User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Appendix C
C-47
BreezeACCESS Version 4.3 System Manual
Trap (Number) Description Variables
*NoAssociationsOnTRAP (201) An IF-based AU alarm.
Alarm was set on: The AU
was reset 3 consecutive
times as a result of no
association with any SU, and
before that the AU was
associated with at least
Minimum Number Of SUs.
*TrapAUAlarmsSeverity
*NoAssociationsOffTRAP (202) Alarm was set off: At least
one SU became associated
with the AU.
The alarm will be set off also
after activating Clear All
Alarms or after disabling the
AU Alarms Option.
*AllAssociationsLostOnTRAP (203) Alarm was set on: No
response from any SU, and
the previous average
number of responding SUs
was at least Minimum
Number Of SUs.
*TrapAUAlarmsSeverity
*TrapAverageNumberOfRespondingSUs
*AllAssociationsLostOffTRAP (204) Alarm was set off: At least
one SU responded to last
polling messages.
The alarm will be set off also
after activating Clear All
Alarms or after disabling the
AU Alarms Option.
*TrapCurrentNumberOfRespondingSUs
*AUTxPowerLevelDecreaseOnTRAP(205) Alarm was set on: The
decrease in the SU Rx
Power Average Delta (the
inverse value of the SU Rx
Power Average Delta) is
higher than the SU Rx Power
Decrease Threshold, and the
number of SUs that
responded to both of the last
two polling messages is at
least 5.
*TrapAUAlarmsSeverity
*TrapSURxPowerAverageDelta
*AUTxPowerLevelDecreaseOffTRAP (206) The alarm will be set off after
activating Clear All Alarms or
after disabling the AU Alarms
Option.
*AURxSignalStrengthDecreaseOnTRAP(207) Alarm was set on: The
decrease in the AU Rx
Power Average Delta (the
inverse value of the AU Rx
Power Average Delta) is
higher than the AU Rx Power
Decrease Threshold, and the
number of SUs that
responded to both of the last
two polling messages is at
least 5.
*TrapAUAlarmsSeverity
*TrapAURxPowerAverageDelta
*AURxSignalStrengthDecreaseOffTRAP (208) The alarm will be set off after
activating Clear All Alarms or
after disabling the AU Alarms
Option.