BreezeACCESS V Version 4.3 Revision 4.0A June 2003 System Manual Cat. No. Revision 4.
© 2003 by Alvarion Ltd. All rights reserved. No part of this publication may be reproduced in any material form without the written permission of the copyright owner. Trade Names Alvarion®, BreezeACCESS®, BreezeCOM®, BreezeLINK®, BreezePHONE®, BreezeNET®, WALKair®, WALKnet®, are trade names or trademarks of Alvarion Ltd. Other brand and product names are trade names or trademarks of their respective owners.
BreezeACCESS Version 4.3 System Manual ii (c) ALVARION SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY PURCHASER’S OR ANY THIRD PERSON'S MISUSE, NEGLIGENCE, IMPROPER INSTALLATION OR IMPROPER TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD. Limitation Of Liability.
Important Notice iii BS-GU Lithium Battery Caution: Danger of battery explosion if incorrectly replaced or disposed of. Replace only with the same or equivilant type battery, as recommended by the manufactuer. Dispose of used batterys according to manufactuer’s instructions. Line Voltage Before connecting this instrument to the power line, make sure that the voltage of the power source matches the requirements of the instrument. Power Cord Use only the power cord supplied with the unit.
BreezeACCESS Version 4.3 System Manual iv Important Notice This user manual is delivered subject to the following conditions and restrictions: This manual contains proprietary information belonging to Alvarion Ltd. Such information is supplied solely for the purpose of assisting properly authorized users of the respective Alvarion Ltd. products.
Important Notice v . NOTE: The currently released BreezeACCESS V product line does not include certain products and features which are described in this manual.
vi BreezeACCESS Version 4.
Table of Contents i Table of Contents System Manual Book 1: System Description Introduction ............................................................. 1-1 Introducing BreezeACCESS ..................................................... 1-2 System Components ................................................ 2-1 Subscriber Units (Customer Premises Equipment) ............... 2-2 SU-A/E Units with an Outdoor Radio Unit and Antenna .... 2-2 Base Station Equipment ..............................................
BreezeACCESS 4.3 System Manual ii System Manual Book 2: Installation IF-Based Equipment ................................................ 1-1 Modular Base Station Equipment ...................................... 1-2 Standalone AU-E-NI Access Unit ...................................... 1-3 Other Items Required for Installation ................................. 1-3 Guidelines for Selection of Equipment Locations ................. 1-5 AU-RE .....................................................................
Table of Contents System Manual Book 3: Commissioning Setting Basic Parameters ....................................... 1-1 Accessing the Monitor Program .............................................. 1-2 Accessing the Monitor Program using the RS 232 MON Connector ............................................. 1-2 Accessing the Monitor Program using Telnet .................... 1-3 Operating the Monitor Program .........................................
BreezeACCESS 4.3 System Manual iv System Manual Book 4: Operations and Administration Accessing the Monitor Program .............................. 1-1 Accessing the Monitor Program using the RS 232 MON Connector ...................................................... 1-2 Accessing the Monitor Program using Telnet ........................ 1-3 Operating the Monitor Program ............................................... 1-4 Menus and Parameters ............................................ 2-1 Main Menu ....
Table of Contents Telephony Signals (Subscriber Units with Voice Support Only) ................... 2-104 Hopping Parameters (GU) ............................................. 2-110 Alarm Parameters (GU) ................................................. 2-112 System Manual:Appendices Appendix A: Configuration Download/Upload .........A-1 Appendix B: Software Version Loading Procedure B-1 General ......................................................................................
vi BreezeACCESS 4.3 System Manual Appendix D: RSSI to dBm Conversion Table ...........D-1 Appendix E: Parameters List ................................... E-1 Unit Control Parameters ...........................................................E-1 Site Survey Parameters ............................................................E-2 IP Parameters ............................................................................E-3 Air Interface Parameters ...........................................................
BreezeACCESS V Version 4.3 Revision 4.
System Description Table of Contents Introduction .............................................................1-1 Introducing BreezeACCESS .....................................................1-2 System Components ................................................2-1 Subscriber Units (Customer Premises Equipment) ...............2-2 SU-A/E Units with an Outdoor Radio Unit and Antenna .....2-2 Base Station Equipment ...........................................................
ii BreezeACCESS Version 4.
Chapter 1 Introduction About This Chapter This chapter introduces the BreezeACCESS system, its components and its functions.
BreezeACCESS Version 4.3 System Description 1-2 Introducing BreezeACCESS BreezeACCESS IP Broadband Wireless Access system is an IP based access system that supports wireless data and voice services, employing wireless packet-switched data technology to support high-speed IP services, including fast access to the Internet and Virtual Private Networks.
Introduction 1-3 INT (International) Option – The available band ranges from 5.725 GHz to 5.850 GHz. Two hopping sequence selection modes are supported as follows: a. INT ISM mode: This option supports the standard ISM US FCC Frequency Hopping sequence that includes 79 frequencies. Synchronization among AUs is supported. b. Flexible Hopping Mode: Enables the selection of hopping frequencies in the supported range. Synchronization among AUs is supported.
1-4 Manual Revision: 4.0 BreezeACCESS Version 4.
Chapter 2 System Components About This Chapter This chapter describes BreezeACCESS system components. It includes the following sections: Subscriber Units (Customer Premises Equipment)‚ page 2-2, describes BreezeACCESS equipment installed at the customer’s premises. Base Station Equipment‚ page 2-4, describes the equipment used in BreezeACCESS Base Stations.
BreezeACCESS Version 4.3 System Description 2-2 Subscriber Units (Customer Premises Equipment) The BreezeACCESS Subscriber Unit (SU) installed at the customer premises provides data only or data and telephone connections. The data connection is a standard IEEE 802.3 Ethernet 10BaseT (RJ 45) interface while the voice connection (in units that support voice) is a standard RJ 11 Plain Old Telephone (POTS) interface.
System Components 2-3 Figure 2-1: BreezeACCESS SU-A/E Outdoor and Indoor Units NOTE: Units operating in the 5.7 GHz band are supplied either with a rectangle shaped antenna (left of figure), or with a diamond shaped antenna (right of figure). The following products are available: Data-only Units: SU-X-1D- FF The unit supports one Ethernet device. SU-X-BD- FF The unit provides bridge functionality and can support up to a full LAN.
BreezeACCESS Version 4.3 System Description 2-4 X=A: The outdoor radio unit includes an integral high gain flat antenna X=E: The outdoor radio unit has a connector for an external antenna. FF: The radio band supported by the unit (5.2 or 5.7 GHz). Base Station Equipment The BreezeACCESS Access Units (AU) installed at the base station site provide all the functionality necessary to communicate with the remote Subscriber Units as well as to connect to the backbone of the service provider.
System Components 2-5 Figure 2-2: BreezeACCESS Base Station Module and Outdoor Unit GU-A-BS GPS and Alarms System The optional GU-A-BS system can be used to synchronize the frequency hopping mechanisms of collocated AU-E-BS BreezeACCESS units (where such synchronization is permitted by local regulations) as well as to provide alarm management. The GU-A-BS system is comprised of two units: An outdoor GPS Receiver and Antenna unit, the GU-RA. An indoor GPS and Alarms module, the BS-GU.
BreezeACCESS Version 4.3 System Description 2-6 Figure 2-3: BreezeACCESS GU-A-BS System Components The BreezeACCESS BS-GU module is designed to be inserted into the BS-SH 19” base station chassis to provide hopping synchronization signals to the BS-AU Access Unit modules. The card uses timing signals derived from signals received from the GU-RA GPS antenna. These signals, generated by the GPS global satellites network, allow accurate synchronization of systems located in different locations.
System Components 2-7 Daisy-chained BS-GU modules use the synchronization signals generated by the first module in the chain (the Master module. The BS-GU module also supports the management of alarm inputs and outputs. The module receives Alarms In indications from other BreezeACCESS modules in the base station shelf (internal alarms) and external alarms from other devices via the AL IN connector.
BreezeACCESS Version 4.3 System Description 2-8 Networking Equipment The base station equipment is connected to the backbone through standard data communication and telecommunication equipment. For improved security, the 10BaseT ports of the AU modules are connected directly to a multi-port router. This router is connected by any means of point-to-point link to the backbone.
System Components 2-9 BreezeMANAGE Alvarion’s SNMP-based BreezeMANAGE network management application provides a powerful tool for configuring, controlling, monitoring and effectively managing BreezeACCESS networks from a single, central network management station. BreezeMANAGE, together with the powerful tools available through its use under leading network management platforms, provides numerous benefits to operators of BreezeACCESS networks.
BreezeACCESS Version 4.3 System Description 2-10 BreezeCONFIG The BreezeCONFIG ACCESS configuration utility can also be used to manage BreezeACCESS system components. It is an SNMP-based application that provides a consistent view of the network and the system administrator can use it to control a large number of units from a single location.
Chapter 3 Specifications About This Chapter This chapter lists the technical specifications of BreezeACCESS and includes the following sections: System Specifications‚ page 3-2, outlines the technical specifications of the BreezeACCESS system. Physical Specifications‚ page 3-7, lists the physical and electical specifications for different types of BreezeACCESS units.
BreezeACCESS Version 4.3 System Description 3-2 System Specifications Radio and Modem 5.2 GHz Band Parameter Value Operation Mode Time Division Duplex Radio Access Method FH-CDMA Antenna Port N-Type connector, 50 ohm The tested external sector antenna for the AU: 16 dBi, 5.150-5.
Specifications 3-3 Radio and Modem 5.7 GHz Band Parameter Value Frequency 5.725-5.850 GHz Standard Compliance FCC Part 15.247, ETS 301 253 Channel Bandwidth 1 MHz Central Frequency Resolution 1 MHz SU-RA Antenna 21dBi, 10o horizontal x 10 o vertical, vertical polarization, EN 302 085 Class TS 3 range 1 compliant Output Power (at antenna port) 26 dBm typical.
BreezeACCESS Version 4.3 System Description 3-4 Telephony (Subscriber Units with voice support) Parameter Value Call Progress Tones Selectable per country standard or user definable Line Type Loop Start On-hook Voltage -48 V Ringer Voltage Min. 50 V r.m.s. unbalanced Ringer Frequency Selectable: 17, 20, 25, 50 Hz REN Max. 2 Off-hook DC current 30mA Off-hook impedance 600 ohm or complex Maximum input level +3 dBm Cable length Max.
Specifications 3-5 Parameter Value Security a. Association protocol – ESSID b. RC4 WEP option (encryption of the authentication process) c. VLAN according to IEEE 802.1Q d. IP level filtering for user addresses or protocols e.
BreezeACCESS Version 4.3 System Description 3-6 Standards Compliance, General Type Standard EMC FCC part 15 (5.7 series), EN 300 385 Safety UL 1950, EN 60950 Environmental ETS 300 019 part 2-3 class 3.2E for indoor units ETS 300 019 part 2-4 class 4.1E for outdoor units Radio FCC part 15.247, ETSI ETS 301 253 Manual Revision: 4.
Specifications 3-7 Physical Specifications SU-A/E Subscriber Unit Connectors Unit Connector SU-NI SU-RE SU-RA Description IF TNC jack, 50 ohm, lightning protected ETH 10BaseT Ethernet (RJ 45) with 2 embedded LEDs.
BreezeACCESS Version 4.3 System Description 3-8 Unit Structure SU-RA 5.2 GHz Dimensions Weight Metal box plus an integral antenna in a cut diamond 43.2 x 30.2 x 5.9 shape in plastic enclosure, pole or wall mountable cm (30.6 x 12 x 4.7 cm + 43.2 x 30.2 x 1.
Specifications 3-9 Modular Base Station Equipment Connectors Unit AU-E-BS Connector AU-BS Description IF TNC jack, 50 ohm, lightning protected ETH 10BaseT Ethernet (RJ 45) with 2 embedded LEDs Cable connection to a PC: crossed MON RS 232, 3-pin low profile jack IF TNC jack, 50 ohm, lightning protected ANT N-Type jack, 50 ohm, lightning protected BS-PS -48V 3 pin DC power plug BS-PS-AC AC IN 3 pin AC power plug BS-GU ETH 10BaseT Ethernet (RJ 45) with 2 embedded LEDs Cable connection to
BreezeACCESS Version 4.3 System Description 3-10 Modular Base Station Equipment - Electrical Unit Details General 200 W for a fully equipped chassis (1 PS, 6 AU, 1 GU) BS-PS DC power input: -48 V, 5.2 A max. DC power output: 12 V; 5 V BS-PS-AC AC power input: 85-256 VAC, 47-65 Hz, DC power output: 12 V; 5 V; 3.
BreezeACCESS V Version 4.3 Revision 4.
Installation Table of Contents IF-Based Equipment .................................................1-1 Modular Base Station Equipment .......................................1-2 Standalone AU-E-NI Access Unit .......................................1-3 Other Items Required for Installation ..................................1-3 Guidelines for Selection of Equipment Locations ..................1-5 AU-RE ................................................................................1-5 SU-RA and SU-RE .........
ii BreezeACCESS Version 4.3 Installation Antenna Seal ..................................................................... 2-4 Lightning Protection ........................................................... 2-4 Installing SU-R Indoor Units ..................................................... 2-5 Wall Mounting the Unit ....................................................... 2-5 Connecting the Omni Antennas ......................................... 2-6 Connecting a Detached Antenna ......................
Chapter 1 IF-Based Equipment About This Chapter This chapter describes the basic installation of BreezeACCESS IF-based equipment, including SU-A/E subscriber units, modular base station equipment and stand-alone AU-E-NI access units. It includes the following sections: Packing Lists‚ page 1-2, lists the equipment that is packed with each BreezeACCESS IF-based unit. Guidelines for Selection of Equipment Locations‚ page 1-5, gives tips and guidence for locating BreezeACCESS equipment for optimum performance.
BreezeACCESS Version 4.3 Installation 1-2 Packing Lists NOTE: According to the FCC all IF Units (AU-E, SU-A, SU-E) should be installed by a professional installer only.
