User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
E-8
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
Send SU
Wireless Quality
Trap
SU Disable Trap Sending,
Enable Trap Sending
Enable Trap
Sending
Yes
Send Parameter
Changed Trap
AU, SU Disable Trap Sending,
Enable Trap Sending
Enable Trap
Sending
Yes
Send GPS Alarm
In Trap
GU Disable Trap Sending,
Enable Trap Sending
Enable Trap
Sending
Yes
Send GPS Alarm
Out Trap
GU Disable Trap Sending,
Enable Trap Sending
Enable Trap
Sending
Yes
Send GPS UTC
Status Trap
GU Disable Trap Sending,
Enable Trap Sending
Enable Trap
Sending
Yes
Send Power Up
From Reset Trap
All Disable Trap Sending,
Enable Trap Sending
AU & GU:
Enable Trap
Sending
SU: Disable
Trap Sending
Yes
Send Monitor
Status Trap
All Disable Trap Sending,
Enable Trap Sending
Enable Trap
Sending
Yes
Send Cold \
Warm Start Trap
All Disable Trap Sending,
Enable Trap Sending
AU & GU:
Enable Trap
Sending.
SU: Disable
Trap Sending
Yes
Send AU Loss Of
Sync Trap
BS-AU Disable Trap Sending,
Enable Trap Sending
Enable Trap
Sending
Yes
Send AU Alarms
Traps
IF-based AU Disable Traps Sending,
Enable Traps Sending
Enable Traps
Sending
Yes
Parameter Unit Range Default
Run-
Time
Updated