User's Manual
Table Of Contents
- System Manual Book 1: System Description
- Introduction
- System Components
- Specifications
- System Specifications
- Radio and Modem
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication (SU-A/E, AU-E-NI, AU-E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- System Manual Book 2: Installation
- IF-Based Equipment
- Packing Lists
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- IF-Based Equipment
- System Manual Book 3: Commissioning
- System Manual Book 4: Operations and Administration
- Accessing the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Configuration Download/Upload
- System Manual: Appendices
B-18
BreezeACCESS 4.0 System Manual
Manual Revision: 1.01
*NeighborAuDbm
710.3.3. 6.23.3.1.7
(*NeighborAuEntry 7)
Applicable to SU only. Read-only.
The received signal strength in
dBm of an AU in the Neighbor AU
Table.
Integer
*PreferredAuMacAddress
710.3.3. 6.23.5
(*BestAu 5)
Applicable to SU only. The MAC
address of the preferred AU
(overriding the Best AU selection
process. 00...00 (all zeros in
address) means no preferred AU is
set.
MAC Address
*TransmitLevel
710.3.3. 6.24
(*AirInterface 24)
For future use in SU-I and AU-I.
Sets the level in dBm of the
transmitted power at the antenna
port.
Integer
0-21
na (255)
*ACSEParameters
710.3.3. 6.27
(*AirInterface 27)
Applicable for AU, SU and GU.
ACSE Voice Scheduler
parameters.
*ACSEOption
710.3.3. 6.27.1
(*ACSEParameters 1)
Applicable for AU, SU and GU.
Read-only in the SU. Disable/
enable the ACSE Voice Scheduler
mechanism.
Integer
disable (0)
enable (1)
*ACSEDwellTime
710.3.3. 6.27.2
(*ACSEParameters 2)
Applicable for AU, SU and GU.
Read-only. The dwell time when the
*ACSEOption is enabled. Currently
set to 60 milliseconds.
Integer
60 (mseconds)
na (255)
*ACSEMaximumVoiceSessions
710.3.3. 6.27.3
(*ACSEParameters 3)
Applicable to AU only.
The maximum number of
simultaneous ACSE voice sessions
permitted to guarantee minimum
quality. Applicable only when the
*ACSEOption is enabled.
Integer
0-15
na (255)
*ACSENumberOfDataRetransmissions
710.3.3. 6.27.4
(*ACSEParameters 4)
Applicable to SU and AU.
Maximum times to retransmit an
unacknowledged data packet.
Applicable only when the
*ACSEOption is enabled.
Integer
0-100
*ACSENumberOfVoiceRetransmissions
710.3.3. 6.27.5
(*ACSEParameters 5)
Applicable to SU with voice and
AU. Maximum times to retransmit
an unacknowledged voice packet.
Applicable only when the
*ACSEOption is enabled.
Integer
0-100
*OperatorESSIDOption
710.3.3. 6.28
(*AirInterface 28)
Applicable for AU only. The
Enabling/disabling the use of the
Operator ESSID.
Integer
disable (0)
enable (1)
na (255)
*MaxNumOfAssociations
710.3.3. 6.29
(*AirInterface 29)
Sets the upper limit for the number
of Subscriber Units that can be
associated with the AU.
Integer
0-512
* SiteProprietary
710.3.3. 6.31
(*AirInterface 31)
Site Proprietary parameters.
Applicable only to BreezeACCESS
II SU and AU configured to work in
the special Site Proprietary hopping
standard.
*SPNumOfFreqs
710.3.3. 6.31.1
(* SiteProprietary 1)
Number of frequencies in the
proprietary hopping sets
parameters.
*FirstSetNumOfFreqs
710.3.3. 6.31.1.1
(*SPNumOfFreqs 1)
Read-Only. Number of frequencies
in the first set.
Integer
na (255)
*SecondSetNumOfFreqs
710.3.3. 6.31.1.2
(*SPNumOfFreqs 2)
Read-Only. Number of frequencies
in the second set.
Integer
na (255)
*ThirdSetNumOfFreqs
710.3.3. 6.31.1.3
(*SPNumOfFreqs 3)
Read-Only. Number of frequencies
in the third set.
Integer
na (255)