User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
1-22
BreezeACCESS Version 4.3 Installation
Manual Revision: 3.0
Table 1-10: BS-GU Connectors
Table 1-11: BS-GU LEDs and Switches
Connector Name Functionality
SYNC IN Receives signals from the GPS antenna unit.
If more than one collocated BS-GU module is daisy-chained, this
connector is used by a “Slave” module to receive signals from the
“Master” module’s SYNC OUT connector.
SYNC OUT Transfers the signals received on the SYNC IN port.
If the module is a “Master” operating in “local” mode, the internally
generated synchronization signals are also transferred to the “Slave”
via this connector.S
AL IN Four connections to receive indications from external devices.
AL OUT Three relay outputs to external devices.
ETH Ethernet 10BaseT interface. Use a straight cable to connect directly to
a PC. Use a crossed cable to connect to a hub.
LED Name Functionality
LED Name Functionality
PWR (green) On – Power supply functioning properly.
Off – Power supply not functioning properly.
OK (green) On – Proper signals are being received from the GPS antenna.
Off – The GPS antenna is not connected or it is not functioning
properly.
A1 (red) On – Alarm In 1 (external) is activated.
A2 (red) On – Alarm In 2 (external) is activated.
A3 (red) On – Alarm In 3 (external) is activated.
A4 (red) On – Alarm In 4 (external) is activated.
A5, A6 (red) Reserved for future use.
Ethernet Activity -Ethernet
Connector embedded LED
(green)
On – Receiving traffic on the Ethernet port.
Off – No activity on the Ethernet port.
Ethernet Integrity -Ethernet
Connector Embedded LED
(orange)
On – Unit is connected to an Ethernet segment.
Off – Unit is not connected to an Ethernet segment.
Reset Press this button with a paper clip or similar object in order to reset
the unit.