User's Guide
©2021 EntryLogic. All Rights Reserved. EntryLogic™ is a trademark of EntryLogic, Inc.
TP450 User Guide
www.entrylogic.com
Bluetooth printer
Bluetooth: It is a kind of technology with short distance wireless connection which
globally used, using the same 2.4GHz nearby free charge and free application for
frequency radio range with microwave. It can transfer data without alignment, with an
effective transmission range of 10m. The Bluetooth printer carries out data transmission
by matching with the Bluetooth device, the receiving master transfers the data to the
printer and print it out. Hand-held terminal with Bluetooth interface, laptop and other
information terminals could print via Bluctooth interface.
Mini receipt printer compatible with Bluetooth 2.1 standard, with the power level of
CLASS 2, and effective transmission distance is 10m. The name of the device is Printer
001, the initial password is "123456". Users may change the name of the device and
the password if necessary.
The Bluetooth printer need to be paired with the main device of Bluetooth before
working, the process of pairing will be started by the main device.
For detail pairing method, please refer to the function instructions for main device
of Bluetooth. When pairing, the Bluetooth printer should power on.
Note: If the name of the printer is not changed, please do not power on other
printers at the same time when pairing, otherwise it cannot identify which
printer is paired successfully.
Bluetooth printer setting
1. Connect the printer with computer, turn on the printer. Open the "tools" folder in printer
CD, find the printer setting tools, choose the port and print a test page, if works, then enter
into "Advanced" option.
Note: Bluetooth printer and the port setting procedures: firstly connect the power
and run on the Bluetooth printer, connect the Bluetooth device to USB interface of
the computer (master), a Bluetooth icon at the lower right corner on the desktop
will appear.
2. Click "Bluetooth setting", set the related information such as the name of the
Bluetooth device and the password, then click "Setting". The printer will "beep" a sound.
Then restart the computer and check if the information of the self-test page printed matches
with the settings.
3. Enter "Control Panel" -- "Hardware and Sound" -- "Add a Blue tooth device" (Computer
should support Bluetooth function.
4. Default name of Bluetooth setting. Choose "Printer001", click "Next".
5. Choose "Enter the device's pairing code", enter the pass word" 123456", add the device.
6. Aer adding the device, choose "Equipment and printer", find the added Bluetooth device
Printer001, click the properties of hardware, check the port infonnation of the device.
7. Aer installing the printer driver, find the icon of driver, check the properties of it, choose
the right port and print a test page via driver.
FCC and ISED Canada Compliance: This equipment has been tested and is in compliance
with Part 15 of the FCC Rules and ISED Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC-ID: 2AH6G-TP450
IC-ID: 26745-TP450
The AC Power Adapter has been tested and in compliance with the safety standards set forth
by Part 1: Safety Requirements in both the US [UL 62368-1:2014 Ed.2] and Canada
[CSA C22.2#62369-1:2014 Ed.2].
In accordance to local laws, when the device reaches end of life, it should be recycled in a
manner that protects human health and the environment. Please consult your local authorities
for local laws and regulations regarding the recycling and proper disposal of office electronics.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Statement
To maintain compliance with FCC's RF Exposure guidelines, This equipment
should be installed and operated with minimum distance of 20cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
Specifications & Compliance
ISED Canada Statement:
This device contains licence-exempt tasmittre(s)/receiver(s)/ that comply with Innovation Science and
Economic Development Canada 's licence-exempt RSS(s).
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation
of the device.
Radiation Exposure: This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment
RF Exposure Statement
To maintain compliance with IC's RF Exposure guidelincs, This cquipment should be.installed and
operated with minimum distance of 20cm the radiator your body. This device and its antenna(s) must
not be co-located or operation in conjunction with any other antenna or transmitter
Déclaration de l'ISED Canada :
Cet appareil contient des tasmittre (s) / récepteur (s) sans licence / conformes à l'innovationRSS
exemptes de licence de Sciences et Développement économique Canada. L'opération est sous réserve
des deux conditions
suivantes :
1) cet appareil ne peut pas causer d'interférences et
2) ce dispositif doit accepter toute interférence, y compris peut provoquer le fonctionnement
indésirable de l'appareil.
Exposition aux rayonnements : Cet équipement est conforme aux radiations du Canada limites
d'exposition pour un environnement incontrôlé
noncé d'exposition RF
Pour maintenir le respect des guides d'exposition RF d'IC, cquipment doit être.installé et actionné avec
une distance minimale de 20cm le radiateur de votre corps. Cet appareil et ses antennes ne doivent pas
être co-localisé ou en opération en conjonction avec toute autre antenne ou émetteur