IF Based Equipment 1-3 BS-PS DC Power Supply (one or two per chassis) BS-PS power supply module DC power cable BS-PS-AC Power Supply (one or two per chassis) BS-PS-AC power supply module AC power cable GU-A-BS GPS and Alarms System BS-GU module GU-RA GPS antenna and receiver 1” threaded mounting pole for the GU-RA GPS antenna Antenna Mounting kit Standalone AU-E-NI Access Unit AU-RE with a connector to an external antenna (not included) Pole mounting kit for the outdoor unit AU-NI indoor unit Wall moun
BreezeACCESS Version 4.3 Installation 1-4 Alarms-In and Alarms-Out cables* for the GPS module (if necessary) Installation tools and materials For local configuration of parameters: A portable PC with Terminal Emulation software and Monitor cable* (Monitor cable is supplied with Access Units) –Or– A portable PC equipped with an Ethernet card and with Telnet software, and an Ethernet cable (see Table 1-1‚ page 1-4) Items marked with an asterisk (*) are available as options from Alvarion.
IF Based Equipment 1-5 Guidelines for Selection of Equipment Locations NOTE: Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the BreezeACCESS product warranty and may expose the end user or the service provider to legal and financial liabilities.
BreezeACCESS Version 4.3 Installation 1-6 IF Cable The outdoor unit is connected to the indoor unit by means of an IF cable carrying signaling, control signals and power. The IF frequency is 440 MHz. The maximum allowed attenuation of the IF cable connecting the outdoor unit to the indoor unit is 15 dB at 440 MHz, and the maximum allowed DC resistance (the sum of the DC resistance of the inner and outer conductors) is 1.5 ohm. This allows for cable length of up to 30 m when using the standard RG 58 cable.
IF Based Equipment 1-7 Installing the Outdoor Unit NOTE: Outdoor units must be installed by a professional installer only. The Outdoor Unit Bottom Panel The SU-RA outdoor unit includes the radio and an integral high-gain flat antenna located on the front of the unit. The SU-RE and AU-RE outdoor radio units have an RF connector for connection to an external antenna.
BreezeACCESS Version 4.
IF Based Equipment 1-9 Pole Mounting the Outdoor Unit The outdoor unit can be secured to the pole using one of the following options: Special brackets and open-ended bolts (supplied with each unit). There are two pairs of threaded holes on the back of the unit, allowing use of the special brackets with various pole widths. Metal bands (9/16" wide, minimum 12" long). Figure 1-3‚ page 1-10 shows the locations of the band grooves and threaded holes on the rear side of the outdoor unit.
BreezeACCESS Version 4.3 Installation 1-10 Figure 1-3: Grooves/Threaded Holes Figure 1-4: 3" Pole Mounting Installation Using the Special Brackets NOTE: When inserting the open-ended bolts, make sure to insert them with the grooves pointing outwards; these grooves are intended to allow fastening of the bolts with a screwdriver. Manual Revision: 4.
IF Based Equipment 1-11 Connecting the Antenna Cable (SU-RE and AU-RE) Connect an RF cable between the ANT connector (located on the top panel of the unit) and the antenna. Connecting the Ground and IF Cables The ground terminal (marked ) and the IF cable connector (marked IF) are located on the bottom panel of the unit. 1. Connect one end of the ground cable to the ground terminal and tighten the ground screw firmly. Connect the other end of the ground cable to a protective ground connection. 2.
BreezeACCESS Version 4.3 Installation 1-12 Installing the SU-NI and AU-NI Indoor Unit Figure 1-5: SU-NI with Voice Support Rear Panel Figure 1-6: SU-NI/AU-NI Front Panel NOTE: The rear panel pictured above in Figure 1-5 is a SU-NI with voice support; AU-NI units and SU-NI units that belong to Subscriber Units without voice support are identical, except that they have no TEL port.
IF Based Equipment 1-13 The SU-NI/AU-NI provides the following interfaces: An Ethernet connector (marked ETH) for connecting the unit to the network. See Table 1-1‚ page 1-4 for information on the required type of Ethernet cable. An IF connector for connecting the unit to an outdoor unit. A DC-12V connector for the power supply. A MON connector for connecting an ASCII terminal with terminal emulation software for configuration and maintenance purposes.
BreezeACCESS Version 4.3 Installation 1-14 Installing Modular Base Station Equipment BS-SH Slot Assignments The base station chassis has ten slots. Figure 1-7: BS-SH Chassis Slot Assignments The two wide slots on both sides of the shelf accommodate the BS-PS or BS-PS-AC power supply modules. The shelf is designed to support power supply redundancy through the use of two power supply modules. If a single power supply is used, it can be inserted in any of the two available slots.
IF Based Equipment 1-15 The BS-PS The BS-PS provides power to all the modules installed in the BS-SH chassis. The BS-PS front panel is shown in Figure 1-8‚ page 1-15. Figure 1-8: BS-PS Front Panel The BS-PS provides a power input connector (marked -48V) for connecting the -48VDC power source to the module. The color codes of the cable wires are: Black Red -48 VDC + (Return) The power switch turns the mains power to the power supply ON and OFF.
BreezeACCESS Version 4.3 Installation 1-16 The BS-PS-AC The BS-PS-AC is an AC to DC converter that provides power to all the modules installed in the BS-SH chassis. The BS-PS-AC front panel is shown in Figure 1-9‚ page 1-16. Figure 1-9: BS-PS-AC Front Panel The BS-PS-AC provides a power input connector (marked AC IN) for connecting the AC power cable to the mains. The ON/OFF power switch controls the connection of the mains power to an AC to DC converter. Table 1-8: BS-PS-AC LEDs LED Description 3.
IF Based Equipment 1-17 WARNING: If two power supply modules are used in the same chassis for redundancy, both power supplies must be of the same type. Do not use a mix of AC and DC power supply modules in the same chassis. The BS-AU Figure 1-10: BS-AU Front Panel Table 1-9: BS-AU LEDs Name Description Functionality PWR Power supply 12 VDC On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
BreezeACCESS Version 4.3 Installation 1-18 The BS-AU provides the following interfaces: An Ethernet connector (marked ETH) for connecting the BS-AU to the network. A straight Ethernet cable should be used to connect the module to a hub, router or switch. An IF connector for connecting the BS-AU to an outdoor unit (AU-RE). A MON connector for connecting an ASCII terminal with terminal emulation software for configuration and maintenance purposes.
IF Based Equipment 1-19 power source and the black wire to the -48 VDC contact of the power source. Connect the red wire to the + (Return) contact. Connect the shield to the ground. 6. If a BS-PS-AC AC power supply is used, connect the AC power cable to the AC jack (marked AC IN) located on the front panel of the BS-PS-AC power supply. If a redundant power supply module is installed, connect a power cable to that unit as well. Connect the power cable(s) to the AC mains. 7.
BreezeACCESS Version 4.3 Installation 1-20 Installing the GU-A-BS GPS and Alarms System BS-GU Front Panel Figure 1-11: BS-GU Front Panel Manual Revision: 4.
IF Based Equipment 1-21 Table 1-10: BS-GU Connectors Connector Name Functionality SYNC IN Receives signals from the GPS antenna unit. If more than one collocated BS-GU module is daisy-chained, this connector is used by a “Slave” module to receive signals from the “Master” module’s SYNC OUT connector. SYNC OUT Transfers the signals received on the SYNC IN port.
BreezeACCESS Version 4.3 Installation 1-22 Installing the GU-RA GPS Antenna 1. Screw the GPS antenna firmly to the special 1” threaded pole. 2. Use the mounting kit supplied with the unit (or any other suitable means) to secure the GPS antenna pole to an existing pole (e.g. any pole used for mounting base station antennas or the outdoor units of the BreezeACCESS Access Units).
IF Based Equipment 1-23 4. Connect the 12-pin round connector to the GPS antenna. 5. Route the cable to the location intended for installation of the BS-GU module. NOTE: Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities.
1-24 Manual Revision: 4.0 BreezeACCESS Version 4.
BreezeACCESS V Version 4.3 Revision 4.
Commissioning Table of Contents Setting Basic Parameters .......................................1-1 Accessing the Monitor Program ..............................................1-2 Accessing the Monitor Program using the RS 232 MON Connector ..............................................1-2 Accessing the Monitor Program using Telnet .....................1-3 Operating the Monitor Program ..........................................1-4 Configuring Basic Parameters in Access and Subscriber Units .................
ii BreezeACCESS Version 4.3 Commissioning BS-AU LEDs ...................................................................... 4-6 BS-GU LEDs ......................................................................
Chapter 1 Setting Basic Parameters About This Chapter This chapter explains how to configure the basic parameters of the BreezeACCESS system and includes the following section: Accessing the Monitor Program‚ page 1-2, explains how to accessyour BreezeACCESS units for configuration. Configuring Basic Parameters in Access and Subscriber Units‚ page 1-5, outlines the basic configuration process for BreezeACCESS AU and SUs.
BreezeACCESS Version 4.3 Commissioning 1-2 Accessing the Monitor Program Accessing the Monitor Program using the RS 232 MON Connector 1. Use the monitor cable to connect the MON connector of the unit to the COM port of your ASCII ANSI terminal or PC. The COM port connector on the monitor cable is a 9-pin D-type plug. 2. Run a terminal emulation program (such as HyperTerminal™). 3.
Setting Basic Parameters 1-3 BreezeACCESS/AU-BS Official Release Version – 4.0.40 Release Date: Thu Dec 20 20:21:36 2001 Main Menu ===================== 1 – Info Screens 2 – Unit Control 3 – Basic Configuration 4 – Site Survey 5 – Advanced Configuration X – Exit >>> Figure 1-1: Main Menu – Administrator Access Rights (SU and AU) The appearance of the Main Menu varies in accordance with the set access level. For users with Read Only access rights, only the Info Screens option is displayed.
BreezeACCESS Version 4.3 Commissioning 1-4 Table 1-2: Required Type of Ethernet Cable Unit Type Connection to a PC Connection to a Hub Subscriber Units Straight Crossed Access Units Crossed Straight GPS module Straight Crossed 2. The Select Access Level menu appears. Select the access level according to your authorized access rights. You will be requested to enter your password. After entering the correct password press Enter. Default passwords are listed in Table 1-1‚ page 1-2. 3.
Setting Basic Parameters 1-5 Configuring Basic Parameters in Access and Subscriber Units The Basic Configuration menu in the Monitor program includes all the parameters necessary for the initial operation of BreezeACCESS Subscriber and Access Units. In many installations, most of these parameters should not be changed from their default values.
BreezeACCESS Version 4.
Setting Basic Parameters 1-7 Configuring Parameters in GU-A-BS Units Introduction This section describes all the parameters that are necessary for the initial installation and operation of GU-A-BS units. Once the unit is properly installed and operational, other parameters can be configured using the monitor program via Telnet or SNMP management. NOTE: The BS-GU does not have an external MON port, and therefore must be configured using Telnet.
1-8 Manual Revision: 4.0 BreezeACCESS Version 4.
Chapter 2 Optimizing the Wireless Link About This Chapter This chapter explains how to optimize the performance of the wireless link of BreezeACCESS Subscriber Units and includes the following sections: Configuring the Maximum Data Rate (Subscriber Units)‚ page 2-2, explains how to read the RSSI measurement and to configure the optimum value for the Maximum Data Rate parameter.
BreezeACCESS Version 4.3 Commissioning 2-2 Configuring the Maximum Data Rate (Subscriber Units) The BreezeACCESS units transmit at data rates of 3 Mbps, 2 Mbps and 1Mbps. If the quality of the link is not sufficient, it is recommended to decrease the value of the Maximum Data Rate. Note that the higher the data rate, the higher the error rate. Before reaching a decision on the optimum value for the Maximum Data rate for a specific SU, it is recommended to acquire the RSSI results from the AU.
Optimizing the Wireless Link 2-3 Aligning the Antenna of the SU-A/E Subscriber Unit NOTE: Antenna alignment using the RSSI bar display is possible only after the Access Unit you wish to associate with is operational and the basic parameters in the Subscriber Unit were properly configured. Otherwise, the unit will not be able to synchronize and associate with the Access Unit.
2-4 Manual Revision: 4.0 BreezeACCESS Version 4.
Chapter 3 BS-GU Connectors About This Chapter This chapter explains how to connect external devices to the AL IN and AL OUT connectors of the BS-GU module. It also includes a description of the cable connecting the BS-GU to the GPS antenna and of the SYNC IN/SYNC OUT connectors’ pin assignments.
BreezeACCESS Version 4.3 Commissioning 3-2 Connecting External Devices to the BS-GU AL IN and/or AL OUT Connectors Open-ended cables are available from the company for connecting to the module external alarm inputs through the AL IN connector and/or activating external devices through the AL OUT connector. See the tables that follow for descriptions of the connectors’ pins functionality. For details on defining and using the alarm inputs and output, refer to Book 4: Operation and Administration.
Connecting External Alarm Devices 3-3 Alarms Out Cable Table 3-2: Alarms Out Cable 9-pin Micro D-Type AL OUT Connector Description Color Code 1 Relay 1 Common Brown 2 Relay 1 Normally Closed White 3 Relay 2 Common Green 4 Relay 3 Common Red 5 Relay 3 Normally Closed Black 6 Relay 1 Normally Open Purple 7 Relay 2 Normally Closed Yellow 8 Relay 2 Normally Open Orange 9 Relay 3 Normally Open Blue NOTE: The other side of the cable is supplied open-ended.
BreezeACCESS Version 4.3 Commissioning 3-4 NOTE: *Descriptions are with respect to the BS-GU SYNC IN connector side. Figure 3-1 shows a 9-pin Micro D-Type Connector (cable side), and Figure 3-2 shows a 12-pin round connector. 9-pin Micro D-Type connector Figure 3-1: 9-pin Micro D-Type Connector (cable side) 1 9 5 12-pin round connector Figure 3-2: 12-pin Round Connector Manual Revision: 4.
Connecting External Alarm Devices 3-5 SYNC Cable Cable Type: EIA RS-422 3X2X25AWG +1X2X24 AWG FTP Shielded cable. Table 3-4: SYNC Cable 9-pin Micro D-Type SYNC OUT Connector Description Color Code 9-pin Micro D-Type SYNC-IN Connector 1 GPS TX+/SYNC D+ Black 1 2 GPS TX-/SYNC D- Brown 2 5 1PPS+/SYNC S+ Red 5 6 1PPS-/SYNC S- Orange 6 8 DC GPS Green 8 9 Slave Yellow 9 3,4,7 Not connected 3,4,7 NOTE: * Descriptions are with respect to the SYNC OUT connector side.
3-6 Manual Revision: 4.0 BreezeACCESS Version 4.
