mm) Connector model: Hirose DF13-40DP-1.
LE-363 User’s Manual Hardware Setup Connector: CN_LCD Type: onboard 2 x 20-pin header with housing, pitch=2.
LE-363 User’s Manual Hardware Setup LCD Installation Guide: 1. Preparing the LE-363, LCD panel and the backlight inverter. 2. Please check the datasheet of the panel to see the voltage of the panel, and set the 3. If your panel is for TTL interface, you would need a TTL type cable. jumper JVLCD to +5V or +3.3V. Board side Panel side For sample illustrator only 4. IF your panel is for LVDS interface, you would need a LVDS type cable. Board side Panel side For sample illustrator only 5.
LE-363 User’s Manual Hardware Setup After hardware setup well, you need to select the panel type in the BIOS.
LE-363 User’s Manual Hardware Setup 2.10 The board provides onboard AC97 audio interface with REALTEK ALC201A codec. Please use attached audio cable in the package to have Line-out, Line-in and MIC-in interfaces. Connector: CN_AUDIO Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header Pin Description Pin Description 1 Line – Right 2 Ground 3 Line – Left 4 MIC 5 MIC 6 Ground 7 N/C 8 Line Out – Left 9 Line Out – Right 10 Ground Connector: CDIN Type: 4-pin header 2.
LE-363 User’s Manual Hardware Setup 2.11 The board provides one RS232 COM port on real I/O panel with DB9 as COM1, onboard CN_COM2 RS232 serial port and one onboard parallel connector.
LE-363 User’s Manual Hardware Setup 2.12 The board offers 8-bit digital I/O to customize its configuration to your control needs. For example, you may configure the digital I/O to control the opening and closing of the cash drawer or to sense the warning signal from a tripped UPS. The following is a detailed description of how the digital I/O is controlled via software programming. Connector: CN_DIO Type: 12-pin (6 x 2) 1.27mm x 2.
LE-363 User’s Manual Hardware Setup 2.13 2.13.1 The board requires DC 12V input with onboard DC jack or 4-pin 12V DC connector. Connector: CN_12V Type: 4-pin standard ATX2.0 +12V power connector Pin Description Pin Description 1 Ground 2 Ground 3 +12V 4 +12V 2.13.2 The board also provides one 4-pin connector with +5V/+12V output.
LE-363 User’s Manual Hardware Setup 2.14 The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis. Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.
LE-363 User’s Manual BIOS Setup Chapter 3 The single board computer uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
LE-363 User’s Manual (This Page is Left For Blank) 32
LE-363 User’s Manual I/O Pin Assignment Appendix A A.
LE-363 User’s Manual A.2 Connector: FDD Type: 26-pin connector Pin Description 1 3 5 7 9 11 13 15 17 19 21 23 25 VCC VCC VCC N/C N/C RPM N/C Ground Ground Ground N/C Ground Ground Pin Description 2 4 6 8 10 12 14 16 18 20 22 24 26 INDEX DRX DSKCHG N/C MTR0 DIR STEP WRITE DATA WRITE GATE TRACK 0 WRX RDATASEL A.3 5 Connector: CN_IR Type: 5-pin header for SIR Ports Pin Description 1 Vcc 2 N/C 3 IRRX 4 Ground 5 IRTX 6 A.
LE-363 User’s Manual I/O Pin Assignment A.5 Connector: COM1 Type: 9-pin D-sub male connector on bracket Pin Description Pin 1 DCD 6 2 RXD 7 3 TXD 8 4 DTR 9 5 Ground 1 2 3 4 5 Description DSR RTS CTS -XR A.6 1 Connector: RJ45_1/2 Type: RJ45 connector with LED on bracket Pin Description 1 TX+ 2 TX- 3 RX+ 4 RX- 8 5 N/C 6 N/C 7 N/C A.
LE-363 User’s Manual A.
LE-363 User’s Manual Flash BIOS Appendix B B.1 BIOS Auto Flash Tool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below: http://www.award.com File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS. B.2 Flash Method 1. Please make a bootable floppy disk. 2. Get the last .bin files you want to update and copy it into the disk. 3.
LE-363 User’s Manual (This Page is Left For Blank) 38
LE-363 User’s Manual System Resources Appendix C C.
LE-363 User’s Manual 40
LE-363 User’s Manual System Resources C.
LE-363 User’s Manual Contact Information C.3 C.3.1 .C.3.
LE-363 User’s Manual System Resources Appendix D The GPIO can be programmed with the MSDOS debug program using simple IN/OUT commands. The following lines show an example how to do this. GPIO0...
LE-363 User’s Manual Contact Information Appendix E The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
