User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
1-24
BreezeACCESS Version 4.3 Installation
Manual Revision: 3.0
4. Connect the 12-pin round connector to the GPS antenna.
5. Route the cable to the location intended for installation of the BS-GU
module.
Installing the BS-GU module
Inserting the BS-GU Module and Connecting
It to the Antenna
1. Carefully insert the BS-GU module into any of the free suitable slots in the
BS-SH chassis and push firmly until it is securely locked. Close the captive
screws attached to the module.
2. Connect the 9-pin micro D-Type connector of the GPS cable to the
SYNC IN connector (the top-left connector) of the BS-GU module.
Daisy-chaining Two or More BS-GU
Modules
If two or more BS-GU modules are installed in different collocated
BS-SH chassis, use a synchronization cable (supplied separately) to
connect the SYNC OUT connector of the first (Master) module to the
SYNC IN connector of the second module. The SYNC OUT of this second
module may be connected to the SYNC IN of a third module, and so on.
NOTE:
Outdoor units and antennas should be installed ONLY by experienced installation
professionals who are familiar with local building and safety codes and, wherever
applicable, are licensed by the appropriate government regulatory authorities.
Failure to do so may void the BreezeACCESS product warranty and may expose the
end user or the service provider to legal and financial liabilities. Alvarion and its resellers
or distributors are not liable for injury, damage or violation of regulations associated with
the installation of outdoor units or antennas.
NOTE:
When adding the BS-GU to an active base station, it is recommended to start by
reconfiguring the AU previously defined as Master to Slave, then immediately inserting
and configuring the Number of Hopping Frequencies parameter in the BS-GU
module. Otherwise both the Master AU and the BS-GU will send conflicting
synchronization signals to the Slave AUs. During this process, connectivity with the
Subscriber Units will be interrupted. It is recommended to perform the upgrade during a
planned downtime or at a time of minimal traffic. Properly configuring the value of the
Number of Hopping Frequencies parameter in the BS-GU is mandatory for proper
operation of the base station. All other parameters of the BS-GU module may be
configured later as they do not impact the operation of the system.
WARNING:
Deactivate the power to the BS-GU unit before connecting it to a GPS antenna. Switch
on the BS-GU only after the GPS antenna has been connected.