Chapter 4 Verifying Proper Operation About This Chapter This chapter explains how to confirm that the BreezeACCESS system is functioning properly and includes the following sections: Verifying Connectivity ‚ page 4-2 , explains how to ensure that your BreezeACCESS and the equipment connected to them are operating properly. LED Indicators ‚ page 4-4 , lists the LEDs found on BreezeACCESS units and their meanings.
BreezeACCESS Version 4.3 Commissioning 4-2 Verifying Connectivity Verifying the Ethernet Connection Once you have connected the unit to an Ethernet outlet, verify that the Ethernet Integrity indicator (the yellow LED embedded in the Ethernet connector) is on, indicating that the unit is connected to an Ethernet segment. The Ethernet Activity indicator (the green embedded LED) should blink whenever the unit receives or transmits traffic on the Ethernet port.
Verifying Proper Operation 4-3 Verifying Proper Operation of the GU-A-BS GPS Unit NOTE: It may take up to 10 minutes from the time the GU-RA GPS antenna is powered up until it is fully synchronized with the GPS satellite system. When the unit is operating properly, the PWR and OK green LEDS should be on, indicating that the BS-GU module is supplying power to the GU-RA GPS antenna and that the GPS antenna is functioning properly.
BreezeACCESS Version 4.
Verifying Proper Operation 4-5 SU-NI and AU-NI Indoor Units LEDs Table 4-3: SU-NI and AU-NI Indoor Units LEDs Name Description Functionality PWR Power supply On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
BreezeACCESS Version 4.3 Commissioning 4-6 BS-AU LEDs Table 4-6: BS-AU LEDs Name Description Functionality PWR Power supply 12 VDC On – After successful power up, indicating that 12 VDC is supplied to the outdoor unit.
BreezeACCESS V Version 4.3 Revision 4.
Operations and Administration Table of Contents Accessing the Monitor Program ..............................1-1 Accessing the Monitor Program using the RS 232 MON Connector ......................................................1-2 Accessing the Monitor Program using Telnet ........................1-3 Operating the Monitor Program ...............................................1-4 Menus and Parameters ............................................2-1 Main Menu .................................................
ii BreezeACCESS Version 4.3 Operations and Administration Service Parameters (AU and SU) .................................... 2-86 RADIUS Parameters Menu (Subscriber Units only) ....... 2-90 Security Parameters (AU and SU) ................................... 2-94 Voice Parameters (Subscriber Units/Voice Support Only) 2-96 Dialing Parameters (Subscriber Units/Voice Support Only) 2-97 Telephony Signals (Subscriber Units/Voice Support Only) 2-104 Hopping Parameters (GU) ......................................
Chapter 1 Accessing the Monitor Program About This Chapter This chapter explains how to access the monitor program. It also describes how to use the monitor program to set up, configure, and manage BreezeACCESS Broadband Wireless Access system units. This includes the Subscriber Units (SUs), Access Units (AUs) and GPS and Alarms modules (GUs).
BreezeACCESS Version 4.3 Operations and Administration 1-2 Accessing the Monitor Program using the RS 232 MON Connector 1. Use the monitor cable to connect the MON connector of the unit to the COM port of your ASCII ANSI terminal or PC. The COM port connector on the monitor cable is a 9-pin D-type plug. NOTE: The GU-BS GPS and Alarms module does not have an external MON port.
Accessing the Monitor Program 1-3 Accessing the Monitor Program using Telnet 1. Connect a PC to the Ethernet port of the unit. See the table below to determine the type of cable. Configure the PC’s IP parameters to enable connectivity with the unit (the default IP Address is 10.0.0.1). Run the Telnet application.
BreezeACCESS Version 4.3 Operations and Administration 1-4 For users with Installer access rights, the first four menu items (Info Screens, Unit Control, Basic Configuration and Site Survey) are displayed. Users with this access level cannot access the Advanced Configuration menu. For users with Administrator access rights, the full Main Menu will be displayed. These users can access all the menu items.
Chapter 2 Menus and Parameters About This Chapter This chapter describes the BreezeACCESS configuration menus and parameters. It includes the following sections: Main Menu‚ page 2-2. Info Screens Menu‚ page 2-3. Unit Control Menu‚ page 2-6. Basic Configuration Menu‚ page 2-13. Site Survey Menu‚ page 2-15. Advanced Configuration Menu‚ page 2-36.
BreezeACCESS Version 4.3 Operations and Administration 2-2 Main Menu From the Main Menu you can access the following menus, depending on your access level: Info Screens – Provides read-only display of current parameter values. Available at all access levels. Unit Control – Enables access to general operations such as resetting the unit, loading the default parameters, changing passwords and switching between software versions. Available at the Installer and Administrator access levels.
Menus and Parameters 2-3 Info Screens Menu BreezeACCESS/AU-BS Official Release Version – 4.0.40 Release Date: Thu Dec 20 21:05:08 2001 Info Screens ==================== 1 – Show Unit Status 2 – Show Basic Parameters 3 – Show Advanced Parameters S – Show All Parameters >>> Figure 2-1: Info Screens Menu The Info Screens menu enables viewing of the current values of various parameter sets. The parameter sets are identical to the main parameter groups in the configuration menus.
BreezeACCESS Version 4.3 Operations and Administration 2-4 Console Speed – Displays the speed defined in the unit for the connected terminal, used for running the terminal emulation program. Number of Associations Since Last Reset – For SUs - displays the total number of associations with any AU since the last reset, including duplicate associations with the same AU.
Menus and Parameters 2-5 The following parameter appears for GPS Modules only: Unit Status – Indicates the status of the GPS antenna. Either one of the following messages may be displayed: UTC is available; date..; time..: This message indicates that the GPS antenna has synchronized with the satellite system and that the BS-GU is functioning properly. The message may include an incorrect time and date, such as a date in 1999.
BreezeACCESS Version 4.3 Operations and Administration 2-6 includes some additional useful read-only information such as the Number of Hopping Frequencies (SU and AU). Unit Control Menu The Unit Control menu includes the following options: Reset Unit – Resets the BreezeACCESS unit and applies any changes made to the system parameters. Defaults Settings – Resets the unit to a predefined set of default parameters or to save the current configuration as Operator Defaults.
Menus and Parameters 2-7 Table 2-1: Parameters not changed after Set Complete/Partial Factory Defaults Parameter Complete Partial – Admin Partial Installer Unit Control Parameters √ Passwords √ √ Event Log Policy √ Auto Configuration Option √ IP Parameters IP Address √ √ Subnet Mask √ √ Default Gateway Address √ √ DHCP Option √ √ Access to DHCP √ √ ESSID √ √ Operator ESSID Option √ √ Operator ESSID √ √ Best AU Support √ √ Preferred AU MAC Address √ √ ACSE Option
BreezeACCESS Version 4.
Menus and Parameters 2-9 Set Complete Operator Defaults – Available only with Administrator access rights. Set the unit to its’ Operator Defaults configuration. After the next reset, all parameters will revert to their Operator Defaults values, except for the parameters that are marked in the “Complete” column of Table 2-1‚ page 2-7. Operator Defaults configuration can be defined by the Administrator (see Save Current Configuration As Operator Defaults below).
BreezeACCESS Version 4.3 Operations and Administration 2-10 Change Password – Changes the password(s). A user with Installer access rights can change the passwords for Read Only and Installer levels. A user with Administrator access rights can change the passwords of all levels. Valid values: A string of up to 8 printable ASCII characters. Table 1-1‚ page 1-2 lists the default passwords for each of the access levels.
Menus and Parameters 2-11 for storing it. Events are classified according to their severity level: Trace (lowest severity), Message, Warning, Error or Fatal (highest severity). The severity at which events are saved in the Event Log is configurable. Events from the configured severity and higher are saved and may be displayed upon request. Log history can be displayed up to the full number of current active events.
BreezeACCESS Version 4.3 Operations and Administration 2-12 c. The address of the TFTP server and the proper name of the configuration file must be configured in the DHCP server: The Server Address should be specified in the ‘sname’ field of the DHCP header. The code for this option is 66, and the minimum length is 1. It must include a legal IP address, with a maximum length of 64 characters (maximum length includes spaces. Extra characters will be ignored).
Menus and Parameters 2-13 Basic Configuration Menu The Basic Configuration menu includes all the parameters that are necessary for the initial installation and operation of the unit. Once the unit is properly installed and operational, other parameters can be configured either locally using the monitor program or remotely using Telnet, SNMP management or TFTP for loading to the unit a pre-prepared configuration file.
BreezeACCESS Version 4.
Menus and Parameters 2-15 Site Survey Menu The Site Survey menu provides various tests and counters for verifying the quality of the wireless link and the proper operation of the unit. These tests can be used to help determine where to position the units for optimal coverage, to align antennas and to assist in troubleshooting. Traffic Statistics (AU and SU) The traffic statistics can be used to monitor, interpret and analyze the wired and wireless links performance.
BreezeACCESS Version 4.3 Operations and Administration 2-16 Wireless Link Counters The unit transmits data frames received from the Ethernet port, as well as self-generated control and wireless management frames, to the wireless media. After transmission of a unicast frame, the unit waits for an acknowledgement (ACK) message from the receiving unit. Some control and wireless management frames as well as broadcast and multicast frames that are sent to more than one unit are not acknowledged.
Menus and Parameters 2-17 If the ACSE Option is enabled, then in addition to the total count, there are also separate counters for total number of data frames and voice (RTP) frames. The voice frames count includes fax frames. This is true also for Subscriber Units that do not support voice in cells where the ACSE Option in the AU is enabled. In this case the Voice count should be 0.
BreezeACCESS Version 4.3 Operations and Administration 2-18 Bad fragments received – Displays the number of frames received from the wireless media with errors (CRC errors). Duplicate frames discarded – Displays the number of frames discarded due to receiving multiple copies. If an acknowledge message was not received by the originating unit, the same data frame can be properly received twice (or more).
Menus and Parameters 2-19 Hopping Statistics Num The number of the information row, assigned automatically and sequentially by the program. Freq The hopping frequency, according to the hopping sequence. Rx The accumulated number of frames received at the specified frequency since last reset. Tx The accumulated number of frames transmitted successfully at the specified frequency since last reset. RTx The accumulated number of frames re-transmitted at the specified frequency since last reset.
BreezeACCESS Version 4.3 Operations and Administration 2-20 Start Sending – Starts transmission of ping frames. Stop Sending – Stops the transmission of ping frames. The test will end automatically once the number of pings that were sent has reached the value specified in the No. of Pings parameter (described above). The Stop Sending option can be used to end the test before completing the specified number of pings, or if continuous pinging was selected.
Menus and Parameters 2-21 Sp (Special): 5 Addresses that always exist: The MAC address of the AU (appears twice as it is learned from both the Ethernet and the wireless ports) Alvarion’s Multicast address (01:20:D6:00:00:01, also twice). The system handles this address as a Broadcast address.
BreezeACCESS Version 4.3 Operations and Administration 2-22 The SW version of the SU.
Menus and Parameters 2-23 Per-rate Counters (AU and SU) Resets or displays the per-rate counters. The per-rate counters display the number of frames (excluding retransmissions) transmitted since the last reset at each of the rates (1 Mbps, 2 Mbps, 3 Mbps) and the total number of frames that were retransmitted at each of the rates. In the AU the information is provided for each of the associated SUs, identified by their MAC address.
BreezeACCESS Version 4.3 Operations and Administration 2-24 AU Alarms (IF-based AU Only) The AU Alarms feature enables to identify and alert upon the detection of a potential problem in the outdoor unit of the AU, or another problem that causes significant degradation in the performance of the wireless link. When the AU Alarms Option is enabled, three types of tests are performed: Traffic Statistics tests, Power tests and Associations test.
Menus and Parameters 2-25 In addition, the Average Rate is also calculated for each of the above traffic statistics rates, using the formula Ra(t)=[Rc*1 +Ra(t-1)*5]/6, where: Rc - Current Rate Ra(t) - The new value of the Average Rate for the applicable rate. Ra(t-1) - the previous Average Rate of the applicable rate. For the first test cycle after reset (or after enabling the AU Alarms Option), Ra= Rc. For each traffic statistics type, three values can be configured: a.
BreezeACCESS Version 4.3 Operations and Administration 2-26 Based on the RSSI information responses from the SUs, the AU performs a calculation of the SU Rx Power Average Delta, defined as the average difference for all SUs between the last RSSI at the SU and the previous (one before last) RSSI. The average is calculated only for SUs that responded to both of the last two polling message.
Menus and Parameters 2-27 Association Tests If the AU was reset 3 times because no SU became associated with it, a No Associations critical alarm will be generated, provided that previously the AU was associated with at least Minimum Number Of SUs. An All Associations Lost major alarm is generated if no response was received by the AU to the last three polling messages, provided that prior to that, the average number of responding SUs was not lower than the Minimum Number Of SUs.
BreezeACCESS Version 4.3 Operations and Administration 2-28 All Associations Lost Alarm Severity: Major On Conditions: No response from any SU to the last 3 polling messages, and prior to that the average number of responding SUs was not lower than the Minimum Number Of SUs. Off Conditions: a. At lease one SU became associated with the AU -ORb. All alarms were cleared -ORc. AU Alarms Option was disabled Possible Problem: Unlocked synthesizer, very low Tx power or another major HW problem.
Menus and Parameters 2-29 High Retransmissions Rate Alarm Severity: Minor, Major On Conditions: Minor Severity Alarm: a. The Retransmissions Current Rate exceeds the Retransmissions Minor Alarm Threshold, and is higher than the Retransmissions Average Rate by at least Retransmissions Minor Alarm Minimum Delta, -ORb. The Retransmissions Current Rate has dropped below the Retransmissions Major Alarm Threshold but is still higher than the Retransmissions Minor Alarm Threshold.
BreezeACCESS Version 4.3 Operations and Administration 2-30 High Dropped Frames Rate Alarm Severity: Minor, Major On Conditions: Minor Severity Alarm: a. The Dropped Frames Current Rate exceeds the Dropped Frames Minor Alarm Threshold, and is higher than the Dropped Frames Average Rate by at least Dropped Frames Minor Alarm Minimum Delta, -ORb. The Dropped Frames Current Rate has dropped below the Dropped Frames Major Alarm Threshold, but is still higher than the Dropped Frames Minor Alarm Threshold.
