User's Manual

B-16
BreezeACCESS 4.0 System Manual
Manual Revision: 1.01
*EraseManualSequence
710.3.3. 6.15.9.3
(*ScramblingDefinition 3)
Applicable to SU and AU. Erase the
manually configured sequence.
Integer
cancelOperation (0)
eraseAll (1)
*SpanningFactor
710.3.3. 6.15.9.4
(*ScramblingDefinition 4)
Applicable to AU only. The
Spanning Factor to be used by the
Enhanced Scrambling mechanism.
The Spanning Factor should be
chosen so that the GCD (Greater
Common Divisor) of the Spanning
Factor and the Number of
Frequencies would be 1 (e.g. for 8
frequencies possible values for the
Spanning Factor are 1, 3, 5 and 7).
The SU learns the value of the
Spanning Factor from the AU.
Integer
From 1 to ‘Number of Frequencies’, provided
it meets the GCD requirement.
*ScrambledSeqTable
710.3.3. 6.15.9.5
(*ScramblingDefinition 5)
Applicable to SU and AU only. The
scrambled sequence to be
supported after next reset. Not
accessible.
*ScrambledSeqEntry
710.3.3. 6.15. 9.5.1
(*ScrambledSeqTable 1)
Applicable to SU and AU only. A
Scrambled Sequence Table entry.
Not accessible.
*ScrambledSeqTableIdx
710.3.3. 6.15. 9.5.1.1
(**ScrambledSeqEntry 1)
Applicable to SU and AU only.
Read-only. A Scrambled Sequence
Table entry index.
Integer
*ScrambledSeqFreqIdx
710.3.3. 6.15. 9.5.1.2
(**ScrambledSeqEntry 2)
Applicable to SU and AU only.
Read-only. A Frequency Index in
the Scrambled Sequence Table.
DisplayString (SIZE(10))
*CallAgingTime
710.3.3. 6.16
(*AirInterface 16)
Applicable to AU only. The aging
time for a voice call in the Call Info
database.
Integer
1-50,000 (seconds)
1=No aging
*SecurityParameters
710.3.3. 6.17
(*AirInterface 17)
Security Parameters
*PrivacyOptionImplemented
710.3.3. 6.17.1
(*SecurityParameters 1)
Applicable to SU and AU. Read
Only. Enable/disable the privacy
option. Normally set to active.
Integer
notActive (0)
active (1)
*AuthenticationAlgorithm
710.3.3. 6.17.2
(*SecurityParameters 2)
Applicable to SU and AU only.
Enables/disables the authentication
option.
openSystem: authentication
messages are not encrypted.
sharedKey: Authentication
messages are encrypted.
Integer
openSystem (0)
sharedKey (1)
*DefaultKeyID
710.3.3. 6.17.3
(*SecurityParameters 3)
Applicable to SU and AU only. The
ID of the key to be used for
encryption the authentication
messages.
Integer
1-4
*WEPKey1
710.3.3. 6.17.4
(*SecurityParameters 4)
Applicable to SU and AU only.
Encryption WEP Key#1. Accessible
only with SNMP Write Community.
DisplayString (SIZE(10))
Ten hexadecimal digits
*WEPKey2
710.3.3. 6.17.5
(*SecurityParameters 5)
Applicable to SU and AU only.
Encryption WEP Key#2. Accessible
only with SNMP Write Community.
DisplayString (SIZE(10))
Ten hexadecimal digits
*WEPKey3
710.3.3. 6.17.6
(*SecurityParameters 6)
Applicable to SU and AU only.
Encryption WEP Key#3. Accessible
only with SNMP Write Community.
DisplayString (SIZE(10))
Ten hexadecimal digits
*WEPKey4
710.3.3. 6.17.7
(*SecurityParameters 7)
Applicable to SU and AU only.
Encryption WEP Key#4. Accessible
only with SNMP Write Community.
DisplayString (SIZE(10))
Ten hexadecimal digits.