INSTALLATION AND OPERATION INSTRUCTIONS FOR CUBE‐2025WM SAFETY INFORMATION WARNING If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other li INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
TABLE OF CONTENTS Please read and carefully follow all of the instruction found in this manual. Please pay special attention to the safety instructions provided in this manual. The instructions included here will assure that you have many years of dependable and enjoyable service from your Amantii product. Contents IMPORTANT INSTRUCTIONS .............................................................................................................................3 UNPACKING AND TESTING APPLIANCE ............
IMPORTANT INSTRUCTIONS 1. Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fire or injury. 2. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from the front of the heater; keep them away from sides and rear as well. 3. Always unplug heater when it’s not in use. 4.
UNPACKING AND TESTING APPLIANCE Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet. Test all aspects of its operation (manual switches, remote and heater) to make sure all components operate correctly. As with most electronic devices, your new electric fireplace has been designed to operate at temperatures between 5 (41) and ℉ 35 (95).
CUBE‐2025WM Description Voltage Watts NO HEATER MOTOR HEATER Appliance Width Appliance Height Appliance Depth Gross Weight Plug Location Cord Length BTU ELECTRIC FIREPLACE 230V AC 60Hz 1500W Max 25W 19W 19 5/8" or 50 cm 25 1/4" or 64.1 cm 11 3/4" or 30 cm 50.
INSTALLATION WALL‐MOUNT NOTE: Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance. 1. Select a location that is not prone to moisture and is located at least 0.91 m or 3 feet away from combustible materials such as curtains or drapes, furniture, bedding, paper, etc. 2. Select a suitable position in which to mount the heater horizontally – use a spirit level to achieve this (Fig. 1). Fig. 2 3.
INSTALLATION CUBE‐BASE‐LEGS 1. Screw the base legs to the steel panel. 3. Place the unit onto the base leg and screw and screw in the adjustable feet, fixing the unit and the base leg. 4. You have completed the installation of the CUBE‐BASE‐LEGS. 2. Unscrew the adjustable feet from the bottom of the unit.
INSTALLATION CUBE‐BASE‐SPEAKER 1. Unscrew the adjustable feet from the unit. 3. Place the unit on the CUBE‐BASE‐SPEAKER and screw in the adjustable feet, fixing the unit and the speaker box. 2. Unscrew the rear screws and remove the back steel panel 4. Plug into the back of the unit. Re‐install the back steel panel.
INSTALLATION OUTDOOR CUBE electric fireplaces are suitable for installation in outdoor areas protected from direct water impingement. In addition to maintaining the listed mantel and combustibles clearances, a rain protection overhang factor of 1/2 shall be constructed to the front and to each side of the installed appliance. See illustration below. All wiring connections to line power shall be in accordance with local building code requirements. NOTE: The CUBE Wall Mount Unit is approved for outdoor use.
HARD‐ WIRE INSTALLATION Turn off the appliance completely and let cool before servicing. Only a qualified technician should service and repair this electric appliance. If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the house hold wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence of local codes, use the current CSA C22.
MEDIA OPTIONS Your fireplace shipped with log set and sable glass. STEP 3: Remove the front glass panel to decorate your fireplace. Pour the decorative media into the tray. Feel free to use any combination of fire glass media that you find most appealing. LOG SET SABLE GLASS STEP 4: After finishing decoration, re‐install the front glass panel using the securing screws removed in step 2. MEDIA INSTALLATION STEP 1: Unplug the unit and make sure controls are switched off.
OPERATION The fireplace can be operated either by the switches located on the left front of the fireplace unit or by supplied remote control. MANUAL OPERATION 1. 2. 3. The main power ON/OFF switch in position O, the fireplace is OFF. When main power ON/OFF switch is at position I, the fireplace is ready to use. Press the button repeatedly to set the heater to desired heat setting. The heater indicator LED will glow which shows the current heater settings.
REMOTE CONTROL OPERATION For remote to function make sure the heater is plugged in and main power switch located on the bottom left hand side is at position I. When operating the remote make sure you point the remote to the center of the fireplace and make sure each time you press the button the buzzer inside the unit will beep once. It takes some time for the receiver to respond to the transmitter. Do not PRESS the buttons more than once within two seconds for correct operation.
INSTALLING WALL THERMOSTAT WALL THERMOSTAT WIRING DIAGRAMS Wire the wall thermostat prior to installing the fireplace. WALL THERMOSTAT WIRING (24 VAC) Install Wall Thermostat per instructions provided with kit and per the following information: 1. Turn off circuit breaker. 2. Remove cover plate located on the left side of appliance. 3. Pull the wire out and cut the inside thermostat. Connect the wires to the wall thermostat as shown below. Follow instructions provided with wall switch kit.
REPLACEMENT PARTS This list contains replacement parts NO. PART NUMBER DESCRIPTION QTY.
EXPLODED VIEW i • +' \ \ \ \ \ \ OJ / / / ' . // lD \ 16 \\ \
00 p Q ꞏ oꞏ -q5 0 ' l \ ) J . J .I I L\)J . I - 00 "Q I 1 -/. v J J 00 ꞏ I z >- oo < u 1--1 JJ:-4 UUlUJ < ! ꞏ 00o 00 0 TEMPERATURE SENS R RECEIVER Q JJ:-4 O 0 0 ll illRP TIU • IPl -• Lm. 0 r r 0 00 "•9." BYB+ 1/n"'- C 'U 16 L. BUTT N - :J RBI.AT-Bl P.....a RBI.ATꞏ+ M . ..
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Dim or no flame Flame LED’s are burnt out. Inspect the LED’s and replace them if necessary. Change a flicker and back black cloth. Back black cloth is falling off and rolled up in the flicker. not Ember LED’s are burnt out Ember bed is glowing or dimming Appliance turns off and will not turn on Inspect the ember bed LED’s and replace them if necessary.
SERVICE HISTORY This heater must be serviced annually depending on usage.
WARRANTY FOR PRODUCTS MANUFACTURED AFTER JANUARY 1st, 2016 Amantii Imports Corp. ("Amantii " ) warrants that your newly purchased Amantii electric fireplace is free from manufacturing and material defects for a period of two (2) years from the date of the first purchase, subject to the conditions and limitations contained below.