Menus and Parameters 2-31 High CRC Error Rate Alarm Severity: Minor, Major On Conditions: Minor Severity Alarm: a. The CRC Error Current Rate exceeds the CRC Error Minor Alarm Threshold, and is higher than the CRC Error Average Rate by at least CRC Error Minor Alarm Minimum Delta, -ORb. The CRC Error Current Rate has dropped below the CRC Error Major Alarm Threshold but is still higher than the CRC Error Minor Alarm Threshold.
BreezeACCESS Version 4.3 Operations and Administration 2-32 High Duplicate Frames Rate Alarm Severity: Minor, Major On Conditions: Minor Severity Alarm: a. The Duplicate Frames Current Rate exceeds the Duplicate Frames Minor Alarm Threshold, and is higher than the Duplicate Frames Average Rate by at least Duplicate Frames Minor Alarm Minimum Delta, -ORb.
Menus and Parameters 2-33 The AU Alarms Menu The AU Alarms menu enables to configure relevant parameters and to view current statistics. The AU Alarms menu is available only with Administrator access rights, except for Show All AU Alarms Parameters and Data that is also available with Installer access rights. AU Alarms Option - Enables to enable or disable the AU Alarms feature. The default is Disable.
BreezeACCESS Version 4.
Menus and Parameters 2-35 Default value: 15 (dBm). Show AU Rx Power Test Parameters and Data - Displays the value of the AU Rx Power Decrease Threshold and the current AU Rx Power Average Delta. Responding SUs - a sub menu that includes the following options: Minimum Average Number Of SUs - Enables to define the minimum average number of SUs required for association tests.
BreezeACCESS Version 4.3 Operations and Administration 2-36 Advanced Configuration Menu The Advanced Configuration menu provides access to all the parameters, including the parameters that are available through the Basic Configuration menu.
Menus and Parameters 2-37 DHCP Client DHCP Options – Displays the current status of the DHCP (Dynamic Host Configuration Protocol) support, and allows selecting a new operation mode. The available options are: Disable – Use manual procedure for configuring the IP parameters. DHCP Only – Search for a DHCP Server and obtain the IP parameters from it (IP Address, Subnet Mask and Default Gateway Address). Automatic – Search for a DHCP Server for configuration of the IP parameters.
BreezeACCESS Version 4.3 Operations and Administration 2-38 NOTE: The same method for generating the basic hopping sequence (and the hopping shift mechanism) should be used for all units in the system to enable SUs to communicate with the AUs and to support radio planning that will provide minimal interference between neighboring sectors. The method for configuring the basic set of hopping frequencies depends on the frequency band and on other parameters: In products that operate in the 5.
Menus and Parameters 2-39 Table 2-3: ISM Basic Hopping Sequence Index Channel # Frequency (MHz) Index Channel # Frequency (MHz) Index Channel # Frequency (MHz) 1 2 5727 28 5 5730 55 15 5740 2 25 5750 29 39 5764 56 35 5760 3 64 5789 30 12 5737 57 67 5792 4 10 5735 31 36 5761 58 52 5777 5 45 5770 32 68 5793 59 58 5783 6 18 5743 33 9 5734 60 44 5769 7 73 5798 34 70 5795 61 50 5775 8 49 5774 35 77 5802 62 17 5742 9 21 5746 36
BreezeACCESS Version 4.3 Operations and Administration 2-40 the base sequence. For example, if the Frequency Offset is 10, channel 2 will be at 5737 MHz (5727 + 10). The permitted range in ISM US FCC is 0 to 45 (MHz). In ISM International mode the valid range is 0 to 70 (MHz). The default value is 0 (MHz).
Menus and Parameters 2-41 removed, including the frequencies that define the range boundaries. Erase All – Erases all the entries from the list. Scrambling Definition – Defines the method of organizing the selected frequencies to form the actual hopping sequence to be used. Proper organization of the hopping sequence is essential to guarantee minimal cross interference among several collocated AUs that use the same sequence with different Hopping Shift values. Scrambling Mode – Defines the scrambling mode.
BreezeACCESS Version 4.3 Operations and Administration 2-42 b.The index of each of the other channels is calculated by adding the Spanning Factor to the index of the previous channel. Note that the sequence is cyclic, meaning that adding 1 to the highest index in the sequence (Index=N where N is the number of channels in the sequence) will result in the first channel (Index=1).
Menus and Parameters 2-43 Valid values: 1 to Number of Hopping Frequencies minus 1, provided it meets the GCD requirement as described above. It is not recommended to use spanning factors of 1 and N-1, as they result in hopping on consecutive channel (assuming that the available channels are consecutive). In these cases the advantage of using frequency hopping is not fully utilized, since a narrow band interference may affect several consecutive hops.
BreezeACCESS Version 4.
Menus and Parameters Channels Spanning Factor 2-45 Hopping Sequences 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17 1, 3, 5, 7, 9, 11, 13, 15, 17, 2, 4, 6, 8, 10, 12, 14, 16 1, 4, 7, 10, 13, 16, 2, 5, 8, 11, 14, 17, 3, 6, 9, 12, 15 1, 5, 9, 13, 17, 4, 8, 12, 16, 3, 7, 11, 15, 2, 6, 10, 14 1, 6, 11, 16, 4, 9, 14, 2, 7, 12, 17, 5, 10, 15, 3, 8, 13 1, 7, 13, 2, 8, 14, 3, 9, 15, 4, 10, 16, 5, 11, 17, 6, 12 1, 8, 15, 5, 12, 2, 9, 16, 6, 13, 3, 10, 17, 7,
BreezeACCESS Version 4.
Menus and Parameters Channels 25 Spanning Factor 1 2 3 4 6 7 8 9 11 12 13 14 16 17 18 19 21 22 23 25 2-47 Hopping Sequences 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25 1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23, 25, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24 1, 4, 7, 10, 13, 16, 19, 22, 25, 3, 6, 9, 12, 15, 18, 21, 24, 2, 5, 8, 11, 14, 17, 20, 23 1, 5, 9, 13, 17, 21, 25, 4, 8, 12, 16, 20, 24, 3, 7, 11, 15, 19, 23, 2, 6, 10, 14, 18, 22 1, 7, 13, 19, 25, 6, 12,
BreezeACCESS Version 4.3 Operations and Administration 2-48 Show Flexible Hopping Parameters – Displays the following information: An updated list of the defined sub-bands and discrete frequencies to become effective after the next reset. A sub-band is defined by the first and last hopping frequency in a series of consecutive frequencies, with 3MHz separation between frequencies. An updated list of all the hopping frequencies to be used after the next reset.
Menus and Parameters 2-49 by the units in any two adjacent sectors will be 3 (e.g. 0, 3, 6, …) to minimize cross interference. Table 2-6: ISM Hopping Sequence, Hopping Shift=3 (Frequency Offset = 0).
BreezeACCESS Version 4.3 Operations and Administration 2-50 Enhanced Scrambling mode: In this mode the shift operation is performed on the channel indexes. The actual hopping channel is calculated by increasing the indexes of the basic hopping sequence by the value of the Hopping Shift. Note that the sequence is cyclic, meaning that adding 1 to the highest index in the sequence (Index=N where N is the number of channels in the sequence) will result in the first channel (Index=1).
Menus and Parameters 2-51 PS(j)={[P0(j)+S-1]mod(N)}+1 Where: S=Hopping Shift N=number of channels in the sequence (modulus) P0(j)=Channel no. j in the basic sequence (shift=0) PS(j)=Channel no. j in the actual sequence with hopping shift S Example: The basic hopping sequence is 1, 4, 7, 2, 5, 8, 3, 6 (Enhanced Scrambling, N=8, Spanning Factor=3).
BreezeACCESS Version 4.
Menus and Parameters 2-53 hopping sequence initialization and timing. If a BS-GU GPS module is not used for synchronization, then one AU must be specified as a Master unit and all other units must be specified as Slave units. When a BS-GU is used, all AUs must be configured to Slave mode.
BreezeACCESS Version 4.3 Operations and Administration 2-54 in the list displayed upon selecting either Show Air Interface Parameters or Show Basic Parameters options in the SU. In new installations where all units are configured with the same ESSID, Operator ESSID need not be used. The following parameters are available: Operator ESSID Option – Enables/disables the use of the Operator ESSID when communicating with SUs. The default is Enable. Operator ESSID – Defines the Operator ESSID.
Menus and Parameters 2-55 NOTE: Although the SU selects the Best AU based on long-term conditions prior to the decision time, it may not always be connected to the instantaneous Best AU at any given time. Note also that the decision is done only once during the scanning interval. The decision may not remain the optimal one for ever.
BreezeACCESS Version 4.3 Operations and Administration 2-56 its MAC address, it will associate with it and terminate the scanning process. If the preferred AU is not found, the SU will associate with an AU according to the decision reached using the best AU algorithm. Valid values: MAC address string The default value for the Preferred AU MAC Address is 00-00-00-00-00-00 (12 zeros), meaning that there is no preferred AU.
Menus and Parameters 2-57 If required for compliance with local regulations or other restrictions related to maximum allowable transmitted power. In addition to the ability to set the transmit power to a certain fixed level, BreezeACCESS units support an Automatic Transmit Power Control (ATPC) algorithm. The ATPC algorithm automatically adjusts the power level transmitted by each SU according to the actual level at which it is received by the AU.
BreezeACCESS Version 4.3 Operations and Administration 2-58 c. If the SU is associated with the AU but there are too many successive dropped frames, indicating that it transmits at a level that may be too low. The actual run-time value that is used to control the transmit power level is determined by the ATPC process. The allowed range is from 0 to 7. The effect of the Power Control Parameter on the actual power transmitted to the antenna port of the outdoor unit is according to Table 2-11 (5.
Menus and Parameters 2-59 ATPC Option: To enable or disable the Automatic Transmit Power Control (ATPC) algorithm. The default is Disable. Minimum RSSI Level: Enables you to define the lowest level at which you want each SU to be received at the AU (the lower limit of the optimal reception level range). Available values: -100 to 0dBm. Default value: -74 dBm for products operating in the 5.7 GHz band, and -79 dBm for products operating in the 5.
BreezeACCESS Version 4.3 Operations and Administration 2-60 that the SU will increase/decrease the value of the Transmit Power Control parameter by 2. Any value lower than 29 will result in Step=1. Available values: 1-100 (%) Default value: 1 ATPC Parameters in SU ATPC Option: To enable or disable the Automatic Transmit Power Control (ATPC) algorithm. The parameter takes effect immediately.
Menus and Parameters 2-61 recommended to also configure the Maximum Data Rate parameter when the Multi-Rate mechanism is enabled, to avoid unnecessary trials to transmit at higher rates when the probability of successful transmissions at these rates is low. In the SU, the link quality can be estimated based on the RSSI measurement, using the assumption that the link is more or less symmetrical and that this value is a good indication to the level at which the SU is received by the AU.
BreezeACCESS Version 4.3 Operations and Administration 2-62 Maximum Number of Associations – Defines the upper limit for the number of Subscriber Units that can be associated with the AU, in order to guarantee the required quality of service to the customers. Valid values: 0-512. Default value: 512. NOTE: There is no aging time for SUs.
Menus and Parameters 2-63 Maximum Voice Sessions – Applicable only for an AU that provides services to Subscriber Units with voice capabilities. When the ACSE voice scheduler option is enabled, this parameter is not applicable and instead the Maximum ACSE Voice Sessions parameter is used. The value of the Maximum Voice Sessions parameter specifies the maximum number of simultaneous voice sessions that can be conducted by the SUs associated with this AU.
BreezeACCESS Version 4.3 Operations and Administration 2-64 this parameter is not applicable and instead the Maximum Voice Sessions parameter (see page 2-63) is used. The value of the ACSE Maximum Voice Sessions parameter specifies the maximum number of simultaneous ACSE voice sessions that can be conducted by the SUs associated with this AU. If the number of active voice sessions reaches this number, any additional SU trying to initiate a voice session will not get a dial tone.
Menus and Parameters 2-65 The default is Active NOTE: When Best AU support is enabled, it is recommended to use Active Scanning. If passive scanning is used, the SU may not hear the best AU (or the preferred AU). The higher the number of hopping channels, the higher the probability that the SU will not hear the best (or preferred) AU when passive scanning is used. MAC Address Black List (AU only) - Enables to define units that are not authorized to receive services.
BreezeACCESS Version 4.3 Operations and Administration 2-66 The default selection is Disable. Network Management Parameters (AU, SU and GU) This feature allows protecting the unit from trials of unauthorized access by defining a set of IP addresses from which management of the unit (Telnet, TFTP, SNMP, ICMP) is allowed (excluding transmission of messages generated in the unit such as Traps or Ping Test frames).
Menus and Parameters 2-67 entries in the Set Network Management IP Addresses list. If the Access to Network Management parameter is configured to From Both Ethernet & Wireless Link, then there is no IP-address-based filtering on the Ethernet port. Activate Management IP Filter On Both Ethernet & Wlan Ports – Applicable with all options of the Access to Network Management parameter.
BreezeACCESS Version 4.
Menus and Parameters 2-69 Bridge Parameters (AU, SU and GU) The Bridge Parameters sub-menu includes the following parameters sets: Virtual LAN (VLAN) parameters ToS parameters Ethernet Broadcast Filtering parameters Other Bridging parameters Ports Control Parameters VLAN Parameters VLAN Support – Defines the parameters that are related to the VLAN-aware (Virtual LAN-aware) feature of BreezeACCESS units.
BreezeACCESS Version 4.3 Operations and Administration 2-70 VLAN ID-Management (AU, SU without voice and GU) – Applicable for all link types. Sets the VLAN ID for management frames, identifying remote stations for management purposes. This applies to all management applications using protocols such as SNMP, TFTP, ICMP (ping) and Telnet. All the servers/stations using these protocols must tag the management frames they send to the unit with the value of the VLAN ID – Management parameter.
Menus and Parameters 2-71 Telnet. All the servers/stations using these protocols must tag the frames they send to the unit with the value of the VLAN ID Voice & Management parameter. Valid values: 1 to 4094 or 65535 (No VLAN). Default value: 65535. If VLAN ID –Voice & Management is other than 65535: • Only tagged management frames with matching VLAN ID received on either the Ethernet or wireless link ports are forwarded to the unit.
BreezeACCESS Version 4.3 Operations and Administration 2-72 Transmit Tag Insert VID-M, PID-M If VID-M = 65535 and Voice Priority Tag option are enabled, Tag insert VID=0, PID-V. If VID-M not equal to 65535, insert VID-M and PID-V Legend: VID-M: VLAN ID - Voice and Management PID-M: VLAN Priority-Management PID-V: VLAN Priority-Voice VLAN Link Type (AU and SU) – Defines the link type, which actually defines the functionality of the VLAN-aware capability of the unit.
