STREAK 800Pro HEXACOPTER Instruction Manual 1
Contents 1. Safety Notes........................................................................................................................................................3 2. Equipment Required For Assembly....................................................................................................................4 3. Check List............................................................................................................................................................5 4.
1. Safety Notes Do fly only in safe areas and always away from other people! Do not operate RC aircraft within the vicinity of homes or crowds of people. RC machine are prone to accidents, failures, and crashes due to a variety of reasons including pilot error, radio interference, and lack of maintenance. Pilot are responsible for their actions and damage or injury occuring during the operation of RC aircraft machine.
2. Equipment Required For Assembly 6pcs-- 40A ESC(6S 18pcs-- 3.5mm Bullet 1pcs-- “+” Mode 22.2V) (e.g. HobbyWing Connector (Female) for Hexacopter Controller FlyFun 40A ESC) 6pcs ESC (e.g. DJI WK-M) 2pcs-- 6S LiPo Battery 3500-7500mAh 22.2V ( Will be connected in Parallel) 2pair-- Connectors For Batteries and Power Board 1pcs-- Lipo Charger & the connector to fit the Lipo Battery.
3. Check List Please Check the Follow parts. Alware Multicopter Brushless Motor 3515-15 KV400 (Not included unless otherwise specified.) 6 Set Screw set come with Motor. Apc Propeller 14x4.7SFP (CW) 3 Pcs Apc Propeller 14x4.7SFP (CCW) 3 Pcs Large Current Power/ESC Board (Black/ Blue color) with 2 pairs Battery Cable.
AWG wire Black ( 33cm ) 6 pcs AWG wire Red ( 33cm ) 6 pcs Frame parts.
Other parts : Spare Hex Cap Screw M2x6mm Spare Hex Cap Screw M3x8mm Spare Hex Cap Screw M3x10mm Spare Hex Cap Screw M3x12mm Spare Round Cap Screw 1pcs x Direction Indicating Sticker 7 8pcs x Battery Support Damper
4.1 Assembly Steps - Flight direction indicator Step 1. Cut the Direction Indicating Sticker with a width of around 100mm. Step 2. Tear the cover layer of the Sticker before stick to the front Carbon Arm Boom. Step 3. Stick the Direction Indicating Sticker to the Fixed Carbon Arm Boom as to indicate the Forward Flying Direction. Step 4. Use three pieces of Adhesive Tape to secure the Direction Indicating Sticker. Step 5. Prepare the FPV & GPS Mounting Assembly. Step 6.
4.2 Assembly Steps – Motor Step 1. You will received 6 motors in ALS800-CB. Step 2. For new motors, Thread Lock must be applied to the two M3 Set Screws which is pre-inserted in the motor. (This is a must for safety flying.) Step 3. Install the Porp Mount to the motor using 3pcs M3 Hex Cap Screw. (Apply little amount of Thread Locker when assembly metal to metal parts.) Step 4. Double check the prop mount which must be installed to the motor securely.
4.3 Assembly Steps – Motor Mount Step 1. Loosen the two screws before insert the motor mount to the Carbon Arm Boom. Step 2. Insert the Motor Mount to the carbon boom and stop until the boom edge is around 5mm to the Inner Motor Metal Mount surface. Step 3. Adjust the Motor Mount to parallel to the Streak 800Pro body before tighten the screws. Step 4. Secure the Motor Mount by tighten the screws on the Metal Mount. Repeat Step 1 to 4 to install other Motor Mounts to the Carbon Boom Arms.
4.4 Soldering Job Solder 2 pairs Battery Cable to the Large Current Power/ESC Board and connect the other end to the Battery Connectors. (Red = +ve , Black = -ve) Do not short circuit two polarities!! 1.) Solder Black and Red AWG wires to the ESC. 2.)Solder 3pcs 3.5mm Bullet Connectors (Female) to the ESC. 3.)Connect Servo Extension Wire to the Signal Connector of ESC and secure it using Adhesive Tape.
4.5 Assembly Steps – ESC and ESC board. Step 1. Uninstall the Upper Main Frame of Streak 800Pro by loosing 18pcs M3 Screws as shown above. Step 2. Insert the Battery Power Cable and Signal Wire of the ESC into the Carbon Boom Arm. Same for all 6pcs ESCs. Step 3. Solder the Battery Power Wires of the ESC to the ESC Board. (Red wire = +ve , Black wire = -ve) Step 4. Solder 2 pairs Battery Cable to the Large Current Power/ESC Board and connect the other end to the Battery Connectors.
Step 5. Install the Upper Main Frame back to the body. (Apply little amount of Thread Locker when installing Screws to metal part.) Step 6. Insert the FPV & GPS Mounting Assembly completely to touch the Upper Main Frame and secure it by tighten the M3 Screw circled above. Step 7. Prepare the Landing Gear Frame Assembly. Step 8. Install the Landing Gear Frame Assembly to the Lower Main Frame of the body using four M3x10 Hex Cap Screws.
