User guide
Table Of Contents
- Title Page
- Table of Contents
- About this User Guide
- Introducing the 3ware® SATA RAID Controller
- Getting Started with Your 3ware RAID Controller
- First-Time RAID Configuration Using 3BM
- Driver Installation
- Driver Installation Under Windows
- Driver Installation Under Linux
- Obtaining 3ware Linux Drivers
- Driver Installation Under Red Hat Linux or Fedora Core 5
- Materials required
- Creating a Red Hat Linux Driver Diskette
- Installing the 3ware Kernel Driver Module while Installing Red Hat Linux on a New Unit
- Installing the 3ware Kernel Driver Module on a Red Hat or Fedora Core Linux System that Boots From a Different Device
- About Variables In the Kernel Driver Module Installation Instructions
- Driver Installation Under SuSE Linux
- Compiling a 3ware Driver for Linux
- Driver Installation Under FreeBSD
- 3ware BIOS Manager 2 (3BM 2) Introduction
- 3DM 2 (3ware Disk Manager) Introduction
- Configuring Your Controller
- Configuring Units
- Configuring a New Unit
- Creating a Hot Spare
- Naming a Unit
- Setting Unit Policies
- Changing An Existing Configuration by Migrating
- Deleting a Unit
- Removing a Unit
- Moving a Unit from One Controller to Another
- Adding a Drive
- Removing a Drive
- Rescanning the Controller
- Maintaining Units
- Checking Unit and Drive Status through 3DM
- About Degraded Units
- About Inoperable Units
- Alarms, Errors, and Other Events
- Background Tasks
- Scheduling Background Tasks
- Locating a Drive by Blinking Its LED
- Maintaining Your Controller
- Determining the Current Version of Your 3ware Driver
- Updating the Firmware and Driver
- Downloading the Driver and Firmware
- Updating the Firmware Through 3DM 2
- Updating the 3ware Driver and Firmware Under Windows
- Using the Update Utility With Multiple Controllers
- Updating the 3ware Driver Under Windows XP
- Updating the 3ware Driver Under Red Hat or Fedora Core
- Updating the 3ware Driver Under SuSE
- Updating the 3ware Driver Under FreeBSD
- Updating the Firmware Under Linux and FreeBSD
- Viewing Battery Information
- Testing Battery Capacity
- 3DM 2 Reference
- Troubleshooting
- Appendices
- Index
16 3ware Serial ATA RAID Controller User Guide
2
Getting Started with Your
3ware RAID Controller
Setting up your 3ware RAID controller involves these main steps:
• Physically Install the RAID Controller and Drives
• Configure a RAID Unit
• Install the Driver and Make the Operating System Aware of the New
Drives
• Set Up Management and Maintenance Features
Once the controller and drives have been physically installed, the order in
which you perform these steps depends in part on whether one of the units
you configure will act as your boot drive.
Tip: When you are first setting up your system, you may want to review
“System Requirements” on page 2.
Physically Install the RAID Controller and Drives
To install your controller, follow the instructions in the installation guide that
came with your 3ware controller. If you do not have a hardcopy of the
installation manual, it is available in the “doc” folder on your 3ware CD, or
you can download it from the 3ware website at http://www.3ware.com/
support/userdocs.asp.
For drive installation, see the instructions that came with your 3ware Sidecar
or other external enclosure. If you are installing drives in a computer case,
follow the manufacturer’s instructions.
Configure a RAID Unit
If you would like more information about what RAID level to choose for your
situation, review the information under “Understanding RAID Concepts and
Levels” on page 4. Then turn to “Configuring a New Unit” on page 91.
If you want to install the operating system on and boot from a drive managed
through the new 3ware RAID controller, use the 3ware BIOS Manager (3BM)
to define the configuration. You will find step-by-step instructions for initial