Menus and Parameters 2-73 If the VLAN Forwarding option is enabled, a received data frame with a VLAN ID that is not a member of the unit’s VLAN Forwarding List will be discarded. NOTE: If VLAN Forwarding is enabled, make sure to include in the Forwarding List the VLAN ID – Management (or VLAN ID - Voice & Management) of all units that should be managed via the wireless port of the unit.
BreezeACCESS Version 4.3 Operations and Administration 2-74 Table 2-18: VLAN Data Port Functionality Summary – Trunk Link Action Data Port (SU and AU) Accept from Ethernet Tagged frames. If Forwarding is enabled, only frames with VLAN ID values which are included in the Forwarding list are forwarded. Accept from Wireless Tagged frames. If Forwarding is enabled, only frames with VLAN ID values which are included in the Forwarding list are forwarded.
Menus and Parameters 2-75 VLAN Forwarding Support – Enables or disables the VLAN Forwarding feature. Available selections are Disable and Enable. The default selection is Disable. Add Forwarding VLAN ID – Adds a VLAN ID to the VLAN Forwarding List. One VLAN ID can be entered each time. The maximum number of VLAN IDs in the VLAN Forwarding List is 20. Valid values are 1 to 4094. Remove Forwarding VLAN ID – Removes a VLAN ID from the VLAN ID Forwarding List.
BreezeACCESS Version 4.3 Operations and Administration 2-76 Show VLAN ID Relaying List – Displays the values of the VLAN IDs that are included in the VLAN Relaying List. NOTE: If the VLAN ID Relaying List is empty and the VLAN Relaying Support is enabled, then all wireless link relayed data frames will be discarded. If the VLAN ID Relaying List and Forwarding List Support are both enabled, all the VLAN IDs configured in the Relaying List must also be configured in the Forwarding List.
Menus and Parameters 2-77 Valid values are 0-7. The default value is 0. NOTE: Packets Received from the Ethernet port with a ToS Precedence value higher than the ToS Precedence Threshold defined will be routed to the Mid queue. VLAN Priority – Management (AU, SU and GU)– Displays and sets the value of the VLAN Priority field for management frames in units with a VLAN ID- Management (or VLAN ID – Management & Voice) value other than 65535. In the unit all management frames are routed to the High queue.
BreezeACCESS Version 4.3 Operations and Administration 2-78 The default value is 4. Show VLAN Parameters – Displays the current values of the VLAN Support parameters. ToS Priority Parameters (AU and SU) ToS Priority – To set voice priority parameters to support end-to-end IPv4 Type of Service (ToS) Layer 3 prioritization according to RFC 791.
Menus and Parameters 2-79 Filter Options – Defines the Ethernet broadcast filtering functionality of the unit. The following options are available: Disable: No Ethernet broadcast filtering From Ethernet Only: Filter broadcast messages received from the Ethernet port From WLAN Only: Filter broadcast messages received from the wireless link port Both From Ethernet & WLAN: Filter broadcast messages received from both the Ethernet port and the wireless link port The default selection is Disable.
BreezeACCESS Version 4.3 Operations and Administration 2-80 Disable– ARP Broadcast messages are filtered or transmitted according to the general filtering criteria set by the Filter Options parameter. Enable– ARP Broadcast messages are transmitted regardless of the selected value of the Filter Options parameter. The default selection is Enable. Other Bridging Parameters LAN to Wireless Link Bridging Mode (AU only) – Controls the flow of information from the Ethernet backbone to the wireless media.
Menus and Parameters 2-81 Ports Control (SU only) - To enable/disable the Ethernet and/or Voice port. The Ports Control submenu includes the following options: Ethernet Port Control - To enable/disable non-management traffic to/from the Ethernet port. All current data sessions will be terminated. The unit may still be managed via the Ethernet port even when it is disabled for data traffic. The default selection is Enable. Voice Port Control (SU with voice support) - To enable/disable the voice port.
BreezeACCESS Version 4.3 Operations and Administration 2-82 Performance Parameters (AU and SU) The Performance Parameters menu includes the following parameters: RTS Threshold – Defines the minimal frame size to require RTS/CTS (Request To Send/Clear To Send) handshake. Frames with a size below the RTS Threshold value are transmitted directly to the wireless link without being preceded with RTS frames.
Menus and Parameters 2-83 Minimum Contention Window – The BreezeACCESS system uses a special mechanism based on detecting the presence of a carrier signal (Carrier Sense Multiple Access-CSMA) and analyzing the information contained in the transmissions of the AU to estimate the activity of other SUs served by the same AU. The target is to minimize collisions in the wireless media resulting from trials of more than one unit to transmit at the same time.
BreezeACCESS Version 4.3 Operations and Administration 2-84 different rates. The decision on the rate of each transmission (first attempt) is based on counting transmissions, retransmissions and successful windows. A window is defined as N consecutive transmission or retransmission attempts, defined by the Multi-Rate Decision Window Size parameter. A successful window is a window in which the number of failed transmissions is not higher than a defined threshold.
Menus and Parameters 2-85 Dwell Time (AU only) – The time spent on a radio channel before hopping to the next channel according to the operational hopping sequence. The allowed selections are 32, 64 and 128 Kilo-microseconds. The default value is 128 Kilo-microseconds. When the ACSE Option is enabled this parameter is not applicable and the dwell time is the ACSE Dwell Time, set to a fixed value of 60 milliseconds.
BreezeACCESS Version 4.3 Operations and Administration 2-86 Level, it shall be considered as interference and it becomes the updated Current Noise Floor. Carrier to Interference Difference Level is the minimal difference between the Current Noise Floor and the level of a signal that will be defined as a “good” one. This algorithm allows the unit to identify and track temporary high level interference and to adjust the decision threshold accordingly.
Menus and Parameters 2-87 the User Defined Addresses Only option was selected in the User Filtering Option above. The default for all addresses is 0.0.0.0. Set User Filter Mask – Displays the current masks. Allows you to enter subnet masks for each of the User Filter IP Address entries. The default for all subnet masks is 255.0.0.0. Set User Filter Range – Defines a range of addresses for each of the User Filter IP Address entries (the range includes the base address). Valid values: 0 – 255.
BreezeACCESS Version 4.3 Operations and Administration 2-88 degradation has been incorporated into the AU, ensuring that the degradation of performance for each individual subscriber will be proportional to its CIR. The MIR/CIR algorithm uses buffers to control the flow of data. To average the performance over time, a special Burst Duration algorithm is employed to enable higher transmission rates after a period of inactivity.
Menus and Parameters 2-89 Valid values are from 0 to 2200Kbps. The default value is 64Kbps. NOTE: The value of the MIR must be higher than the value of the applicable CIR. The system will not accept a MIR value that is lower than the current CIR value, and vice versa. Maximum Burst Duration (SU and AU) – Sets the maximum time for accumulating burst transmission rights according to the Burst Duration algorithm. Valid values: 0 – 2000 (milliseconds).
BreezeACCESS Version 4.3 Operations and Administration 2-90 Option is enabled, the MIR/CIR algorithm is overridden and is forced to operate with MIR values only (e.g. the AU attempts to enable all SUs to transmit/receive information at the specified MIR value. When enabled, the graceful degradation algorithm, which is a part of the CIR/MIR algorithm, is also disabled. The default is Disable. Show MIR/CIR Parameters – Displays the current values of the MIR and CIR parameters.
Menus and Parameters 2-91 to allow access for the user. This always includes verification of the password, but can also specify the client(s) or port(s) to which the user is allowed access. In the BreezeACCESS system there is a RADIUS NAS (Network Access Server) implemented in each Subscriber Unit. The RADIUS server can be used for authentication purposes only, for accounting purposes only, or for both authentication and accounting purposes. The RADIUS Parameters menu includes three sub-menus: a.
BreezeACCESS Version 4.3 Operations and Administration 2-92 (CIR/MIR, Telephone number etc.). If the authentication is not successful, the data and voice ports of the SU will be blocked. Authentication Option – To enable or disable the use of RADIUS for authentication. When this option is enabled and the RADIUS Server Authentication IP Address is configured to an address other than 0.0.0.0., the SU enables the RADIUS authentication feature.
Menus and Parameters 2-93 The default value is 1813 (RFC requirement). Accounting Interval – Specifies the interval in seconds between two consecutive transmissions of accounting records. Valid values are from 60 to 6000 seconds (1 to 100 minutes). The default value is 90 seconds. Show Accounting Parameters – Displays the current values of the Accounting parameters. RADIUS Record Structure Each RADIUS Accounting message includes a Session ID and up to 11 Ethernet Specific records.
BreezeACCESS Version 4.3 Operations and Administration 2-94 Table 2-21: Ethernet Vendor Specific Record Structure (Vendor Specific ID is 710) Field Format Description Traffic Type 1 hexadecimal digit Data (0)/Management (1)/Voice (2). VLAN ID 3 hexadecimal digits VLAN ID. Layer 3 Protocol 4 hexadecimal digits Third layer protocol type (IP, ARP). Remote IP Address xxx.xxx.xxx.xxx (decimal format) The remote IP Address.
Menus and Parameters 2-95 Shared Key: Authentication enabled. The authentication messages are encrypted. An SU configured to use Shared Key can be authenticated only by an AU configured to use Shared Key, provided they both use the same WEP Key. Both the WEP Key number and the WEP Key should be identical at both sides of the link. Support All (AU only): The AU authenticates all SUs, regardless of the Authentication Algorithm and WEP Key configured in the SU.
BreezeACCESS Version 4.3 Operations and Administration 2-96 NOTE: It is recommended to change the WEP Keys periodically, to enhance system security. Voice Parameters (Subscriber Units with Voice Support Only) The parameters in the Voice Parameters menu include the following options: Volume – Sets the gain of the voice signal to the earphone. Available range is 0 dB to -20 dB in 1 dB steps. The default value is -3 dB. Echo Cancellation – Enables or disables the built-in echo cancellation feature.
Menus and Parameters 2-97 The allowed range differs among codecs, in accordance with the different packet sizes (30 ms for G723.1, 10 ms for G729 and 5 ms for G711). The valid values and default values are: G723 Frames Per Packet – Valid range 1-8, Default value is 2 G729 Frames Per Packet – Valid range is 1-12, Default value is 6. If upgrading from a previous version, this value must be set to 6 if ACSE Option is enabled.
BreezeACCESS Version 4.3 Operations and Administration 2-98 into the IP address and to register its own phone number and IP address with the Gatekeeper. The default selection is Disable. GateKeeper/GateWay IP Address – Specifies the IP address of the Gateway/Gatekeeper. If the Gatekeeper Option parameter (see above) is set to Enable, an IP address must be specified. The default value is 0.0.0.0. Alternate Gatekeeper Option - Enables or disables the Alternate Gatekeeper feature.
Menus and Parameters 2-99 assumed to be the destination IP address. 12- and 3-digit numbers are allowed. 3- digit numbers are used to dial to stations in the same subnet, and 12- digit number are used to dial to any IP address. If a 3-digit number is dialed the Setup message is sent to the corresponding IP address in the local subnet. When dialing a 12-digit number (e.g. abcdefghijkl), the Setup message is sent directly to the IP address abc.def.ghi.jkl.
BreezeACCESS Version 4.3 Operations and Administration 2-100 NOTE: This information element is encoded according to Figure 4-11/Q.931 and Table 4-6/Q.931. The SU support only H323 Speech traffic and a change of the default value is not recommended. A change will be needed only as result of special PSTN switch requirements. Dialing Prefix Parameters – Supports definition of prefix strings indicating an inter-regional or international call.
Menus and Parameters 2-101 Default value: 0. Registration TTL – Defines the registration Time To Live. Registration is the process by which an endpoint informs the Gatekeeper of its Transport Addresses and alias addresses. Registration must occur before any calls are attempted and may occur periodically as necessary (for example, at endpoint power-up). After Registration process has finished an endpoint will no longer send Registration Request (RRQ) messages.
BreezeACCESS Version 4.3 Operations and Administration 2-102 Fax Relay – Defines the use of T.38 protocol for relaying fax messages. T.38 is a protocol dedicated to fax. When the Fax Relay Option is enabled, fax signals are demodulated at the voice/fax gateway and sent over the IP network as IP fax packets (IFP) using UDP. A redundancy mechanism can be employed to restore IFP fax data packets. At the other end of the IP network, the remote gateway decodes IP fax packets and regenerates fax signals.
Menus and Parameters 2-103 1200-baud tone modulation in accordance with Bellcore 202 standard. The Caller ID parameter is supported only by units using a Voice card HW revision D and higher. The following options are available: Disable ETSI DT-AS: CID signaling in accordance with ETSI ETS 300 659 -1, using Dual Tone Alerting Signal to indicated to the called terminal that CID data transmission is to be expected.
BreezeACCESS Version 4.3 Operations and Administration 2-104 Upon enabling overlap sending, the settings of other dialing parameters are overridden as follows: a. IP Dialing Option, Dialing Prefix Option and Stop Dialing Indicator are disabled even if the applicable parameter is set to Enable. b. Automatic Prefix is not used and Stop Dialing Timeout has no effect. The default selection is Disable.
Menus and Parameters 2-105 Error Tone – Defines the tone transmitted to the earphone to indicate that the system cannot currently support the call (e.g. if for any reason the call was disconnected because of a problem in the wireless link or incompatible capabilities) or if the user did not hang up after exceeding the specified duration of the Dial, Ring Back, Busy or Congestion Tones.
BreezeACCESS Version 4.3 Operations and Administration 2-106 Cadence Off – The silence time (on) in the ringing-silence sequence of the Ringer. Valid values are 100 – 10,000 milliseconds. Duration - The maximum duration of activating the ringer. Ringing will cease upon detecting off-hook condition. Valid values are 0 – 10,000 seconds. Timeouts – Defines the following timeouts: Min. Flash Detect Timeout and Max.
Menus and Parameters 2-107 Table 2-23: Parameters of Call Progress Tones and Ringer - USA Frequency 1 Frequency 2 Cadence On (ms) Duration (s) Tone Freq (Hz) Level (dB) Freq (Hz) Level (dB) Off (ms) Dial Tone 350 -13 440 -13 Ring Back 440 -19 480 -19 1000 3000 60 Busy 480 -24 620 -24 500 500 15 Congestion 480 -24 620 -24 1000 1000 0 Error 480 -24 620 -24 200 200 0 High Level Error 0 0 0 0 0 0 0 Ring Frequency 20 1000 3000 60 15 Table 2-24: Param
BreezeACCESS Version 4.
