Operating instructions

PREPARE
WINDOW FOR
INSTALLATION
Inspect window track, sash, and sill
for its ability to support the weight of
air conditioner.
Measure width between window
moldings to ensure Instant Mount
window mounting kit will fit window
frame. Instant Mount models are
designed for windows from 24 to
34 wide.
Instant Mount kit supplied with unit
is designed for mounting in most
double-hung windows without
storm windows. For installation in
window frame with storm window,
modify sill by adding wood strips to
inner and outer sills. This raises unit
and eliminates interference of storm
window frame.
3
Mobile home window installation
Add wood strip (at least 1 1/2 wide)
along entire width of window sill.
Thickness of wood strip should match
height of front lip on window frame.
Fasten wood strip to sill with a
minimum of three countersunk wood
screws (not supplied with kit). This
provides a smooth surface for
mounting air conditioner.
Storm window installation
If storm window frame does not allow
adequate clearance below sill (1/2
required), remove storm window
frame or create clearance by adding
a wood strip (at least 1 1/2 wide)
along entire width of sill. Fasten
wood strip to sill with at least three
countersunk wood screws (not
supplied with kit). This provides a
smooth surface for mounting air
conditioner.
4
INSTALL UNIT
IN WINDOW
Place unit in window. Lower sash
until it rests behind front flange of top
rail. Bottom rail must rest behind
window sill. With a level adjust unit
to a 1/2 bubble slope to the rear for
proper water drainage.
INSTALL
BASEPAN ANGLE
Back front attachment screw out
several turns and slip Basepan Angle
over screw head. Snug screw with
angle resting on window ledge.
Install two 25-mm screws through
angle into window ledge. Repeat for
opposite side.
5
8
SILL
Wood
Strip
1/2"
Minimum
O
U
T
D
O
O
R
Storm Window
Frame
1 1/2"
Minimum
I
N
D
O
O
R
1 1/2"
Minimum
Wood
Strip
I
N
D
O
O
R
O
U
T
D
O
O
R
Window
Frame
Must be a minimum
of 1/2" to clear
bottom rail on unit
Curtain assembly cut
away for clarity.
Window sash
Level
25-mm
screws
Basepan
angle
Front attachment
screw
A
B
La prise de courant doit
se trouver à moins de
5 pieds (1,53 m) de ce point
Bois de
charpente
A
B
Bois de
charpente
AAC051SRA
AAC081SRA 14 1/2 21 7 1/2
AAC101SRA 17 22 1/2 10 5/8
AAC121SRA 17 22 1/2 10 5/8
AAC141SRA 18 1/8 26 1/2 10 5/8
AAC182SRA 19 1/8 28 1/8 11 5/16
AAC202SRA 19 1/8 28 1/8 11 5/16
A B C
Modèle Dimension
53
ATTENTION
Linstallation dun climatiseur à travers un mur requiert
une vaste expérience en maçonnerie et/ou en
menuiserie. Les installations à travers le mur réalisées
par des personnes non qualifiées ou inexpérimentées
peuvent causer des dommages à la résidence.
Consignes dinstallation à
travers le mur
Calfater tous
les côtés
Linteau et
clignotement
(si nécessaire)
Le boîtier extérieur doit être
projeté d'un minimum de ¾ po
(1,9 cm) au-delà du mur intérieur
ou de la moulure pour fixer
le cadre avant.
c
Avant du boîtier
extérieur jusqu'aux
persiennes dé
gageant l'air
sur le côté
Poser le
boîtier avec
une pente
de 1/2
bulle vers l’arrière
pour assurer
l’écoulement
adéquat de l’eau.