User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Appendix E
E-5
BreezeACCESS Version 4.3 System Manual
Receive
Attenuation Control
SU-A/E (IF
based units)
0, 10dB, 25dB 0 No
Maximum Data
Rate
AU, SU 1, 2 and 3Mbps 3Mbps No
AU Transmission
Rate Control
SU Disable,
Enable
Disable No
Acknowledge
Delay Limit
AU, SU Low, Medium,
High
Low No
Maximum Number
of Associations
AU 1 – 512 512 Yes
Call Aging Time AU 1 (no aging), 2-
50,000
(seconds)
1800 seconds No
Maximum Voice
Sessions
AU 0 – 50 12 Yes
ACSE Option AU and GU Disable,
Enable
Disable No
ACSE Maximum
Voice Sessions
AU 0 – 21 21 Yes
ACSE Number Of
Retransmissions
For Data
AU, SU 0 – 100 6 No
ACSE Number Of
Retransmissions
For Voice
AU, SU
with voice
0 – 100 30 No
ATPC Option IF Based
AU, SU
Disable,
Enable
AU: Disable
SU: Enable
Yes
Maximum RSSI
Level
IF Based
AU
-100 to 0
(dBm) -64 (dBm)
Yes
Minimum RSSI
Level
IF Based
AU
-100 to 0
(dBm) -74 (dBm)
Yes
Minimum Interval
Between ATPC
Messages
IF Based
AU
0-3600
(seconds)
120 (seconds) Yes
RSSI Memory
Factor
IF Based
AU
-1 to 32 5 Yes
ATPC Power Level
Steps
IF Based
AU
1-100 (%) 1 Yes
ATPC Maximum
Last Level Time
After Reset
SU 0-3600
(seconds)
30 (seconds) Yes
Parameter Unit Range Default
Run-Time
Updated