User Manual
Table Of Contents
- Chapter 1 - System Description
- 1.1 Introducing BreezeACCESS VL
- 1.2 Base Station Equipment
- 1.3 Subscriber Unit
- 1.4 BreezeACCESS VL B&B (4.9 GHz only)
- 1.5 Networking Equipment
- 1.6 Management Systems
- 1.7 Specifications
- 1.7.1 Radio
- 1.7.2 Data Communication
- 1.7.3 Configuration and Management
- 1.7.4 Standards Compliance, General
- 1.7.5 Physical and Electrical
- 1.7.6 Environmental
- Chapter 2 - Installation
- 2.1 Installation Requirements
- 2.2 Equipment Positioning Guidelines
- 2.3 Installing the Outdoor Unit
- 2.4 Installing the Universal IDU Indoor Unit
- 2.5 Installing the SU-I
- 2.6 Installing the Modular Base Station Equipment
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- 4.1 Working with the Monitor Program
- 4.2 Menus and Parameters
- 4.2.1 Main Menu
- 4.2.2 Info Screens Menu
- 4.2.3 Unit Control Menu
- 4.2.3.1 Reset Unit
- 4.2.3.2 Default Settings
- 4.2.3.3 Change Unit Name
- 4.2.3.4 Change Password
- 4.2.3.5 Flash Memory Control
- 4.2.3.6 Log Out Timer
- 4.2.3.7 Ethernet Negotiation Mode
- 4.2.3.8 Change System Location
- 4.2.3.9 Event Log Menu
- 4.2.3.10 Feature Upgrade
- 4.2.3.11 SW Version Download
- 4.2.3.12 Configuration File Upload/Download
- 4.2.4 Basic Configuration Menu
- 4.2.5 Site Survey Menu
- 4.2.6 Advanced Configuration Menu
- 4.2.6.1 IP Parameters
- 4.2.6.2 Air Interface Parameters
- 4.2.6.2.1 Country Code and Sub-Bands
- 4.2.6.2.2 ESSID Parameters
- 4.2.6.2.3 Frequency Definition Parameters
- 4.2.6.2.4 Frequency Definition Submenu in AU
- 4.2.6.2.5 Frequency Definition Submenu in SU
- 4.2.6.2.6 Best AU Parameters (SU)
- 4.2.6.2.7 Scanning Mode (SU only)
- 4.2.6.2.8 Power Control Parameters
- 4.2.6.2.9 Antenna Gain
- 4.2.6.2.10 Cell Distance Parameters (AU only)
- 4.2.6.2.11 Arbitration Inter-Frame Spacing (AIFS)
- 4.2.6.2.12 Maximum Number of Associations (AU only)
- 4.2.6.2.13 Wireless Link Trap Threshold (AU only)
- 4.2.6.2.14 Spectrum Analysis
- 4.2.6.2.14.1 Spectrum Analysis Channel Scan Period
- 4.2.6.2.14.2 Spectrum Analysis Scan Cycles
- 4.2.6.2.14.3 Automatic Channel Selection (AU only)
- 4.2.6.2.14.4 Spectrum Analysis Activation
- 4.2.6.2.14.5 Reset Spectrum Analysis Information
- 4.2.6.2.14.6 Spectrum Analysis Information Display
- 4.2.6.2.14.7 Spectrum Analysis Information Display - Continuous
- 4.2.6.2.14.8 Show Spectrum analysis Parameters & Data
- 4.2.6.2.15 Lost Beacons Transmission Watchdog Threshold (AU only)
- 4.2.6.2.16 Disassociate (AU only)
- 4.2.6.2.17 Noise Immunity Control
- 4.2.6.2.18 Noise Floor Calculation Parameters
- 4.2.6.3 Network Management Parameters
- 4.2.6.3.1 Access to Network Management
- 4.2.6.3.2 Network Management Filtering
- 4.2.6.3.3 Set Network Management IP Address
- 4.2.6.3.4 Delete a Network Management IP Address
- 4.2.6.3.5 Delete All Network Management IP Addresses
- 4.2.6.3.6 Set/Change Network Management IP Address Ranges
- 4.2.6.3.7 SNMP Traps (AU Only)
- 4.2.6.3.8 Wi2 IP Address (SU Only)
- 4.2.6.4 Bridge Parameters
- 4.2.6.4.1 VLAN Support
- 4.2.6.4.1.1 VLAN ID-Data (SU only)
- 4.2.6.4.1.2 VLAN ID-Management
- 4.2.6.4.1.3 VLAN Link Type
- 4.2.6.4.1.4 VLAN Forwarding (AU and SU)
- 4.2.6.4.1.5 VLAN Relaying (AU only)
- 4.2.6.4.1.6 Service Provider VLAN ID (SU only)
- 4.2.6.4.1.7 VLAN Traffic Priority
- 4.2.6.4.1.8 VLAN QinQ Protocol Ethertype
- 4.2.6.4.1.9 Show VLAN Parameters
- 4.2.6.4.2 Ethernet Broadcast Filtering (SU only)
- 4.2.6.4.3 Ethernet Broadcast/Multicast Limiter
- 4.2.6.4.4 Bridge Aging Time
- 4.2.6.4.5 Broadcast/Multicast Relaying (AU only)
- 4.2.6.4.6 Unicast Relaying (AU only)
- 4.2.6.4.7 MAC Address List (AU only)
- 4.2.6.4.8 Roaming Option (SU only)
- 4.2.6.4.9 Ports Control (SU only)
- 4.2.6.4.10 Show Bridge Parameters
- 4.2.6.4.1 VLAN Support
- 4.2.6.5 Performance Parameters
- 4.2.6.5.1 RTS Threshold