Menus and Parameters 2-109 Table 2-29: Timeouts Min. Flash Detect (ms) Max Flash Detect (ms) Disconnect (ms) Inter-digit (ms) Called Party Release (s) Germany 120 1000 1000 100 0 USA 120 1000 1000 100 0 Sweden 120 1000 1000 100 0 France 120 1000 1000 100 0 United Kingdom 120 1000 1000 100 0 Belgium 120 1000 1000 100 0 Chile 220 320 320 500 60 Country BreezeACCESS Version 4.
BreezeACCESS Version 4.3 Operations and Administration 2-110 Hopping Parameters (GU) The Hopping Parameters Menu allows configuration of the hopping mechanism. The GPS modules deliver signals to the Access Units that insure that their hopping patterns are fully synchronized. This includes synchronizing the time each unit starts a new hop and ensuring that units start the hopping sequence simultaneously.
Menus and Parameters 2-111 synchronization signals will also be transferred to the SYNC OUT port. b. If a BS-GU is a "slave", it will use the synchronization signals it receives from the "master" via the SYNC IN port. It will also transfer these signals to its SYNC OUT port for use by the next slave module if applicable. A slave module continuously monitors the lines from the GPS antenna in its SYNC IN port.
BreezeACCESS Version 4.3 Operations and Administration 2-112 Alarm Parameters (GU) The GU module serves also as the alarms control unit for the BreezeACCESS system and auxiliary equipment. It has dry contact connections to 4 external alarm inputs (Alarm In 1 through Alarm In 4), that turn on upon contact closure.
Menus and Parameters 2-113 Each Alarms Out Name can contain up to 31 printable ASCII characters (case sensitive). The default names are Alarm Out 1 through Alarm Out 3. Automatic Alarms Out Definition The Automatic Alarms Out Definition menu allows you to define the conditions under which each of the 3 Alarms Outs is to be activated (when operating in Automatic mode). The available options for each of the three Alarms Out are: 1 – Activate if Alarm In 1 turns ON. 2 – Activate if Alarm In 2 turns ON.
BreezeACCESS Version 4.3 Operations and Administration 2-114 Alarms In Names And Status Displays the names and current status (ON or OFF) for all Alarm In indications, including “internal” alarms, as follows: Alarm In 1 through Alarm In 4: Name according to the name defined in the Alarms In Names Menu. Alarm In 5: GPS Antenna Status. Alarm In 6: NA (reserved for future use).
BreezeACCESS V Version 4.3 Revision 4.
Appendix A: Configuration Download/Upload This appendix describes the method of configuring a large number of BreezeACCESS units at once.
BreezeACCESS Version 4.3 System Manual A-2 The Configuration Download/Upload feature in BreezeACCESS units simplifies the task of remotely configuring a large number of units using TFTP protocol. By downloading the configuration file to a PC it is possible to view all the parameters configured at the unit, as it is a plain text ASCII file. It is necessary to edit the file by a using simple editor and to remove certain parameters or change their values prior to uploading the configuration to another unit.
Appendix B: Software Version Loading Procedure General Firmware upgrades to the unit's FLASH memory are performed by a simple loading procedure using a TFTP application. Before performing an upgrade procedure, be sure you have the correct files and latest instructions. NOTE: Shutting down power to the unit before completion of the loading procedure may cause the unit to be inoperable. Verify that you have IP connectivity to the unit to be loaded with a new version.
BreezeACCESS Version 4.3 System Manual B-2 6. To verify the connection, ping the unit’s IP address. Verify that ping replies are being received. The procedure to be used depends on the unit’s FLASH memory type. Identify the FLASH memory type by using the monitor program, connecting the PC to the unit either directly or via Telnet. From the Main Menu, select 1 – Info Screens. From the Info Screen menu select 1 – Show Unit Status.
Appendix B B-3 NOTE: If you are upgrading a Subscriber Unit which is not associated with an AU, the unit will reset every five minutes (approximately) and the following message will be displayed: FTL: file src\wpscan.c line 262 Too large number of scanning attempts The unit will reset and it will take more than a minute before you can re-establish the connection to it.
BreezeACCESS Version 4.3 System Manual B-4 1. From the Flash Memory Control menu select 2 - Use Current Version After Reset. The Use Current Version After Reset menu opens. 2. Select 1 – Set As Default Now and press ENTER. This will actually cause the names of the two versions to switch. The previous Shadow version will now be called Current and vise versa. The following message will be displayed: UP (DOWN) Image FLASH will be operational (UP or DOWN refers to the location in the flash memory).
Appendix B B-5 NOTE: If you are upgrading a Subscriber Unit which is not associated with an AU, the unit will reset every five minute (approximately) and the following message will be displayed: FTL: file src\wpscan.c line 262 Too large number of scanning attempts The unit will reset and it will take more than a minute before you can re-establish the connection to it.
BreezeACCESS Version 4.3 System Manual B-6 1. From the Flash Memory Control menu select 2 - Use Current Version After Reset. The Use Current Version After Reset menu opens. 2. Select 1 – Set As Default Now and press ENTER. This will actually cause the names of the two versions to switch. The previous Shadow version will now be called Current and vise versa. The following message will be displayed: UP (DOWN) Image FLASH will be operational (UP or DOWN refers to the location in the flash memory).
Appendix C: Supported MIBs and Traps BreezeACCESS agents support the following MIBs: MIB-II (RFC1213) BRIDGE-MIB (RFC1286) BreezeCOM brzAccessMib BreezeCOM brzPhoneMib BreezeCOM brznetmib
BreezeACCESS Version 4.3 System Manual C-2 BreezeACCESS System Object Identifiers Path: breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.710 {(iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) breezecom(710)} breezecomNewOID {breezecom 10} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.10 breezecomBreezeACCESSproducts {breezecomNewOID 2} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.10.2 breezecomBreezeACCESS_ACCESS {breezecomBreezeACCESSproducts 1} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.10.2.
Appendix C C-3 Object OID (Location in parenthesis) Description breezecomAU_I breezecomBreezeACCESS_ACCESS 21 (710.10.2.1.21) AU-I breezecomSU_BS breezecomBreezeACCESS_ACCESS 22 (710.10.2.1.22) SU-BS breezecomAU_BS_WA breezecomBreezeACCESS_ACCESS 23 (710.10.2.1.23) AU-BS-WA breezecomGU_BS breezecomBreezeACCESS_GENERAL 1 (710.10.2.2.1) GU-BS brzAccessMIB Path: breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.
BreezeACCESS Version 4.3 System Manual C-4 MIB Parameter (Location in Parenthesis) Description Values/Range *RunTimeMirCirOption 710.3.3.1.9 (*ServiceParameters 9) Applicable to SU only. Indicates the actual status of the MIR/CIR option, which may be different from the setting of this parameter in the SU since it is controlled by the AU. Integer disable (0) enable (1) na (255) *MirOnlyOption 710.3.3.1.10 (*ServiceParameters 10) Applicable only to AU when CIR/MIR option is enabled.
Appendix C C-5 RADIUS Authentication Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *RadiusAuthParameters 710.3.3. 21 (brzAccessMib 21) Applicable to SU only. RADIUS Authentication parameters. *RadiusAuthOption 710.3.3. 21.1 (*RadiusAuthParameters 1) Applicable to SU only. Enables or disables the RADIUS Authentication support feature. Integer disable (0) enable (1) na (255) * RadiusServerAuthIpAddress 710.3.3. 21.2 (*RadiusAuthParameters 2) Applicable to SU only.
BreezeACCESS Version 4.3 System Manual C-6 MIB Parameter (Location in Parenthesis) Description Values/Range *DeleteOneUserFilter 710.3.3.2.3 (*UserFilterParams 3) Applicable to SU only. Deletes a single selected entry from the IP Filter Table. Integer off (0) firstEntry (1) secondEntry (2) thirdEntry (3) fourthEntry (4) fifthEntry (5) sixthEntry (6) seventhEntry (7) eighthEntry (8) na (255) *DeleteAllUserFilters 710.3.3.2.4 (*UserFilterParams 4) Applicable to SU only.
Appendix C C-7 Network Management Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *NwMngParameters 710.3.3. 4 (brzAccessMib 4) Network Management parameters. *AccessToNwMng 710.3.3. 4.1 (*NwMngParameters 1) Applicable to AU and SU. The port to be used for remote management. wlanOnly: Management E from Wireless port only. ethOnly: Management enabled from Ethernet port only. bothWlanEth: Management enabled from both Wireless and Ethernet ports.
BreezeACCESS Version 4.3 System Manual C-8 MIB Parameter (Location in Parenthesis) Description Values/Range *DeleteAllTrapAddrs 710.3.3.4.9 (*NwMngParameters 9) Applicable to AU, SU and GU. Deletes all entries from the Management Trap Table. *PerTrapControl 710.3.3.4.10 (*NwMngParameters 10) Applicable to AU, SU and GU. Per Trap Control parameters. *SendSUAssociatedAUTrap 710.3.3.4.10.1 (*PerTrapControl 1) Applicable to AU only. Enables\Disables the sending of brzaccSUassociatedAUTRAP.
Appendix C C-9 Bridge Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *BridgeParameters 710.3.3. 5 (brzAccessMib.5) Bridge parameters. *EthBroadcastFiltering 710.3.3. 5.1 (*BridgeParameters 1) Applicable to SU only. Enables/disables the filtering of Ethernet (layer2) broadcasts. disable: No filtering. ethOnly: Filter broadcasts received on the Ethernet port only. wlanOnly: Filter broadcasts received on the Wlan port only.
BreezeACCESS Version 4.3 System Manual C-10 MIB Parameter (Location in Parenthesis) Description Values/Range *VlanRelayingEntry 710.3.3. 5.2.8.2.1 (*VlanRelayingTable 1) Applicable to AU only. A VLAN Relaying Table entry. (applicable in Trunk links only). Not accessible. *VlanRelayingIdx 710.3.3. 5.2.8.2.1.1 (*VlanRelayingEntry) 1 Applicable to AU only. A read only table index for a VLAN entry in the VLAN Relaying Table. Integer 1 - 20 *VlanIdRelaying 710.3.3. 5.2.8.2.1.
Appendix C C-11 MIB Parameter (Location in Parenthesis) Description Values/Range *PortsControl 710.3.3. 5.9 (*BridgeParameters 9) Applicable to SU only. Port Control parameters *EthernetPortControl 710.3.3. 5.9.1 (*PortsControl 1) Applicable to SU only. Enable/disable the Ethernet port. When disabled, only data frames are blocked. Management frames are accepted. Integer disable (0) *VoicePortControl Applicable to SU with voice only. Enable/ Integer 710.3.3. 5.9.
BreezeACCESS Version 4.3 System Manual C-12 MIB Parameter (Location in Parenthesis) Description Values/Range *TransmitDiversity 710.3.3. 6.4 (*AirInterface 4) Applicable to SU-R, SU-I and AU-I units only. Enables the selection of the antenna(s) to be used for transmission. Integer use2Antennasn (0) antenna1 (1) antenna2 (2) na (255) *HoppingSequence 710.3.3. 6.5 (*AirInterface 5) Applicable to AU in BreezeACCESS II family only. Determines the hopping sequence to be used.
Appendix C MIB Parameter (Location in Parenthesis) *HoppingBands 710.3.3. 6.9 (*AirInterface 9) C-13 Description Values/Range Applicable to SU and AU only. In BreezeACCESS II units set in the factory to “Country Standard Protected” this is read-only, showing the Country Standard set in the factory. Integer na (255) The available values represent settings that are dependent on the specific radio band.
BreezeACCESS Version 4.3 System Manual C-14 MIB Parameter (Location in Parenthesis) Description *HoppingBands (continued) Values/Range BreezeACCESS 3.5b, 3.
Appendix C MIB Parameter (Location in Parenthesis) C-15 Description Values/Range *AddSubBand 710.3.3. 6.15.1 (*FlexSubBandDef 1) Applicable to SU and AU only. In BreezeACCESS II, V and MMDS families it adds sub-bands (f1-f2) or discrete frequencies to the list of sub-bands/frequencies to be used for generating the basic Hopping Sequence after the next reset. In BreezeACCESS XL it defines a new set of sub-bands/frequencies to be used for generating the basic Hopping Sequence after the next reset.
BreezeACCESS Version 4.3 System Manual C-16 MIB Parameter (Location in Parenthesis) Description Values/Range *ChannelSpacing 710.3.3. 6.15.5 (*FlexSubBandDef 5) Applicable to SU and AU in BreezeACCESS XL family only. Applicable only in Flexible Hopping Definition mode. Defines the minimum distances between two frequencies. (Not available in some products that only support a 2MHz Channel Spacing) Integer space1_75MHz (0) space1MHz (1) space2MHz (2) na (255) *AddFlexHopChannels 710.3.3. 6.15.
Appendix C MIB Parameter (Location in Parenthesis) C-17 Description Values/Range *ScrambledSeqTableIdx 710.3.3. 6.15. 9.5.1.1 (**ScrambledSeqEntry 1) Applicable to SU and AU only. Readonly. A Scrambled Sequence Table entry index. Integer *ScrambledSeqFreqIdx 710.3.3. 6.15. 9.5.1.2 (**ScrambledSeqEntry 2) Applicable to SU and AU only. Readonly. A Frequency Index in the Scrambled Sequence Table. DisplayString (SIZE(10)) *CallAgingTime 710.3.3. 6.16 (*AirInterface 16) Applicable to AU only.
BreezeACCESS Version 4.3 System Manual C-18 MIB Parameter (Location in Parenthesis) Description Values/Range *OperatorESSID 710.3.3. 6.21 (*AirInterface 21) Applicable to AU only. A secondary ESSID to support upgrade of existing installations. All AUs in the region should be configured to the same Operator ESSID to allow a new SU to associate with any AU. Accessible only with SNMP Write Community DisplayString (SIZE(31)) Up to 31 printable ASCII characters, case sensitive. *RunTimeESSID 710.3.3. 6.
