User's Manual
Table Of Contents
- System Manual Book 1: System Description
- Introduction
- System Components
- Specifications
- System Specifications
- Radio and Modem
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication (SU-A/E, AU-E-NI, AU-E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- System Manual Book 2: Installation
- IF-Based Equipment
- Packing Lists
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- IF-Based Equipment
- System Manual Book 3: Commissioning
- System Manual Book 4: Operations and Administration
- Accessing the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Configuration Download/Upload
- System Manual: Appendices
Appendix B
B-11
BreezeACCESS 4.0 System Manual
Air Interface Parameters
MIB Parameter
(Location in Parenthesis)
Description Values/Range
*AirInterface
710.3.3. 6
(brzAccessMib 6)
*ESSID
710.3.3. 6.1
(*AirInterface 1)
Applicable to SU and AU. The
Extended Service Set ID (ESSID)
used to prevent the merging of
collocated systems. Accessible
only with SNMP Write Community.
DisplayString (SIZE(31))
Up to 31 printable case sensitive ASCII
characters.
*AckDelayLimit
710.3.3. 6.2
(*AirInterface 2)
Applicable to SU and AU. Defines
the maximum time the unit waits for
an Acknowledgment (ACK)
message before retransmission.
Defining a higher range causes the
unit to wait a longer time for ACKs
before retransmission.
Low: Up to 10km
Medium: Up to 20km
High: Greater than 20km.
Integer
Low (0)
Medium (1)
High (2)
na (255)
*FreqOffset
710.3.3. 6.3
(*AirInterface 3)
Applicable to SU and AU in
BreezeACCESS XL family. Not
applicable to units that support only
Flexible Hopping Definition for
setting the hopping frequencies
(e.g. 3.3a band). Not applicable in
Flexible Hopping Definition mode.
Determines the beginning of the
actual hopping band or single
channel frequency relative to the
beginning of the radio band.
Start of hopping band (channel) =
Start of radio band+2 X Frequency
Offset
Integer
na (255)
The valid range of values is dependent on
the bandwidth of the radio and on the
selected Hopping Band.
Max. Frequency Offset = [Overall radio
bandwidth-Hopping Band]/2
*TransmitDiversity
710.3.3. 6.4
(*AirInterface 4)
Applicable to SU-R, SU-I and AU-I
units only.
Enables the selection of the
antenna(s) to be used for
transmission.
Integer
use2Antennasn (0)
antenna1 (1)
antenna2 (2)
na (255)
*HoppingSequence
710.3.3. 6.5
(*AirInterface 5)
Applicable to AU in
BreezeACCESS II family only.
Determines the hopping sequence
to be used. Different AUs in the
same geographical area should use
different Hopping Sequences from
the same Hopping Set.
The valid range is dependant on
the Country Standard.
Integer
Na (255)
Australia: 1-20
Canada: 1-10
Europe ETSI: 1-26
France: 1-11
Israel: 1-11
Japan: 1-4
Korea: 1-4
Netherlands: 1-5
Spain: 1-9
US FCC: 1-26
Mexico: 1-10
International: 1-26
*HoppingSet
710.3.3. 6.6
(*AirInterface 6)
Applicable to AU in
BreezeACCESS II family only.
Determines the hopping set to be
used. All AUs in the same
geographical area should use the
same Hopping Set.
Integer
1-3
na (255)