User guide
Table Of Contents
- Title Page
- Table of Contents
- About this User Guide
- Introducing the 3ware® SATA RAID Controller
- Getting Started with Your 3ware RAID Controller
- First-Time RAID Configuration Using 3BM
- Driver Installation
- Driver Installation Under Windows
- Driver Installation Under Linux
- Obtaining 3ware Linux Drivers
- Driver Installation Under Red Hat Linux or Fedora Core 5
- Materials required
- Creating a Red Hat Linux Driver Diskette
- Installing the 3ware Kernel Driver Module while Installing Red Hat Linux on a New Unit
- Installing the 3ware Kernel Driver Module on a Red Hat or Fedora Core Linux System that Boots From a Different Device
- About Variables In the Kernel Driver Module Installation Instructions
- Driver Installation Under SuSE Linux
- Compiling a 3ware Driver for Linux
- Driver Installation Under FreeBSD
- 3ware BIOS Manager 2 (3BM 2) Introduction
- 3DM 2 (3ware Disk Manager) Introduction
- Configuring Your Controller
- Configuring Units
- Configuring a New Unit
- Creating a Hot Spare
- Naming a Unit
- Setting Unit Policies
- Changing An Existing Configuration by Migrating
- Deleting a Unit
- Removing a Unit
- Moving a Unit from One Controller to Another
- Adding a Drive
- Removing a Drive
- Rescanning the Controller
- Maintaining Units
- Checking Unit and Drive Status through 3DM
- About Degraded Units
- About Inoperable Units
- Alarms, Errors, and Other Events
- Background Tasks
- Scheduling Background Tasks
- Locating a Drive by Blinking Its LED
- Maintaining Your Controller
- Determining the Current Version of Your 3ware Driver
- Updating the Firmware and Driver
- Downloading the Driver and Firmware
- Updating the Firmware Through 3DM 2
- Updating the 3ware Driver and Firmware Under Windows
- Using the Update Utility With Multiple Controllers
- Updating the 3ware Driver Under Windows XP
- Updating the 3ware Driver Under Red Hat or Fedora Core
- Updating the 3ware Driver Under SuSE
- Updating the 3ware Driver Under FreeBSD
- Updating the Firmware Under Linux and FreeBSD
- Viewing Battery Information
- Testing Battery Capacity
- 3DM 2 Reference
- Troubleshooting
- Appendices
- Index
Deleting a Unit
www.3ware.com 121
If you have incomplete drives, or drives that appear with a message such as
“Unsupported DCB,” indicating that they were previously part of a unit on a
3ware 7000/8000 series controller, they must be deleted before you use them.
(If you want to move a unit from a 7/8000 controller to a 9000 series
controller, you must convert the drives first. For more information, see
“Moving a Unit from One Controller to Another” on page 126.)
Deleting a Unit through 3DM
In 3DM, the command for deleting a unit is on the Maintenance page. Be
sure to follow steps 1 through 3 in the instructions before using the Delete
command.
To delete a unit through 3DM
1 Make sure the operating system is not accessing the unit you want to
remove.
For example, make sure you are not copying files to the unit, and make
sure that there are no applications with open files on that unit.
2 Backup any data you want to keep.
3 Unmount the unit.
This step is very important. If a unit is not unmounted and you delete it,
it is the equivalent of physically yanking a hard drive out from under the
operating system. You could lose data, the system could hang, or the
controller could reset.
Under Windows, go to
Start > Administrative Tools > Computer
Management
, and select Disk Management. Remove the logical drive
letter for the unit.
Under Linux and FreeBSD, you can unmount the unit with this command:
umount <mount location>
4 In 3DM, choose Management > Maintenance.
Warning: When a unit is deleted, all of the data on that unit will be lost. The drives
cannot be reassembled into the same unit because the data on it is erased. If you
want to reassemble the drives into the same unit on another controller, use the
Remove Unit button in 3DM instead of the
Delete Unit button. Or, if you’re at the
BIOS level already, you can shut down the computer and physically move the drives
to another 3ware 9000 series RAID controller. When you restart your system, the
controller will recognize the unit. For more information see “Moving a Unit from One
Controller to Another” on page 126.