Appendix C MIB Parameter (Location in Parenthesis) C-19 Description Values/Range *TransmitLevel 710.3.3. 6.24 (*AirInterface 24) Applicable only to SU-I and AU-I units with HW version D and higher. Sets the level in dBm of the transmitted power at the antenna port. * brzaccAtpc 710.3.3. 6.25 (*AirInterface 25) ATPC Parameters *AtpcOption 710.3.3. 6.25.1 (*Atpc 1) Applicable to IF based units and SUR-3.5ab units only. Enabling/ disabling the ATPC Algorithm.
BreezeACCESS Version 4.3 System Manual C-20 MIB Parameter (Location in Parenthesis) Description Values/Range *ACSEOption 710.3.3. 6.27.1 (*ACSEParameters 1) Applicable for AU, SU and GU. Read-only in the SU. Disable/enable the ACSE Voice Scheduler mechanism. Integer disable (0) enable (1) *ACSEDwellTime 710.3.3. 6.27.2 (*ACSEParameters 2) Applicable for AU, SU and GU. Read-only. The dwell time when the *ACSEOption is enabled. Currently set to 60 milliseconds.
Appendix C MIB Parameter (Location in Parenthesis) C-21 Description Values/Range *SPFreqs 710.3.3. 6.31.2 (* SiteProprietary 2) Site Proprietary frequencies parameters. *SPFreqsTable 710.3.3. 6.31.2.1 (*SPFreqs 1) A table of frequencies in the Site Proprietary hopping sets. Not accessible. sPFreqsEntry 710.3.3. 6.31.2.1.1 (*SPFreqsTable 1) An entry in the table of frequencies in the Site Proprietary hopping sets. Not accessible. sPFreqIdx 710.3.3. 6.31.2.1.1.
BreezeACCESS Version 4.3 System Manual C-22 MIB Parameter (Location in Parenthesis) Description Values/Range *ScanningMode 710.3.3.6.35 (*AirInterface 35) Applicable to SU only. Not applicable if *ACSEOption is enabled. Sets the scanning mode. passive (1) active (2) na (255) *SendRoamingSNAP 710.3.3.6.37 (*AirInterface 37) Applicable to all SUs, except to SUBD and SU-BD1V. Disables/enables the Send Roaming SNAP feature. Integer disable (0) enable (1) na (255) *AUTransmissionRateContro l710.3.3.6.
Appendix C MIB Parameter (Location in Parenthesis) C-23 Description Values/Range *CarrierSenseLevel 710.3.3. 7.7 (*PerformanceParams 7) Applicable to SU and AU. Threshold level for decision on existence of a carrier signal, indicating a transmission from another unit. DisplayString -100 to -40 (dB) *DwellTime 710.3.3. 7.9 (*PerformanceParams 9) Applicable to AU and GU. The time spent on each radio channel (hop). Applicable only when the *ACSEOption is disabled.
BreezeACCESS Version 4.3 System Manual C-24 Site Survey Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *SiteSurvey 710.3.3. 8 (brzAccessMib 8) PerHopStatisticsTable 710.3.3. 8.1 (*SiteSurvey 1) Applicable to SU and AU. Statistics accumulated since last reset and average RSSI per frequency for all hopping frequencies in the (sequence). Not Accessible. hopSeqEntry 710.3.3. 8.1.1 (perHopStatisticsTable 1) Applicable to SU and AU. A Per Hop Statistics Table entry.
Appendix C MIB Parameter (Location in Parenthesis) C-25 Description Values/Range *TotalRxFramesFromWireless 710.3.3. 8.2.3.2 (*WlanCounters 2) Applicable to SU and AU. Read-only. The total number of frames that were received from the wireless media. The count includes data and control and management frames, including beacons received from the AU. The count does not include frames that were discarded internally, bad frames and duplicate frames. Counter *TotalRetransmittedFragments 710.3.3. 8.2.3.
BreezeACCESS Version 4.3 System Manual C-26 MIB Parameter (Location in Parenthesis) Description Values/Range *SubmittedFramesLow 710.3.3. 8.2.3.11 (*WlanCounters 11) Applicable to SU and AU. Read-only. Counts the number of frames submitted to the bridge via the Low queue for transmission to the wireless media. When the ACSE Option is enabled, it counts data and RTP frames. When the ACSE Option is disabled, it counts only data frames. Counter *SubmittedFramesVoice 710.3.3. 8.2.3.
Appendix C MIB Parameter (Location in Parenthesis) C-27 Description Values/Range *TotalTxErrorsAckTOut 710.3.3. 8.2.3.23 (*WlanCounters 23) Applicable to SU and AU. Read-only. The number of transmit errors that have occurred because of an Acknowledge Timeout–a frame that was not acknowledged within the time defined by the Acknowledge Delay Limit parameter. Counter *TotalTxErrorsFail 710.3.3. 8.2.3.24 (*WlanCounters 24) Applicable to SU and AU. Read-only.
BreezeACCESS Version 4.3 System Manual C-28 MIB Parameter (Location in Parenthesis) Description Values/Range *VoiceTrafficTxFrames 710.3.3. 8.2.4.1 (*VoiceCounters 1) Applicable to SU with voice support only. Read-only. Counts the number of voice frames, including fax and T.38 redundant frames, that were transmitted to the wireless link. Counter *VoiceTrafficRxFrames 710.3.3. 8.2.4.2 (*VoiceCounters 2) Applicable to SU with voice support only. Read-only.
Appendix C MIB Parameter (Location in Parenthesis) C-29 Description Values/Range *PerHopStatistics 710.3.3. 8.4 (*SiteSurvey 4) Applicable to SU and AU. *ResetPerHopStatistics 710.3.3. 8.4.1 (*PerHopStatistics 1) Applicable to SU and AU. Reset the Per Hop Statistics counters. *MacAddressDatabase 710.3.3. 8.5 (*SiteSurvey 5) Applicable to AU only. Database by MAC Addresses for all SUs associated with the AU.
BreezeACCESS Version 4.3 System Manual C-30 MIB Parameter (Location in Parenthesis) Description Values/Range *AdbRTx1M 710.3.3. 8.5.2.1.10 (*AdbEntry 10) Applicable to AU Only. Read-only. Counts the total number of frames that were retransmitted to the SU over the wireless link at 1Mbps. Counter *AdbRTx2M 710.3.3. 8.5.2.1.11 (*AdbEntry 11) Applicable to AU Only. Read-only. Counts the total number of frames that were retransmitted to the SU over the wireless link at 2Mbps. Counter *AdbRTx3M 710.3.
Appendix C MIB Parameter (Location in Parenthesis) C-31 Description Values/Range AtpcTransmittedMessages 710.3.3. 8.6.2 (*AtpcCounters 2) Applicable to IF based AU. The total number of ATPC messages transmitted by the unit since last reset. Integer AtpcReceivedMessages 710.3.3. 8.6.3 (*AtpcCounters 3) Applicable to SU units only. The number of ATPC messages received by the unit since last reset regardless of whether the unit supports ATPC. Integer *AUAlarms 710.3.3. 8.
BreezeACCESS Version 4.3 System Manual C-32 MIB Parameter (Location in Parenthesis) Description Values/Range *MinorAlarmThreshold 710.3.3. 8.7.4.1.1.5 (*TrafficStatisticsEntry 5) Applicable to IF-based AU only. Read-write. The threshold for activating a minor severity alarm for the relevant statistics type.
Appendix C C-33 MIB Parameter (Location in Parenthesis) Description Values/Range Integer 1 – 254 (SUs) *MinimumAverageNumberOfSUs 710.3.3. 8.7.7.3 (*RespondingSUs 3) Applicable to IF-based AU only. The minimum average number of SUs required for association tests *AUAlarmsStatus 710.3.3. 8.7.8 (*AUAlarms 8) Applicable to IF-based AU only. Alarms Status parameters. *AlarmsStatusTable 710.3.3. 8.7.8.1 (*AUAlarmsStatus 1) Applicable to IF-based AU only. Not accessible.
BreezeACCESS Version 4.3 System Manual C-34 Unit Control Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *UnitControl 710.3.3. 10 (brzAccessMib 10) *ResetUnit 710.3.3. 10.1 (*UnitControl 1) Applicable to all products. Resets the unit and applies new parameter values. Integer cancel (0) resetSystemNow (1) *SetDefaults 710.3.3. 10.2 (*UnitControl 2) Applicable to all products. Sets unit configuration to Defaults values after the next reset.
Appendix C MIB Parameter (Location in Parenthesis) C-35 Description Values/Range *EraseEventLog 710.3.3. 10.10.3 (*EventLog 3) Applicable to all products. Deletes all entries from the Event Log file. Integer cancel (0) erase (1) *SaveCurrentConfigurationAs OperatorDefaults 710.3.3. 10.12 (*UnitControl 12) Applicable to all products. Saves the current configuration as Operator Defaults. Integer cancel (0) saveAsDefaults (1) *ExitMonitorOrTelnet 710.3.3. 10.
BreezeACCESS Version 4.3 System Manual C-36 IP Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *IpParams 710.3.3. 11 (brzAccessMib 11) *UnitIpAddress 710.3.3. 11.1 (*IpParams 1) Applicable to all products. IP address of the unit. IP address *SubNetMask 710.3.3. 11.2 (*IpParams 2) Applicable to all products. Subnet mask of the unit. IP address *DefaultGWAddress 710.3.3. 11.3 (*IpParams 3) Applicable to all products. Default gateway IP address of the unit.
Appendix C MIB Parameter (Location in Parenthesis) C-37 Description Values/Range *UnitType 710.3.3. 13.7 (*SysInfo 7) Applicable to all products. Read-only: Unit type. DisplayString (SIZE(0..32)) *AssociatedAU 710.3.3. 13.8 (*SysInfo 8) Applicable to SU only. Read-only: Associated AU MAC address. MAC address *NumOfAssociationsSinceLastReset 710.3.3. 13.9 (*SysInfo 9) Applicable to AU and SU. Read-only: The number of associations since last reset, including duplicate associations (reassociations).
BreezeACCESS Version 4.3 System Manual C-38 Alarms Parameters MIB Parameter (Location in Parenthesis) Description Values/Range *Alarms 710.3.3. 20 (brzAccessMib 20) Alarms parameters *GpsAlarms 710.3.3. 20.1 (*Alarms 1) Applicable to GU only. GPS Alarms parameters. *AlarmInTable 710.3.3. 20.1.1 (*GpsAlarms 1) Applicable to GU only. Names and status of Alarms-In. Not accessible. *AlarmInTableEntry 710.3.3. 20.1.1.1 (*AlarmInTable 1) Applicable to GU only. An Alarms In table entry. Not accessible.
Appendix C C-39 brzPhoneMIB (applicable to SU with voice only) breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.710 {(iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) breezecom(710)} breezecomPrvRev {breezecom 3} OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3 brzPhoneMib {breezecomPrvRev 4 } OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3.4 Note: * is used instead of the phon prefix Dialing Parameters MIB Parameter (Location in Parenthesis) Description Values *DialingParams 710.3.4.
BreezeACCESS Version 4.3 System Manual C-40 MIB Parameter (Location in Parenthesis) Description Values *InformTransferCap 710.3.4.1.14 (*DialingParams 14) Defines the value of the information transfer capability in the SETUP message. Integer speech (0) unrestricted (1) restricted (2) audio (3) unrestrictedTones (4) video (5) na (255) *DTMFRelay 710.3.4.1.15 (*DialingParams 15) Disable/enable DTMF Relay. 0 ñ Disable. DTMF is transferred inband. 1 ñ Enable. In-band DTMF is filtered.
Appendix C MIB Parameter (Location in Parenthesis) C-41 Description Values *AlternateGkOption 710.3.4.1.24 (*DialingParams 24) Setting the Alternate Gatekeeper feature. EnableManualDiscovery: the Alternate Gatekeeper IP address is specified by the Alternate Gatekeeper IP Address parameter. EnableAutomaticDiscovery: the Alternate Gatekeeper IP address is received from the Primary GK. Integer disable (0) enableManualDiscovery (1) enableAutomaticDiscovery (2) na (255) *AlternateGkIPAddress 710.3.4.1.
BreezeACCESS Version 4.3 System Manual C-42 Voice Parameters MIB Parameter (Location in Parenthesis) Description Values *VoiceParams 710.3.4.2 (brzPhonMib 2) *VoiceVolume 710.3.4.2.1 (*VoiceParams 1) Gain of signal to earphone. Integer 0-20 (-dB) na (255) *EchoCancellation 710.3.4.2.3 (*VoiceParams 3) Enables or disables the echo cancellation feature. Integer disable (0) enable (1) na (255) *VoiceCodec 710.3.4.2.4 (*VoiceParams 4) The relative priority of voice codecs. DisplayString (SIZE (0..
Appendix C C-43 Telephony Signals MIB Parameter (Location in Parenthesis) Description Values *TelephonySignals 710.3.4.3 (brzPhonMib 3) *TelephonyCountryStandard 710.3.4.3.1 (*TelephonySignals 1) The country standard for call progress tones, ringer and timeouts. *TonesTable 710.3.4.3.2 (*TelephonySignals 2) A table of parameters of the tones. If the *TelephonyCountryStandard is set to proprietary, the tones parameters may be configured (read/write).
BreezeACCESS Version 4.3 System Manual C-44 MIB Parameter (Location in Parenthesis) Description Values *MinimumFlashDetectTimeOut 710.3.4.3.3.1 (*TimeOuts 1) The minimum on-hook time for identifying it as a Hook Flash. Integer 0-2,000 (milliseconds) *MaximumFlashDetectTimeOut 710.3.4.3.3.2 (*TimeOuts 2) The maximum on-hook time for identifying it as a Hook Flash. Integer 0-2,000 (milliseconds) *DisconnectTimeOut 710.3.4.3.3.
Appendix C MIB Parameter (Location in Parenthesis) C-45 Description Values *TrapToggle 710.3.3.14.5 (*Traps 5) An On/Off toggle status, indicating a change in status from off to on or vice versa. Integer on (1) off (2) *LastAUMacAddress 710.3.3.14.6 (*Traps 6) Applicable to SU only. The MAC address of the last AU with which the SU was associated. MAC address *TrapLog 710.3.3.14.7 (*Traps 7) Login or logout to the monitor program via the Monitor port or Telnet.
BreezeACCESS Version 4.3 System Manual C-46 Traps Trap (Number) Description Variables *SUassociatedAUTRAP(2) An AU trap indicating a new association with an SU. *TrapSUMacAddr *AUdisassociatedTRAP(3) An AU trap indicating that an SU has been disassociated from the AU. The AU decides that an SU has been disassociated from it and remove it from the ADB after receiving from another AU a SNAP frame with the SU MAC address.
