User's Manual
Table Of Contents
- System Manual Book 1: System Description
- Introduction
- System Components
- Specifications
- System Specifications
- Radio and Modem
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication (SU-A/E, AU-E-NI, AU-E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- System Manual Book 2: Installation
- IF-Based Equipment
- Packing Lists
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- IF-Based Equipment
- System Manual Book 3: Commissioning
- System Manual Book 4: Operations and Administration
- Accessing the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Configuration Download/Upload
- System Manual: Appendices
Menus and Parameters
2-67
BreezeACCESS 4.0 System Manual
" Unrestricted with tones (used by H.323 AudioVisual
terminals for transmission of unrestricted digital information
with tones/announcement)
" Video (not used by H.323 terminals)
The default is Speech.
! Dialing Prefix Parameters – Supports definition of prefix strings
indicating an inter-regional or international call. The algorithm
supports dialing plans where one specific digit is used as the prefix
for inter-regional calls, and two specific digits are used as the prefix
for international calls, where the first one is the same as the
inter-regional call prefix. It can also support dialing plans in which
the inter-regional prefix should be removed at the CPE before the
dialed number is transferred to the system. The dialing plan support
algorithm incorporated into the units operates as follows:
• If the Dialing Prefix Option is disabled the unit will insert the
Automatic Prefix (if defined) before the dialed number.
Otherwise it will be forwarded as dialed.
• If the Dialing Prefix Option is set to Enabled and the first
dialed digit differs from the Inter-Regional Prefix the unit will
insert the Automatic Prefix (if defined) before the dialed
number. Otherwise it will be forwarded as dialed.
• If the Dialing Prefix Option is set to Enable & Block Inter-
Regional Prefix and the first dialed digit differs from the
Inter-Regional Prefix, the unit will insert the Automatic
Prefix (if defined) before the dialed number. If the first dialed
digit is the Inter-Regional Prefix and the second one differs
from the International Prefix (indicating an inter-regional
call), the first digit (the Inter-Regional Prefix) will be removed
before forwarding the dialed number, thus blocking inter-
regional calls at the unit. Otherwise it will be forwarded as
dialed.
" Dialing Prefix Option – Enables or disables the dialing
prefix support capability.
Valid options are: Disable, Enable, Enable & Block Inter-
Regional Prefix.
Default selection is Disable.
" Inter-Regional Prefix – Defines the prefix indicating an
inter-regional call. This is also the first digit in the two digits
string indicating an international call.
Valid values: One phone key-pad digit (0-9, *, #, A, B, C, D)
and X (no prefix).
NOTE:
This information element is encoded according to Figure 4-11/Q.931 and Table 4-6/
Q.931. The SU support only H323 Speech traffic and a change of the default value
is not recommended. A change will be needed only as result of special PSTN switch
requirements.