User Manual
Table Of Contents
- Chapter 1 - System Description
- 1.1 Introducing BreezeACCESS VL
- 1.2 Base Station Equipment
- 1.3 Subscriber Unit
- 1.4 BreezeACCESS VL B&B (4.9 GHz only)
- 1.5 Networking Equipment
- 1.6 Management Systems
- 1.7 Specifications
- 1.7.1 Radio
- 1.7.2 Data Communication
- 1.7.3 Configuration and Management
- 1.7.4 Standards Compliance, General
- 1.7.5 Physical and Electrical
- 1.7.6 Environmental
- Chapter 2 - Installation
- 2.1 Installation Requirements
- 2.2 Equipment Positioning Guidelines
- 2.3 Installing the Outdoor Unit
- 2.4 Installing the Universal IDU Indoor Unit
- 2.5 Installing the SU-I
- 2.6 Installing the Modular Base Station Equipment
- Chapter 3 - Commissioning
- Chapter 4 - Operation and Administration
- 4.1 Working with the Monitor Program
- 4.2 Menus and Parameters
- 4.2.1 Main Menu
- 4.2.2 Info Screens Menu
- 4.2.3 Unit Control Menu
- 4.2.3.1 Reset Unit
- 4.2.3.2 Default Settings
- 4.2.3.3 Change Unit Name
- 4.2.3.4 Change Password
- 4.2.3.5 Flash Memory Control
- 4.2.3.6 Log Out Timer
- 4.2.3.7 Ethernet Negotiation Mode
- 4.2.3.8 Change System Location
- 4.2.3.9 Event Log Menu
- 4.2.3.10 Feature Upgrade
- 4.2.3.11 SW Version Download
- 4.2.3.12 Configuration File Upload/Download
- 4.2.4 Basic Configuration Menu
- 4.2.5 Site Survey Menu
- 4.2.6 Advanced Configuration Menu
- 4.2.6.1 IP Parameters
- 4.2.6.2 Air Interface Parameters
- 4.2.6.2.1 Country Code and Sub-Bands
- 4.2.6.2.2 ESSID Parameters
- 4.2.6.2.3 Frequency Definition Parameters
- 4.2.6.2.4 Frequency Definition Submenu in AU
- 4.2.6.2.5 Frequency Definition Submenu in SU
- 4.2.6.2.6 Best AU Parameters (SU)
- 4.2.6.2.7 Scanning Mode (SU only)
- 4.2.6.2.8 Power Control Parameters
- 4.2.6.2.9 Antenna Gain
- 4.2.6.2.10 Cell Distance Parameters (AU only)
- 4.2.6.2.11 Arbitration Inter-Frame Spacing (AIFS)
- 4.2.6.2.12 Maximum Number of Associations (AU only)
- 4.2.6.2.13 Wireless Link Trap Threshold (AU only)
- 4.2.6.2.14 Spectrum Analysis
- 4.2.6.2.14.1 Spectrum Analysis Channel Scan Period
- 4.2.6.2.14.2 Spectrum Analysis Scan Cycles
- 4.2.6.2.14.3 Automatic Channel Selection (AU only)
- 4.2.6.2.14.4 Spectrum Analysis Activation
- 4.2.6.2.14.5 Reset Spectrum Analysis Information
- 4.2.6.2.14.6 Spectrum Analysis Information Display
- 4.2.6.2.14.7 Spectrum Analysis Information Display - Continuous
- 4.2.6.2.14.8 Show Spectrum analysis Parameters & Data
- 4.2.6.2.15 Lost Beacons Transmission Watchdog Threshold (AU only)
- 4.2.6.2.16 Disassociate (AU only)
- 4.2.6.2.17 Noise Immunity Control
- 4.2.6.2.18 Noise Floor Calculation Parameters
- 4.2.6.3 Network Management Parameters
- 4.2.6.3.1 Access to Network Management
- 4.2.6.3.2 Network Management Filtering
- 4.2.6.3.3 Set Network Management IP Address
- 4.2.6.3.4 Delete a Network Management IP Address
- 4.2.6.3.5 Delete All Network Management IP Addresses
- 4.2.6.3.6 Set/Change Network Management IP Address Ranges
- 4.2.6.3.7 SNMP Traps (AU Only)
- 4.2.6.3.8 Wi2 IP Address (SU Only)
- 4.2.6.4 Bridge Parameters
- 4.2.6.4.1 VLAN Support
- 4.2.6.4.1.1 VLAN ID-Data (SU only)
- 4.2.6.4.1.2 VLAN ID-Management
- 4.2.6.4.1.3 VLAN Link Type
- 4.2.6.4.1.4 VLAN Forwarding (AU and SU)
- 4.2.6.4.1.5 VLAN Relaying (AU only)
- 4.2.6.4.1.6 Service Provider VLAN ID (SU only)
- 4.2.6.4.1.7 VLAN Traffic Priority
- 4.2.6.4.1.8 VLAN QinQ Protocol Ethertype
- 4.2.6.4.1.9 Show VLAN Parameters
- 4.2.6.4.2 Ethernet Broadcast Filtering (SU only)
- 4.2.6.4.3 Ethernet Broadcast/Multicast Limiter
- 4.2.6.4.4 Bridge Aging Time
- 4.2.6.4.5 Broadcast/Multicast Relaying (AU only)
- 4.2.6.4.6 Unicast Relaying (AU only)
- 4.2.6.4.7 MAC Address List (AU only)
- 4.2.6.4.8 Roaming Option (SU only)
- 4.2.6.4.9 Ports Control (SU only)
- 4.2.6.4.10 Show Bridge Parameters
- 4.2.6.4.1 VLAN Support
- 4.2.6.5 Performance Parameters
- 4.2.6.5.1 RTS Threshold
- 4.2.6.5.2 Minimum Contention Window
- 4.2.6.5.3 Maximum Contention Window
