> ELECTRIC FIREPLACES wna itinerant. oom ELECTRIC FIREPLACES SAFETY INFORMATION AND INSTALLATION MANUAL ZEAL-26-2923, ZEAL-30-3226, ZEAL-33-3624, ZEAL-39-4134, ZEAL-2939, INSERT-26-3825, INSERT-30-4026, INSERT-33-4230, ZECL-26-FLUSHMT, ZECL-30-FLUSHMT Read these instructions completely before beginning installation. Failure to follow them could cause a heater malfunction and result in serious injury and/or property damage. WARNING: All electric heaters have hot and arcing or sparking parts inside.
SAFETY INFORMATION Due to high temperatures, the fireplace should be located out of traffic and away from furniture and draperies. Do not place clothing or other flammable material on or near the fireplace. Never place any objects on the fireplace. The fireplace can become very hot when running. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. The fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching.
13. Avoid the use of an extension cord because the extension cord may overheat and cause a fire. If you have to use an extension cord, the cord should be No. 14 AWG minimum size and rated not less than 1875 WATTS. 14. Always use properly grounded fused and polarized outlets. 15. Always use ground fault protection where it is required by electrical daces. 16. Always disconnect the power before performing any cleaning, maintenance or relocation of the heater. 17.
225m 8 347) Aes see apm (437) FORT VIEW SINE BIER a6 an TIF 5027) EEE ETE HE see TOP YIELD Figure 7 ZEAL-39-4134 dimensions mages [23 3/27) 7 er Els Finn £29 2727) 48 fom B yEy FRONT YIF STOW VIEW 615 0 12 307] Ow = BO plaid Figure 8 ZEAL-2939 dimensions
Locating FIREPLACE WARNING: Never locate this heater where it may fall into a bathtub or any water container. NOTICE: Minimum and maximum clearances must be maintained at all times. Illustrations throughout these instructions reflect typical Installations and are for design purposes only. Actual Installations may vary slightly due to individual preferences. Ll Figure 11 Heater Locations Figure 8 illustrates a variety of ways the heater may be located in a room.
APPEALING FRONT LE Sven atom > Figure 12 The minimum distance from the top of the appliance that the mantel can be installed is 5cm, at any depth. The sides and back are 1em. UNPACKING AND TESTING FIREPLACE Carefully remove the unit from the box. Prior to permanently installing the unit, test it to make sure it operates properly. To do this, plug the unit's power supply cord into a 120-volt grounded outset.
A WARNING RISK OF FIRE! The power cord must not be pinched or placed against a sharp edge. Secure the cord to avoid tripping or snagging thus reducing the risk of fire, electric shock or personal Injury. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners or similar items. Arrange the cord away from traffic areas where it could be tripped over. Once the mantel has been prepared, the fireplace can be installed.
1. For remote to function make sure the heater is plugged-in and main power switch located on the upper left hand side behind the front glass is at position |. Figure 15 Figure 16 Note. The heating and flame function can only be operated by the remote control. The remote control needs 2 AA batteries (not included). Note: When the heater Is muted on for the first time, It may release a slight, harmless odor.
as desired. Crass this button again to tum OFF the flame effect. a. The — or + buttons control the brightness of EMBER. To Increase the brightness of ember bed, press and release the + button. Each time you press this button the brightness will increase by a small amount, until the maximum is reached. To decrease the brightness of ember bed, press and release the — button. Each time you press this button the brightness will decrease by small amount, until the minimum brightness is reached. b.
Figure 17 The panel control 1. Power ON/OFF switch, 2. Heat control button, 3. Flame control button, 4. HEATER LED, 5. POWER LED Plug the heater into a suitable outlet 1) “Power ON/OFF" Set this switch to position | to tum the product ON. Setting turn the product OFF. When unit is trued ON the fireplace Power LED will be illuminated. 2) "Heat control button” Press the HEAT button repeatedly to set the heater to desired heat setting. The heater indicator LED will glow which shows the current heater setting.
3) “Flame control button” Press the Flame brightness adjustment button to adjust the flame height and ember bed brightness. Press and release the FLAME control button to cycle through LO, MED, HI and OFF. HARD-WIRE INSTALLATION Warning: ENSURE ALL POWER IS TURNED OFF BEFORE HARD WIRING THIS APPLIANCE. HARD WIRING CONNECTION If it is necessary to hard wire this appliance, a qualified electrician may remove the cord connection, and wire the appliance directly to the house hold wiring.
FIRE GLASS MEDIA INSTALLATION BEFORE YOUR INSTALLATION CLEANING THE MEDIA: The media may contain a fine white dust that needs to be cleaned prior to installation. Clean the media with soap, drain, rinse thoroughly and dry before placing into the tray. Unscrew four screws show In the figure 19. Take RH and LH highlight bracket out. Take out the log. Unplug the LED strip plug. Take the LED strip and the steel bracket out. Choose the color of Fire Glass Media you would like to use.
2. To remove fingerprints or other marks, the glass can be cleaned with a damp cloth using a good quality household glass cleaner. The glass should be completely dried with a lint free cloth or paper towel. 3. In the event of glass breakage, vacuum all remaining glass pieces with a shop vac. DO NOT VACUUM WHILE THE PIECES ARE HOT. Replace glass only with replacement parts made specifically for this heater. Never substitute material. Only fully tempered soda lime safety glass may be used on this heater.
Remark: #15 Not show in upper figure. TROUBLE SHOOTING A WARNING: Turn off the appliance and let it cool before servicing it. Only a qualified service person should service and repair the heater.
Remote control does not week Low Batteries Power switch is in OFF position Replace AA batteries In remote control Turn on the man power switch Heater does not provide heat wham turned on Thermal switch has been tripped. Circuit breaker has been tripped Tum the unit off and unplug the unit for five minutes. Plug back In and tum the unit on. If plug can not be reached, follow directions for tripped circuit breaker Tum off cultural breaker that supplies electricity to the unit .
WARRANTY ‘Mammalian Imports Corp. {“Mantilla) warrants that your newly purchased Mantilla electric fireplace is free from manufacturing and material defects, for a period of one (1) year from the date of the first purchase, subject to the conditions and limitations contained below.
