User's Manual
Table Of Contents
- System Manual Book 1: System Description
- Introduction
- System Components
- Specifications
- System Specifications
- Radio and Modem
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication (SU-A/E, AU-E-NI, AU-E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- System Manual Book 2: Installation
- IF-Based Equipment
- Packing Lists
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- IF-Based Equipment
- System Manual Book 3: Commissioning
- System Manual Book 4: Operations and Administration
- Accessing the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Configuration Download/Upload
- System Manual: Appendices
Appendix B
B-33
BreezeACCESS 4.0 System Manual
brzPhoneMIB (applicable to SU
with voice only)
breezecom OBJECT IDENTIFIER =1.3.6.1.4.1.710
{(iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) breezecom(710)}
breezecomPrvRev OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3
{breezecom 3}
brzPhoneMib OBJECT IDENTIFIER = 1.3.6.1.4.1.710.3.4
{breezecomPrvRev 4 }
Note: * is used instead of the phon prefix
Dialing Parameters
MIB Parameter
(Location in Parenthesis)
Description Values
*DialingParams
710.3.4.1
(brzPhonMib 1)
*PulseDialing
710.3.4.1.1
(*DialingParams 1)
Enables/disables automatic pulse
dialing detection.
Integer
disable (0)
enable (1)
na (255)
*GateKeeperOption
710.3.4.1.2
(*DialingParams 2)
Enables/disables communicating
with the Gatekeeper for call
management purposes.
Integer
disable (0)
enable (1)
na (255)
*GkGwIpAddress
710.3.4.1.3
(*DialingParams 3)
IP Address of the Gateway/
Gatekeeper
The parameters must be specified if
the [*GateKeeperOption] is
enabled.
IP address
*MyTelephoneNumber
710.3.4.1.4
(*DialingParams 4)
The telephone number as specified
in the Gateway, if
[*GateKeeperOption] is disabled. If
the [*GateKeeperOption] is enabled
the number is transmitted to the
Gatekeeper.
DisplayString (SIZE (0..10))
Up to 10 characters.
0 means no number
*H323TerminalID
710.3.4.1.5
(*DialingParams 5)
The H323 Terminal ID (name) to be
used for calling the unit if the
feature is enabled.
Applicable only if the
[*GateKeeperOption] is enabled.
DisplayString (SIZE (0..25))
Up to 24 characters.
X=NoID
*IpDialingOption
710.3.4.1.8
(*DialingParams 8)
Enables/disables dialing using IP
addresses.
Integer
disable (0)
enable (1)
na (255)
*IpDialingIndicator
710.3.4.1.9
(*DialingParams 9)
Specifies the prefix used to identify
an IP dialing string.
DisplayString (SIZE (0..15))
Up to three telephone pad digits (0-9, A-
D, *, #).
X means no IP Dialing Indicator
*AutomaticPrefix
710.3.4.1.10
(*DialingParams 10)
Specifies a default prefix (number
of Gateway trunk) to be
automatically inserted before the
dialed number.
DisplayString (SIZE (0..15))
Up to eight telephone pad digits (0-9, A-
D, *, #).
X means no Automatic Prefix.