User Manual
Table Of Contents
- 4Motion System Manual
- About This Manual
- Contents
- Chapter 1 - System Description
- 1.1 About WiMAX
- 1.2 4Motion Solution
- 1.3 The Base Transceiver Station
- 1.4 Element Management Systems
- 1.5 Specifications
- 1.5.1 Modem & Radio
- 1.5.2 Sensitivity (per channel)*
- 1.5.3 ODUs
- 1.5.4 Micro Outdoor BTS
- 1.5.5 AU - ODU Communication (Macro BTS)
- 1.5.6 Data Communication (Ethernet Interfaces)
- 1.5.7 Configuration and Management
- 1.5.8 Standards Compliance, General
- 1.5.9 Environmental
- 1.5.10 Mechanical and Electrical
- 1.5.11 Antennas
- Chapter 2 - Commissioning of the Macro BTS
- 2.1 Initial NPU Configuration
- 2.2 Completing the Site Configuration Using AlvariSTAR
- Chapter 3 - Operation and Administration of the Macro BTS
- 3.1 Using the Command Line Interface
- 3.1.1 Managing the Macro Outdoor BTS
- 3.1.2 Accessing the CLI
- 3.1.3 Command Modes
- 3.1.4 Interpreting the Command Syntax
- 3.1.5 Using the CLI
- 3.1.6 Managing Users and Privileges
- 3.1.7 Managing Secure Shell (SSH) Parameters
- 3.1.8 Managing the Session
- 3.2 Managing Software Upgrade
- 3.1 Using the Command Line Interface
Document History
4Motion xix System Manual
Specifying Service Flow
Configuration Parameters
Section 3.4.12.11.3.3.2
Updated value range for
ulqos-maxsustainedrate,
dlqos-maxsustainedrate, ul-rsrv-rate-min,
dl-rsrv-rate-min.
August 2009
Configuring Airframe MIMO
Parameters
Section 3.9.12.2.7
Updated default value of bcast-msgzone-loc. August 2009
Managing the Policy Framework
(was previously section 4.3.11.17)
Removed August 2009
Managing Handover Negotiation at
SBS
(was previously 4.8.12)
Removed August 2009
Configuring Alarm Threshold
Parameters
Section 3.9.20.1
Updated value range and default for
ul-mednoise and ul-99prcntnoise.
August 2009
Managing Service Interfaces
Section 3.4.12.8
Updated general description.
Removed QinQ Service Interface.
August 2009
Default login ID
Section 3.1
Changed from root to admin, with privilege
level 10.
August 2009
Configuring Service Flows
Section 3.4.12.11.3.3
Only IPv4CS service flows can be configured
in the device.
August 2009
Configuring ACLs
Section 3.4.10
Added details of modified ACL 1. August 2009
Configuring ODU Port Parameters
Section 3.7.2.2
Added warning - do not disable ODU ports August 2009
Configuring Airframe General
Parameters
Section 3.9.12.2.1
auto-diversity and auto-rx-enable are forced
to true (setting to false will be ignored).
August 2009
Configuring Airframe Cyclic Delay
Parameters
Section 3.9.12.2.4
Updated dependencies. The values are set by
internal logic.
August 2009
Configuring Airframe Linear Delay
Parameters
Previously Section 4.8.16.2.5
Updated dependencies. The values are set by
vendor file.
August 2009
Configuring Airframe Mapping
Parameters
Previously Section 4.8.16.2.6
Updated dependencies. The values are set by
internal logic.
August 2009
Topic Description Date Issued