User's Manual
Table Of Contents
- System Manual Book 1: System Description
- Introduction
- System Components
- Specifications
- System Specifications
- Radio and Modem
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication (SU-A/E, AU-E-NI, AU-E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- System Manual Book 2: Installation
- IF-Based Equipment
- Packing Lists
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- IF-Based Equipment
- System Manual Book 3: Commissioning
- System Manual Book 4: Operations and Administration
- Accessing the Monitor Program
- Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Configuration Download/Upload
- System Manual: Appendices
Menus and Parameters
2-49
BreezeACCESS 4.0 System Manual
Trunk Link and the VLAN Forwarding option is enabled, a
received data frame with a VLAN ID that is not a member of
the unit’s VLAN Forwarding List will be discarded. The VLAN
Forwarding parameter provides the following options:
# VLAN Forwarding Support – Enables or disables the
VLAN Forwarding feature.
Available selections are Disable and Enable.
The default selection is Disable.
# Add Forwarding VLAN ID – Adds a VLAN ID to the VLAN
Forwarding List. One VLAN ID can be entered each time.
The maximum number of VLAN IDs in the VLAN
Forwarding List is 20.
Valid values are 1 to 4094.
# Remove Forwarding VLAN ID – Removes a VLAN ID from
the VLAN ID Forwarding List.
Valid values are VID values (from 1 to 4094) that are
included in the VLAN Forwarding List.
# Show VLAN ID Forwarding List – Displays the values of
the VLAN IDs that are included in the VLAN Forwarding
List.
" VLAN Relaying (AU only) – Applicable for Trunk link only.
Defines the VLAN ID values that will be included in the VLAN
Relaying List. If the Link Type is defined as Trunk Link and
the VLAN Relaying option is enabled, a received wireless link
relayed frame (a frame received from the wireless link that
should be transmitted back through the wireless link) with a
VLAN ID that is not a member of the unit’s VLAN Relaying
List, will be discarded. If VLAN Forwarding Support is also
enabled, it is necessary to configure all the VLAN IDs in the
Relaying List also in the Forwarding List to enable the
relaying operation.
The VLAN Relaying menu provides the following options:
# VLAN Relaying Support – Enables or disables the VLAN
Relaying feature.
Available selections are Disable and Enable.
The default selection is Disable.
# Add Relaying VLAN ID – Adds a VLAN ID to the VLAN
Relaying List. One VLAN ID can be entered each time.
NOTE:
If the VLAN ID Forwarding List is empty and the VLAN Forwarding Support is
enabled, then all data frames will be discarded.