4.6 Assembly Steps – Motors & Propellers. Step 1. Prepare 4pcs M3x8mm HexCap Screws with 4pcs 3mm Washers to install the motors to the Motor Mounts. Step 2. Insert a M3x8mm Screw into a 3mm Washer then insert to the motor mount slot as to mount the Motor to it. (Apply little amount of Thread Locker when assembly metal to metal parts.) Step 3. Secure the motor to the motor mount with 4pcs screws and washers. Step 4. Insert the Motor Wires into the slot of motor mount and connect with motors.
Step 5. Repeat Step 1 to 4 for other 5 motors. Test the motor first without propellers as to ensure the rotating direction is correct. Exchange any two motor wires to the ESC as to reverse the direction if needed. Step 6. After ensuring the motors are running in the correct direction, prepare the APC Props and Prop mounting screw and washer from the motors. Step 7. Insert the Root Hole Adapter (with 6mm inner diameter) to the bottom side of APC Prop. Step 8.
4.7 Assembly Steps – Bipod Landing Gear. Step 1. Insert the Landing Gear Skid into the mounting hole of Carbon Fiber Leading Gear Assembly. (Tips: You can rotate the Landing Gear Skid into the hole with less effort.) Step 2. Adjust the length of the Landing Gear Skid. Each side of the Landing Gear Skid should be about 195mm. Step 3. Secure Landing Gear Skid onto the Carbon Fiber Leading Gear Assembly using the M3 Set Screw which is pre-installed on the Landing Gear Skid Metal Mount. Step 4.
Step 5. Correct two Bipod Landing Gear Assemblies. Step 6. Insert the Carbon Boom of Bipod Landing Gear Assembly into the metal mount of Landing Gear Frame Assembly with the depth of approximately 5mm. Step 7. Adjust the Bipod Landing Gear Assembly to make the Landing Gear Skid be parallel to the Fixed Arm and secure the Landing Gear Frame Assembly with the M3 Screw.
5. Quick Collapsible Illustration With the Quick Collapsible Design, you can fold four arms of Streak 800 easily for easy transportation and storage. However you must follow the coming step by step to fold the arms correctly, otherwise the Lock System may damaged! Step 1. Four Arms of Streak 800Pro are locked with four Thumb Screws with Split Lock Washers. Step 2. Loosen the Thumb Screw and make sure it is not touching the Fiber Frames. Then the Arm can be folded or opened. Step 3.
Step 4. Always check the above Screws are not loosen, but not tighten completely too, otherwise the Arms will not be foldable. If you found that it is getting loosen, secure it with Thread Locker for secure flight. Adjust the tightness of these screws for the smoothness of folding the arms, loosen it a little bit if your folding arms are too tight. ***Always check if the above four Screws are secured tightened completely for secure flight.
6. Gimbal Mounting Step 1. Indicate the Multi-Gimbal Mount which is installed with Landing Gear Frame Assembly. Step 2. Mounting position for GAUI CRANE 3 and CRANE 2 Gimbals. Step 3. Mounting positions for other Gimbals such as STO S-903(3-axis) Gimbal, STO Camera Mount Kit S-550 etc.
Mounting with Lensman-18A 3-Axis Gimbal: Step 1. Prepare the Lensman-18 Gimbal Mounting Frame Model: ALLENS-18GMF (optional item, not included) if you want to install with Lensman-18A Gimbal. Step 2. Install the Lensman-18 Gimbal Mounting Frame onto the Lensman-18A Gimbal. Step 3. Replaced the installed Landing Gear Frame Assembly(Step 8) from the Lower Main Frame of the body with the Lensman-18A Gimbal with the Mounting Frame installed (Step 2) using four M3x 14mm Hex Cap Screws with 3x5x3mm Collars.
7. Multicopter Controller Mounting Illustration. Overall electronics mounting for reference. Installation of WK-M, Front View. Back View. GPS Compass mounting for reference.
8. Specification Kit: -Diagonal Wheelbase: 800mm -Carbon Arm Boom Length: 281mm -Carbon Arm Boom Weight: 23.
Speed Controller/ ESC: -Current: 40A or Above -Voltage: 22.2V 6S LiPo -Largest Dimension: 30x80x25mm (WxLxH) -Recommended ESC: HobbyWing 40A ESC(for 22.2V 6S Lipo) Flying Parameters: -Max. Takeoff Weight: 7.0Kg -Max. PayLoad Weight: 2.3Kg (With 12600mAh Lipo-1.7Kg) -Power Battery: 9000-15000mAh 22.2V 6S LiPo (Minimum 15C) -Hover Power Consumption: 1300W (Takeoff Weight 6.5Kg) -Max. Hover Time: 15 min (With 12600 mAh & 6.