- 4.2.6.5.2 Minimum Contention Window
- 4.2.6.5.3 Maximum Contention Window
- 4.2.6.5.4 Multicast Modulation Level (AU only)
- 4.2.6.5.5 Maximum Modulation Level
- 4.2.6.5.6 Average SNR Memory Factor
- 4.2.6.5.7 Number of HW Retries
- 4.2.6.5.8 Burst Mode
- 4.2.6.5.9 Adaptive Modulation Algorithm (Multi Rate)
- 4.2.6.5.10 Concatenation Parameters
- 4.2.6.6 Service Parameters
- 4.2.6.6.1 User Filtering Parameters (SU only)
- 4.2.6.6.2 MIR and CIR Parameters
- 4.2.6.6.2.1 MIR: Downlink (SU only)
- 4.2.6.6.2.2 MIR: Uplink (SU only)
- 4.2.6.6.2.3 CIR: Downlink (SU only)
- 4.2.6.6.2.4 CIR: Uplink (SU only)
- 4.2.6.6.2.5 Maximum Burst Duration (SU and AU)
- 4.2.6.6.2.6 Maximum Delay (SU only)
- 4.2.6.6.2.7 Graceful Degradation Limit (AU only)
- 4.2.6.6.2.8 MIR Only Option (AU only)
- 4.2.6.6.2.9 MIR Threshold Percent (AU only)
- 4.2.6.6.2.10 Show MIR/CIR Parameters
- 4.2.6.6.3 Traffic Prioritization
- 4.2.6.6.3.1 VLAN Priority Threshold
- 4.2.6.6.3.2 ToS Prioritization
- 4.2.6.6.3.3 UDP/TCP Port Ranges Traffic Prioritization
- 4.2.6.6.3.4 Low Priority Traffic Minimum Percent
- 4.2.6.6.3.5 Wireless Link Prioritization Parameters (AU)
- 4.2.6.6.3.5.1 Wireless Link Prioritization Option
- 4.2.6.6.3.5.2 Low Priority AIFS
- 4.2.6.6.3.5.3 Number of HW Retries for High Priority Traffic
- 4.2.6.6.3.5.4 Number of HW Retries for Low Priority Traffic
- 4.2.6.6.3.5.5 AU Burst Duration for High Priority Traffic
- 4.2.6.6.3.5.6 AU Burst Duration for Low Priority Traffic
- 4.2.6.6.3.5.7 SU Burst Duration for High Priority Traffic
- 4.2.6.6.3.5.8 SU Burst Duration for Low Priority Traffic
- 4.2.6.6.4 DRAP Parameters (AU only)
- 4.2.6.6.5 Show Service Parameters
- 4.2.6.7 Security Parameters
- 4.2.6.8 Country Code Parameters
Chapter 1 - System Description
BreezeACCESS VL System Manual
4
1.2 Base St a t ion Equipment
The Access Units, installed at the Base Station site, provide all the functionality
necessary to communicate with the Subscriber Units and to connect to the
backbone of the Service Provider.
There are 2 lines of Access Units with different architectures:
Modular Base Station Equipment
Standalone “Micro-Cell” Access Unit
1.2.1 Modular Base St ation Equipme nt
The Base Station Equipment is based on the BS-SH 3U chassis, which is suitable
for installation in 19-inch racks. The chassis contains one or two Power Supply
modules and has 8 slots that can accommodate BS-AU Network Interface
modules. These slots can also
accommodate various combinations of
other modules, including Network
Interface (BS-AU) modules for Access
Units operating in any of the bands
supported by BreezeACCESS equipment
using GFSK modulation, including BreezeACCESS II, BreezeACCESS MMDS,
BreezeACCESS XL and BreezeACCESS V. It can also accommodate a BS-GU GPS
and Alarms module to support GPS-based synchronization of BreezeACCESS
systems using Frequency Hopping radios.
Two different types of power supply modules are available for the BreezeACCESS
VL modules: The BS-PS-DC that is powered from a -48 VDC power source, and
the BS-PS-AC, powered from the 110/220 VAC mains. The optional use of two
power supply modules ensures fail-safe operation through power supply
redundancy. When the same chassis is used also for Access Unit modules
belonging to other BreezeACCESS families using GFSK modulation, then one
BS-PS power supply (AC or DC) should be used to provide power to the
BreezeACCESS VL Access Units, and a different power supply module, suitable
for GFSK equipment, is required for powering the BreezeACCESS GFSK Access
Units.
Each BS-AU module and its outdoor radio unit (AU-ODU) comprise an AU-E-BS
Access Unit that together with an external antenna serves a single sector. There
are two types of Access Units, differing in the maximum number of Subscriber
Units that they can serve: