Instruction manual
Appendix C
C-17
BreezeACCESS Version 4.3 System Manual
*ScrambledSeqTableIdx
710.3.3. 6.15. 9.5.1.1
(**ScrambledSeqEntry 1)
Applicable to SU and AU only. Read-
only. A Scrambled Sequence Table
entry index.
Integer
*ScrambledSeqFreqIdx
710.3.3. 6.15. 9.5.1.2
(**ScrambledSeqEntry 2)
Applicable to SU and AU only. Read-
only. A Frequency Index in the
Scrambled Sequence Table.
DisplayString (SIZE(10))
*CallAgingTime
710.3.3. 6.16
(*AirInterface 16)
Applicable to AU only. The aging
time for a voice call in the Call Info
database.
Integer
1-50,000 (seconds)
1=No aging
*SecurityParameters
710.3.3. 6.17
(*AirInterface 17)
Security Parameters
*PrivacyOptionImplemented
710.3.3. 6.17.1
(*SecurityParameters 1)
Applicable to SU and AU. Read
Only. Enable/disable the privacy
option. Normally set to active.
Integer
notActive (0)
active (1)
*AuthenticationAlgorithm
710.3.3. 6.17.2
(*SecurityParameters 2)
Applicable to SU and AU only.
Enables/disables the authentication
option.
openSystem: authentication
messages are not encrypted.
sharedKey: Authentication
messages are encrypted.
supportAll: Applicable for AU only.
Allows authentication of all SUs,
regardless of the Authentication
Algorithm and WEP Key used in the
SU.
Integer
openSystem (0)
sharedKey (1)
supportAll (2) (AU only)
*DefaultKeyID
710.3.3. 6.17.3
(*SecurityParameters 3)
Applicable to SU only. The ID of the
key to be used for encryption the
authentication messages.
Integer
1-4
*WEPKey1
710.3.3. 6.17.4
(*SecurityParameters 4)
Applicable to SU and AU only.
Encryption WEP Key#1. Accessible
only with SNMP Write Community.
DisplayString (SIZE(10))
Ten hexadecimal digits
*WEPKey2
710.3.3. 6.17.5
(*SecurityParameters 5)
Applicable to SU and AU only.
Encryption WEP Key#2. Accessible
only with SNMP Write Community.
DisplayString (SIZE(10))
Ten hexadecimal digits
*WEPKey3
710.3.3. 6.17.6
(*SecurityParameters 6)
Applicable to SU and AU only.
Encryption WEP Key#3. Accessible
only with SNMP Write Community.
DisplayString (SIZE(10))
Ten hexadecimal digits
*WEPKey4
710.3.3. 6.17.7
(*SecurityParameters 7)
Applicable to SU and AU only.
Encryption WEP Key#4. Accessible
only with SNMP Write Community.
DisplayString (SIZE(10))
Ten hexadecimal digits.
*CurrentTxPwrLvl
710.3.3. 6.18
(*AirInterface 18)
Applicable only to SU-R units and to
SU-I and AU-I units with HW version
C or lower.
Enables setting the transmitted
power level according to the unit
capabilities.
In SU-R-3.5ab, If ATPC is enabled
the algorithm uses it as the initial
power level
.
Integer
Low (0)
high (1)medium (2)
– applicable only to
SU-R-3.5ab
*WirelessTrapThreshold
710.3.3. 6.19
(*AirInterface 19)
A wireless link quality threshold for
sending the *WirelessStatusTRAP,or
*WirelessStatusOfSUsTRAP.
These traps indicate whether the
quality has gone below or above the
specified threshold.
Integer
SU: 0-255 (RSSI units)
AU: 0-100 (% retransmissions)
*NumberOfHoppingFrequenciess
710.3.3. 6.20
(*AirInterface 20)
Applicable to SU and AU. Read-only.
The Number of Hopping
Frequencies used in the AU.
Integer
0-151
na (255)
MIB Parameter
(Location in Parenthesis)
Description Values/Range