PACKAGE HEAT PUMP INSTALLATION INSTRUCTIONS Installer: Affix literature adjacent to the unit. ® is a trademark of Maytag Corporation and is used under license to Goodman Company, L.P. All rights reserved. *NOTE: Please contact your distributor or our website for the applicable product data book referred to in this Part No. 10730420 Printed in USA Goodman Company, L.P. 1810 Wilson Parkway • Fayetteville, Tennessee 37334 www.amana-hac.com ©2004 Goodman Company, L.P.
SAFETY INSTRUCTIONS RECOGNIZE SAFETY SYMBOLS, WORDS, AND LABELS The following symbols and labels are used throughout this manual to indicate immediate or potential safety hazards. It is the owner’s and installer’s responsibility to read and comply with all safety information and instructions accompanying these symbols. Failure to heed safety information increases the risk of personal injury, property damage, and/or product damage.
GENERAL INFORMATION conditioned. The loads should be calculated by an approved method or in accordance with A.S.H.R.A.E. Guide or Manual J - Load Calculations published by the Air Conditioning Contractors of America.
THERMOSTAT WIRING Fork Lift From Back Of Unit When an electric heater is installed, the thermostat wiring will be made at the heater accessory box. If a unit is installed without electric heaters, the low voltage wiring to the blower section can be cut, either in the control box area or in the blower section, to allow splicing-in of field-installed wiring, or connect to terminal strip in unit control box. See the unit wiring diagram for electrical connections.
Low Voltage Terminal Strip CAUTION TO AVOID PROPERTY DAMAGE OR PERSONAL INJURY DUE TO FIRE, USE ONLY COPPER CONDUCTORS. C G Y R W CAUTION ON W1 ON W2 O TO PREVENT IMPROPER AND DANGEROUS OPERATION DUE TO WIRING ERRORS, LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. VERIFY PROPER OPERATION AFTER SERVICING. The best protection for the wiring is the lowest rated fuse or circuit breaker which will supply power to the unit during normal operation without nuisance trips.
require that cover clips (included with the unit) be installed to ensure a secure fit of the Horizontal Duct Covers. 24, 30, 36, 42 AND PHB48 Models: Remove 1. Remove and set aside the four (4) supply air side screws. 2. Remove and set aside the two (2) return air side screws. REMOVE SCREWS REMOVE SCREWS Loosen Duct Removal 3. Remove the clamp securing the blower assembly to the bottom of the unit. Discard clamp and screws. SUPPLY AIR {} Supply Air Side Screws Removal 3.
Even though a return air filter is not supplied with this unit, there must be a means of filtering all return air. Refer to the following table or the Product Data Book applicable to your model* for filter size information. CLIPS MODEL PHB24C02* PHB30C02* PHB36C02* PHB42C02* PHB48C02* PHB60C02* SELF-DRILLING SCREWS Cover Clip Installation 3. Attach 16x16 horizontal covers using screws provided with kit to the outer duct opening flange and cover clip holes. 4.
OPERATING INSTRUCTIONS 1. Turn ON the electrical power supply to the unit. 2. Place the room thermostat selector switch in the COOL or HEAT position (or AUTO if available, and if automatic changeover from cooling to heating is desired). 3. Set the room thermostat to the desired temperature.
ACCESSORIES Horizontal Duct Covers (CHK001A) Single Point Power Connections (SPK**A) Roof Curb - Heat Pump (PRC06A1) Roof Curb - Universal (PRC08A1) Over-Under to Side by Side (PDTROU4A) Over-Under to Side by Side (PDTROU6A) Additional accessories, as described above, can be purchased to fit specific application needs. Accessories can be ordered by the part numbers in the table and each accessory includes its own separate instructions.
WARNING DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WARNING DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WARNING DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. 208 VOLT INSTALLATION Y BLOWER INTERFACE HE AT A B C D A B C D COOL W NORM ( )+ (-) T EST W2 PIN 1 R O A BK 19 VT 20 YL/BK LOWPRESSURE SWITCH(LPS) 8 7 DFT 9 BR-11 DF1 VT 16 90 60 30 DF2 O.D.
WARNING DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WARNING DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. 208 VOLT INSTALLATION AIR CIRCULATION BLOWER (ACB) Y BLOWER INTERFACE HE AT A B C D TO HEATER KIT A S 8 7 DFT 9 YL 12 W 4 G 5 Y 6 O 1 C 2 R DF1 VIEW A-A 90 60 30 DF2 RD BK GN O.D.
WARNING DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WARNING DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. 208 VOLT INSTALLATION CAPACITOR (CAP) GND TRANSFORMER FOR PROPER OPERATION ON 208 VOLT THE FOLLOWING CHANGE MUST BE MADE: MOVE RD6 WIRE FROM TRANSFORMER 230 TERMINAL TO 208 TERMINAL.
WARNING DISCONNECT ELECTRICAL POWER TO THIS UNIT BEFORE SERVICING OR PERFORMING MAINTENANCE. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. 208 VOLT INSTALLATION GND TRANSFORMER FOR PROPER OPERATION ON 208 VOLT THE FOLLOWING CHANGE MUST BE MADE: MOVE RD6 WIRE FROM TRANSFORMER 230 TERMINAL TO 208 TERMINAL.
CLEARANCES WARNING TO AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO FIRE, CLEARANCES TO COMBUSTIBLE SURFACES LISTED AS SHOWN MUST BE OBSERVED.
©2000-2004 Goodman Company, L.P.
