User guide
Table Of Contents
- Title Page
- Table of Contents
- About this User Guide
- Introducing the 3ware® SATA RAID Controller
- Getting Started with Your 3ware RAID Controller
- First-Time RAID Configuration Using 3BM
- Driver Installation
- Driver Installation Under Windows
- Driver Installation Under Linux
- Obtaining 3ware Linux Drivers
- Driver Installation Under Red Hat Linux or Fedora Core 5
- Materials required
- Creating a Red Hat Linux Driver Diskette
- Installing the 3ware Kernel Driver Module while Installing Red Hat Linux on a New Unit
- Installing the 3ware Kernel Driver Module on a Red Hat or Fedora Core Linux System that Boots From a Different Device
- About Variables In the Kernel Driver Module Installation Instructions
- Driver Installation Under SuSE Linux
- Compiling a 3ware Driver for Linux
- Driver Installation Under FreeBSD
- 3ware BIOS Manager 2 (3BM 2) Introduction
- 3DM 2 (3ware Disk Manager) Introduction
- Configuring Your Controller
- Configuring Units
- Configuring a New Unit
- Creating a Hot Spare
- Naming a Unit
- Setting Unit Policies
- Changing An Existing Configuration by Migrating
- Deleting a Unit
- Removing a Unit
- Moving a Unit from One Controller to Another
- Adding a Drive
- Removing a Drive
- Rescanning the Controller
- Maintaining Units
- Checking Unit and Drive Status through 3DM
- About Degraded Units
- About Inoperable Units
- Alarms, Errors, and Other Events
- Background Tasks
- Scheduling Background Tasks
- Locating a Drive by Blinking Its LED
- Maintaining Your Controller
- Determining the Current Version of Your 3ware Driver
- Updating the Firmware and Driver
- Downloading the Driver and Firmware
- Updating the Firmware Through 3DM 2
- Updating the 3ware Driver and Firmware Under Windows
- Using the Update Utility With Multiple Controllers
- Updating the 3ware Driver Under Windows XP
- Updating the 3ware Driver Under Red Hat or Fedora Core
- Updating the 3ware Driver Under SuSE
- Updating the 3ware Driver Under FreeBSD
- Updating the Firmware Under Linux and FreeBSD
- Viewing Battery Information
- Testing Battery Capacity
- 3DM 2 Reference
- Troubleshooting
- Appendices
- Index
Chapter 8. Configuring Units
124 3ware Serial ATA RAID Controller User Guide
Removing a Unit Through 3DM
In 3DM, the command for deleting a unit is on the Maintenance page. Be
sure to follow steps 1 and 2 in the instructions before using the Remove
command.
To remove a unit through 3DM
1 Make sure the operating system is not accessing the unit you want to
remove.
For example, make sure you are not copying files to the unit, and make
sure that there are no applications with open files on that unit.
2 Unmount the unit.
This step is very important. If a unit is not unmounted and you remove
it, it is the equivalent of physically yanking a hard drive out from under
the operating system. You could lose data, the system could hang, or the
controller could reset.
Under Windows, go to
Start > Administrative Tools > Computer
Management
, and select Disk Management. Remove the logical drive
letter for the unit.
Under Linux and FreeBSD, you can unmount the unit with this command:
umount <mount location>
3 In 3DM, choose Management > Maintenance.
4In the
Unit Maintenance table on the Maintenance page, select the unit
you want to remove and click
Remove Unit.
5 When a message asks you to confirm, click OK.
The unit number and information is removed from the
Maintenance page
in 3DM.
Note: You can also remove a drive, if you want to force a degrade on a redundant
unit, or if you want to remove a drive from the “Available Drives” list so that you can
then remove it from the system. For more information, see “Removing a Drive” on
page 130.
Note: If you do not have hot swap carriers, you do not need to
remove a unit via 3DM. Simply power down the system and remove
the applicable drives. Refer to your system’s user guide for details on
removing fixed disks. If you do have hot swap carriers, follow the
steps below.