User's Manual
Table Of Contents
- System Manual Book 1: System Description
- Introduction
- System Components
- Specifications
- System Specifications
- Radio and Modem
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication (SU-A/E, AU-E-NI, AU-E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- System Manual Book 2: Installation
- IF-Based Equipment
- Packing Lists
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- IF-Based Equipment
- System Manual Book 3: Commissioning
- System Manual Book 4: Operations and Administration
- Accessing the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Configuration Download/Upload
- System Manual: Appendices
Menus and Parameters
2-65
BreezeACCESS 4.0 System Manual
! Pulse Dialing – Enables or disables the automatic pulse dialing
detection feature to support telephones with pulse dialing.
The default selection is Enable.
! Gatekeeper Option – If set to Enable, the unit will communicate
with the Gatekeeper to resolve the destination telephone number
into the IP address and to register its own phone number and IP
address with the Gatekeeper.
The default selection is Disable.
! GateKeeper/GateWay IP Address – Specifys the IP address of the
Gateway/Gatekeeper. If the Gatekeeper Option parameter (see
above) is set to Enable, an IP address must be specified.
The default value is 000.000.000.000.
! Alternate Gatekeeper Option - Enables or disables the Alternate
Gatekeeper feature. For the purposes of ensuring system
availability, redundancy, and scalability, the Gatekeeper may
provide the RAS signaling function by utilizing multiple physical or
logical devices, referred to as Alternate Gatekeepers.
If the Alternate Gatekeeper Option set to Automatic Discover, the
Alternate Gatekeeper IP address is received from the Primary GK.
Otherwise, in Manual Discovery mode the Alternate Gatekeeper IP
address is specified by the Alternate Gatekeeper IP Address
parameter (see below).
Valid selections: Disable, Enable (Automatic Discovery), Enable
(Manual Discovery).
Default selection is Disable.
! Alternate Gatekeeper IP Address – Sets the Alternate Gatekeeper
IP address when Alternate Gatekeeper Option parameter (see above)
is set to Manual.
The default value is 000.000.000.000.
! Telephone Number – The telephone number as specified in the
Gateway (if it is required by the specific type of Gateway used).
Valid values: up to 10 digits (0-9).
The default number is 0000....0 (10 zeros).
! H323 Terminal ID – The H323 Terminal ID (Name) to be used for
calling the terminal when the caller uses this feature (e.g.
NetMeeting).
Valid values: up to 24 characters.
The default selection is X (No H323 Terminal ID).
NOTE:
When using a Gateway without a Gatekeeper, this number must be predefined in the
Gateway