Appendix C C-47 Trap (Number) Description Variables *NoAssociationsOnTRAP (201) An IF-based AU alarm. Alarm was set on: The AU was reset 3 consecutive times as a result of no association with any SU, and before that the AU was associated with at least Minimum Number Of SUs. *TrapAUAlarmsSeverity *NoAssociationsOffTRAP (202) Alarm was set off: At least one SU became associated with the AU. The alarm will be set off also after activating Clear All Alarms or after disabling the AU Alarms Option.
BreezeACCESS Version 4.3 System Manual C-48 Trap (Number) Description Variables *HighRetransmissionsRateOnTRAP (209) Alarm was set on: Minor Severity Alarm: a. The Retransmissions Current Rate exceeds the Retransmissions Minor Alarm Threshold, and is higher than the Retransmissions Average Rate by at least Retransmissions Minor Alarm Minimum Delta. b.
Appendix C C-49 Trap (Number) Description Variables *HighCRCErrorRateOnTRAP (213) Alarm was set on: Minor Severity Alarm: a. The CRC Error Current Rate exceeds the CRC Error Minor Alarm Threshold, and is higher than the CRC Error Average Rate by at least CRC Error Minor Alarm Minimum Delta. b. The CRC Error Current Rate has dropped below the CRC Error Major Alarm Threshold but is still higher than the CRC Error Minor Alarm Threshold.
C-50 Manual Revision: 4.0 BreezeACCESS Version 4.
Appendix D: RSSI to dBm Conversion Table RSSI 71 72 74 75 77 78 81 82 83 84 85 86 88 89 90 91 92 93 94 96 97 98 99 100 101 102 103 104 105 106 107 108 110 111 112 113 dBM -100 -99 -98 -97 -96 -95 -94 -93 -92 -91 -90 -89 -88 -87 -86 -85 -84 -83 -82 -81 -80 -79 -78 -77 -76 -75 -74 -73 -72 -71 -70 -69 -68 -67 -66 -65 RSSI 114 115 116 118 119 120 121 122 123 125 126 127 128 129 130 131 133 134 135 136 137 138 139 141 142 143 144 145 146 148 149 150 151 152 153 dBM -64 -63 -62 -61 -60 -59 -58 -57 -56 -55 -54
D-2 Manual Revision: 4.0 BreezeACCESS Version 4.
Appendix E: Parameters List Unit Control Parameters Parameter Unit Range Default Run-Time Updated Change Unit Name All Up to 32 printable ASCII Empty String characters Yes Change Readonly Password All Up to 8 printable ASCII characters public Yes – For access from Monitor or Telnet only Change Installer Password All Up to 8 printable ASCII characters user Yes – For access from Monitor or Telnet only Change Administrator Password All Up to 8 printable ASCII characters private Yes – For
BreezeACCESS Version 4.
Appendix E E-3 Range Default RunTime Updated Parameter Unit Duplicate Frames Minor Alarm Minimum Delta IF-based AU 0 – 100 (%) 5 (%) Yes Duplicate Frames Minor Alarm Threshold IF-based AU 1 – 100 (%) 5 (%) Yes Duplicate Frames Major alarm Threshold IF-based AU 1 – 100 (%) 15 (%) Yes SU Rx Power Decrease Threshold IF-based AU 1 – 99 (dBm) 15 (dBm) Yes AU Rx Power Decrease Threshold IF-based AU 1 – 99 (dBm) 15 (dBm) Yes Minimum Number Of SUs IF-based AU 1 – 254 (SUs) 5 (SUs)
BreezeACCESS Version 4.3 System Manual E-4 Air Interface Parameters Parameter Unit Range Default Run-Time Updated ESSID AU, SU Up to 31 printable ASCII characters ESSID1 No Operator ESSID Option AU Disable, Enable Enable No Operator ESSID AU Up to 31 printable ASCII characters ESSID1 No Hopping Band (5.7 GHz Products) AU, SU ISM US FCC, ISM International, Flexible Hopping definition ISM US FCC No Frequency Offset (5.
Appendix E E-5 Parameter Unit Range Default Run-Time Updated Hopping Sync AU Idle, Master, Slave Idle No Best AU Support SU Disable, Enable Disable No Number of Scanning Attempts SU 1 – 255 20 Yes Preferred AU MAC SU Address MAC Address 00-00-00-00-00-00 (no Yes preferred AU) Transmit Power Control 0–7 7 Yes Receive AU, SU Attenuation Control 0, 10dB, 25dB 0 No Maximum Data Rate AU, SU 1, 2 and 3Mbps 3Mbps No AU Transmission Rate Control SU Disable, Enable No Acknowl
BreezeACCESS Version 4.
Appendix E E-7 Network Management Parameters Parameter Unit Range Default RunTime Updated Access To Network Management AU, SU From Wlan Only, From Ethernet Only, From Both Ethernet & Wlan From Both Ethernet & Wlan No Network Management Filtering All Disable, Activate Management IP Filter On Ethernet Port, Activate Management IP Filter On Wlan Port (not available in GU), Activate Management IP Filter On Both Ethernet & Wlan Ports (not available in GU), Disable No Set Network Management IP A
BreezeACCESS Version 4.
Appendix E E-9 Bridge Parameters Parameter Unit VLAN ID-Data SU VLAN ID – Management Range 1 – 4094 Default Run-Time Updated 1 No AU, GU, 1 – 4094, 65535 SU without voice 65535 (no VLAN) No VLAN ID – Voice & Management SU with voice 1 – 4094, 65535 65535 (no VLAN) No VLAN Link Type AU, SU Hybrid Link, Trunk Link, Access Link (only in SU) Hybrid Link No Voice Priority Tag Option SU with voice Disable, Enable Disable No VLAN Forwarding Support AU, SU Disable, Enable Disable
BreezeACCESS Version 4.
Appendix E E-11 Performance Parameters Parameter Unit Range Default Run-Time Updated RTS Threshold AU, SU 20 – 1600 bytes AU: 1600 SU: 60 No Number of Retransmissions AU, SU 1 – 100 1 No Number of Retransmissions to Decrease Rate AU, SU 0 – 10 0 No Number of Dwells to Retransmit AU, SU 0–9 2 No Minimum Contention Window AU, SU 7 - 255 31 No Carrier Sense Level AU, SU -100 to -40 (dBm) 5.2 GHz: -90 (dBm) 5.
BreezeACCESS Version 4.3 System Manual E-12 Service Parameters Parameter Unit Range Default RunTime Updated User Filtering Option SU Disable, IP Only, User Defined Addresses Only, PPPoE Protocol Only Disable Yes Set User Filter Address SU IP address (8 entries) 0.0.0.0 (all 8 entries) Yes Set User Filter Mask SU IP address (8 entries) 255.255.255.
Appendix E E-13 RADIUS Parameters Parameter Unit Range Default RunTime Updated User Name SU Up to 64 printable ASCII characters The units’ MAC Address No User Password SU Up to 64 printable ASCII characters RadiusPassword1 No Shared Secret SU Up to 20 characters RadiusSecret1234 No Authentication Option SU Disable, enable Disable No RADIUS Server SU Authentication IP Address IP Address 0.0.0.
BreezeACCESS Version 4.
Appendix E E-15 Dialing Parameters Parameter Unit Range Default RunTime Updated Pulse Dialing SU with voice Disable, Enable Enable No Gatekeeper Option SU with voice Disable, Enable Disable No Gatekeeper / Gateway IP Address SU with voice IP address 0.0.0.0 No Alternate Gatekeeper Option SU with voice Disable, Enable Disable No Alternate Gatekeeper IP Address SU with voice IP address 0.0.0.
BreezeACCESS Version 4.3 System Manual E-16 Parameter International Prefix Unit SU with voice Range Default RunTime Updated One phone key-pad digit 0 (0-9, *, #, A, B, C, D) and X (no prefix).
Appendix E E-17 Telephony Signals Parameter Unit Range Default RunTime Updated Telephony SU with Country Standard voice Proprietary, Germany, Sweden, France, United Kingdom, Belgium, USA, Chile USA No Frequency 1 SU with voice 0 – 3000Hz Dial Tone: 350 No Ring Back: 440 Busy: 480 Congestion: 480 Error: 480 High Level Error: 20 Frequency 1 SU with voice 0 – 3000Hz Dial Tone: 350 No Ring Back: 440 Busy: 480 Congestion: 480 Error: 480 High Level Error: 0 Ring Frequency: 20 Level 1 SU with
BreezeACCESS Version 4.
Appendix E E-19 Hopping Parameters Parameter Unit Range Default RunTime Updated Number of Hopping Frequencies GU 2-151 No Automatic Recovery Option GU Disable, Enable Enable Yes Automatic Recovery Interval GU 5 – 1440 (minutes) 15 (minutes) Yes ACSE Option AU and GU Disable, Enable Disable No Dwell Time AU and GU 32, 64, 128 128 No Alarm Parameters Parameter Unit Range Default RunTime Updated Alarm In Names GU Up to 31 printable ASCII Alarm In 1 characters through Alar
E-20 Manual Revision: 4.0 BreezeACCESS Version 4.
Index 1-1 Index A Access Link Parameter Access to DHCP Parameter Access to Network Management Parameter Access Units AU-A/E-NI Accounting Interval Accounting Option Accounting Parameters Menu Acknowledge Delay Limit Parameter ACSE Number Of Retransmissions For Data Parameter ACSE Number Of Retransmissions For Voice Parameter ACSE Option ACSE Option Parameter ACSE Parameters Parameter Add Forwarding VLAN ID Parameter Add Frequencies Parameter Add Relaying VLAN ID Parameter Advanced Configuration Menu Air I
1-2 Packing List AU-NI Installation Authentication Algorithm Parameter Authentication Option Authentication Parameters Menu Automatic Alarms Out Definition Menu Automatic Prefix Parameter Automatic Recovery Interval Automatic Recovery Option B Bad fragments received Parameter Base Station Equipment Basic Configuration Menu Battery Polarity Parameter Best AU Parameters in SU Parameter Best AU Selection Parameters Best AU Support Parameter BreezeACCESS Introduction BreezeCONFIG BreezeMANAGE Bridge Aging Time
Index 1-3 Call Aging Time Parameter Called Party Release Timeout Parameter Carrier Sense Level Parameter Carrier to Interference Difference Level Change Password Parameter Change Unit Name Parameter CIR - AU to SU Parameter CIR - SU to AU Parameter Commissioning AL IN and AL OUT Connectors Aligning SU-A/E Antenna GU-A-BS Maximum Data Rate Compression Efficiency Parameter Configuring Basic Parameters GU-A-BS units RSSI and Maximum Data Rate Congestion Tone Parameter Connectors AL IN and AL OUT Console Spee
1-4 Disconnect Timeout Parameter Display Association Info Parameter Display Bridging & Association Info Display Bridging & Association Info Parameter Display CIR/MIR Info Parameter Display Counters Parameter Display Event Log Parameter Dropped Frames Rate Parameters DTMF Relay Parameter Duplicate frames discarded Parameter Duplicate Frames Rate Parameters Duration Duration Parameter Dwell Time Parameter BreezeACCESS Version 4.3 Index ...Book 4, 2-106 ...Book 4, 2-21 ...Book 4, 2-20 ...Book 4, 2-20 ...
Index 1-5 G723 Frames Per Packet Parameter G729 Frames Per Packet Parameter Gatekeeper Option Parameter GateKeeper/GateWay IP Address Parameter General RADIUS Parameters Menu GPS and Alarms System Installation GPS and Alarms system Graceful Degradation Limit Parameter GU-A-BS Configuring Installation Packing List GU-BS AL IN and AL OUT Connectors H H323 Terminal ID Parameter High Level Error Tone Parameter Hopping Parameters Hopping Parameters Menu Hopping Shift Hopping Sync Hybrid Link Parameter ..
1-6 L LAN to Wireless Link Bridging Mode Parameter Learning Period Parameter Level 1 Parameter Level 2 Parameter Locating Units AU-RA AU-RE IF Cable Indoor Equipment SU-RA SU-RE Log Out Timer Parameter M MAC Address Black List MAC Address Database Main Menu Management Systems BreezeCONFIG BreezeMANAGE Manual Sequence Definition Max.
Index 1-7 IP Parameters Main Network Management Parameters Performance Parameters Security Parameters Service Parameters Show Advanced Parameters Show Alarm Parameters Show All Parameters Show Basic Parameters Show Unit Status Site Survey Telephony Signals Unit Control Voice Parameters Micro-Cell Access Unit Min.
1-8 Outdoor Units Bottom Panel Installation Pole Mounting Overlap Sending P Packing Lists AU-A/E-BS AU-A/E-NI BS-PS BS-PS-AC BS-SH BS-SH-AC GU-A-BS SU-A/E Per Hop Statistics Per Trap Control BreezeACCESS Version 4.3 Index ..Book 2, 1-7 ..Book 2, 1-7 ..Book 2, 1-9 ...
Index 1-9 Ring Frequency Parameter Ring-Back Tone Parameter Ringer Frequency Parameter RSSI Display Option RSSI Memory Factor RTS Threshold Parameter ..Book 4, 2-105 ..Book 4, 2-104 ..Book 4, 2-105 ..Book 4, 2-23 ..Book 4, 2-59 ..
1-10 Site Survey Parameters SNMP Traps Community Parameter SNMP Traps IP Destination SNMP Traps IP Destination Parameter SNMP Traps Parameter Spanning Factor Specifications AU-A/E-NI Configuration and Managemen Data Communication Environmental GU-RA GPS Radio GU-RA to BS-GU Communication IF Indoor Outdoor Communication Modular Base Station Equipmen Physical Radio and Modem Standards Compliance, General SU-A/E Telephony Voice/Fax Start Sending Parameter Statistics Per Hop Traffic Voice Stop Sending Paramete
Index 1-11 Test Cycle Parameter Timeouts Parameter ToS Precedence Threshold Parameter ToS Priority Parameter ToS Priority Parameters Total received data frames Parameter Total received frames from wireless Parameter Total received frames via Ethernet Parameter Total retransmitted frames Parameter Total submitted frames (bridge) Parameter Total transmitted frames to wireless Parameter Total Tx errors Parameter Traffic Statistics Transmit Power Control Algorithm Transmit Power Control Parameter Transmitted
1-12 BreezeACCESS Version 4.