- 4.2.6.5.4 Multicast Modulation Level (AU only)
- 4.2.6.5.5 Maximum Modulation Level
- 4.2.6.5.6 Average SNR Memory Factor
- 4.2.6.5.7 Number of HW Retries
- 4.2.6.5.8 Burst Mode
- 4.2.6.5.9 Adaptive Modulation Algorithm (Multi Rate)
- 4.2.6.5.10 Concatenation Parameters
- 4.2.6.6 Service Parameters
- 4.2.6.6.1 User Filtering Parameters (SU only)
- 4.2.6.6.2 MIR and CIR Parameters
- 4.2.6.6.2.1 MIR: Downlink (SU only)
- 4.2.6.6.2.2 MIR: Uplink (SU only)
- 4.2.6.6.2.3 CIR: Downlink (SU only)
- 4.2.6.6.2.4 CIR: Uplink (SU only)
- 4.2.6.6.2.5 Maximum Burst Duration (SU and AU)
- 4.2.6.6.2.6 Maximum Delay (SU only)
- 4.2.6.6.2.7 Graceful Degradation Limit (AU only)
- 4.2.6.6.2.8 MIR Only Option (AU only)
- 4.2.6.6.2.9 MIR Threshold Percent (AU only)
- 4.2.6.6.2.10 Show MIR/CIR Parameters
- 4.2.6.6.3 Traffic Prioritization
- 4.2.6.6.3.1 VLAN Priority Threshold
- 4.2.6.6.3.2 ToS Prioritization
- 4.2.6.6.3.3 UDP/TCP Port Ranges Traffic Prioritization
- 4.2.6.6.3.4 Low Priority Traffic Minimum Percent
- 4.2.6.6.3.5 Wireless Link Prioritization Parameters (AU)
- 4.2.6.6.3.5.1 Wireless Link Prioritization Option
- 4.2.6.6.3.5.2 Low Priority AIFS
- 4.2.6.6.3.5.3 Number of HW Retries for High Priority Traffic
- 4.2.6.6.3.5.4 Number of HW Retries for Low Priority Traffic
- 4.2.6.6.3.5.5 AU Burst Duration for High Priority Traffic
- 4.2.6.6.3.5.6 AU Burst Duration for Low Priority Traffic
- 4.2.6.6.3.5.7 SU Burst Duration for High Priority Traffic
- 4.2.6.6.3.5.8 SU Burst Duration for Low Priority Traffic
- 4.2.6.6.4 DRAP Parameters (AU only)
- 4.2.6.6.5 Show Service Parameters
- 4.2.6.7 Security Parameters
- 4.2.6.8 Country Code Parameters
Chapter 4 - Operation and Administration
BreezeACCESS VL System Manual
118
Each successful transmit will be included in this average, by using the
modulation level in which the frame was successfully transmitted as the “Last
Successful Modulation Level”.
In order to receive quick and reliable LQI measurements, there should be
sufficient traffic between the SU and the AU. It is recommended to have traffic of
at least 100 packets per second. The traffic can be generated either by an
external utility (FTP session, ping generator, etc.) or by the Ping Test option in the
Site Survey menu with the appropriate settings (see section
4.2.5.2
).
NOTE
If Limited Test is indicated next to the LQI results, it means that the results may not indicate the true
quality, as not all modulation levels from 1 to 8 are available. The limitation may be due to the HW
of the unit (HW Revision A), or the applicable parameters in the country code, or the configurable
Maximum Modulation Level parameter.
Click the Esc key to abort the test.
4.2.5.4 MAC Address Database
4.2.5.4.1 MAC Address Database in AU
The MAC Address Database option in the AU displays information regarding the
Subscriber Units associated with the AU, as well as bridging (forwarding)
information. When DRAP is supported, it enables viewing details on the active
Gateways in the sector. The following options are available:
Display Bridging and Association Info: The Display Bridging and
Association Info option displays a list of all the Subscriber Units and stations
in the AU's Forwarding Database. For stations behind an SU, the SU's MAC
address is also displayed (SU Address).
Each MAC address entry is followed by a description, which may include the
following:
Et (Ethernet): An address learned from the Ethernet port.
Vp (Virtual port): An address of a node behind an associated SU. For
these addresses, learned from the wireless port, the address of the
applicable SU is also displayed (in parenthesis).
St (Static): An associated SU. For these entries, the following details are
also displayed for each SU: Unit Name, SW version, Unit Type, Distance
from the AU, IP Address, Wi2 IP Address as defined in the SU (or 0.0.0.0
for none), ESSID.
X: An SU that is included in the Deny List.