User's Manual

Appendix E - BreezeACCES VL MIB
BreezeACCESS VL System Manual
232
MIB Parameter Description Value/Range
Table. (Replaces
*DFSChannelFrequency to support
a resolution of 0.5 MHz for units with
HW revision C and higher).
*DFSMinimumPulsesToDetect
(*DFSParameters 8)
Applicable to AU/BU. Defines the
minimum number of pulses to detect
radar.
Integer
1 - 100
*DFSChannelReuseParameters
(*DFSParameters 9)
Channel Reuse Parameters
*DFSChannelReuseOption
(*DFSChannelReuseParameters 1)
Applicable to AU/BU.
Enabling/disabling the DFS Channel
Reuse Algorithm.
Integer
disable (1)
enable (2)
na (255)
*DFSRadarActivityAssessmentPeriod
(*DFSChannelReuseParameters 2)
Applicable to AU/BU.
The period in hours for assessment
of radar activity when the Channel
reuse algorithm is enabled.
Integer
1 – 12 hours.
*DFSMaximumNumberOfDetectionsInAs
sessmentPeriod
(*DFSChannelReuseParameters 3)
Applicable to AU/BU. The maximum
number of radar detection in the
original channel during the Radar
Activity Assessment Period that is
required for reaching a decision to
try again the original channel.
Integer
1 – 10 detections.
*CountryCodeLearningBySU
(*FrequencyDefinition 12)
Applicable to AU only. Starting with
4.0 it is nor applicable for
BreezeACCESS and BreezeNET B.
Defines whether the SU should learn
the country code of the AU.
Integer
disable (1)
enable (2)
na (255)
*CurrentAUOperatingFrequencyNew
(*FrequencyDefinition 13)
Applicable to AU/BU. Read-only.
The operating frequency in MHz.
(Replaces
*CurrentAUOperatingFrequency to
support a resolution of 0.5 MHz for
units with HW revision C and
higher).
DisplayString
For 5.8 GHz products with
SW version below 2.0 the
range is 5740 to 5830 MHz
using a 10 MHz resolution.
For units with SW version
2.0 and up the range is as
defined in the selected Sub-
Band.
*AUDefinedFrequencyNew
(*FrequencyDefinition 14)
Applicable to AU/BU. Read-only. For
5.8 GHz products with SW version
below 2.0 this is the frequency in
MHz of the AU/BU after the next
reset.
For units with SW version 2.0 and up
this is the frequency in MHz to use
when the DFS Option is disabled.
(Replaces *AUDefinedFrequency to
support a resolution of 0.5 MHz for
units with HW revision C and
higher).
DisplayString
For 5.8 GHz products with
SW version below 2.0 the
range is 5740 to 5830 MHz
using a 10 MHz resolution.
For units with SW version
2.0 and up the range is as
defined in the selected Sub-
Band.
*AutoSubBandSelect
(*FrequencyDefinition 15)
Auto Sub Band Select parameters.
Applicable to SU/RB with SW
version 4.0 and higher.
*AutoSubBandSelectedFreqSubset
(*AutoSubBandSelect 1)
Applicable to SU/RB with SW
version 4.0 and higher. Apply the
selected subset. After the next reset
the new subset will be used for
scanning.
Integer
setAllSelectedFreqsSubset
(1),
cancel (2)
*AutoSubBandFrequencySubsetTable
(*AutoSubBandSelect 2)
Applicable to SU/RB with SW
version 4.0 and higher. Not
accessible. The Frequency Subset