User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-44
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
General Info MIB
Supported Traps
Note: * is used instead of the brzacc prefix
Trap Associated Parameters
*MinimumFlashDetectTimeOut
710.3.4.3.3.1
(*TimeOuts 1)
The minimum on-hook time for identifying it
as a Hook Flash.
Integer
0-2,000 (milliseconds)
*MaximumFlashDetectTimeOut
710.3.4.3.3.2
(*TimeOuts 2)
The maximum on-hook time for identifying
it as a Hook Flash.
Integer
0-2,000 (milliseconds)
*DisconnectTimeOut
710.3.4.3.3.3
(*TimeOuts 3)
The minimum time for decision on an on-
hook (disconnect) condition.
Integer
0-2,000 (milliseconds)
*InterDigitTimeOut
710.3.4.3.3.4
(*TimeOuts 4)
Applicable only for pulse dialing. The
minimum time between two consecutive
pulses to be considered as separating
between two digits.
Integer
0-2,000 (milliseconds)
*CalledPartyReleaseTimeOut
710.3.4.3.3.5
(*TimeOuts 5)
The minimum time for an on-hook signal on
the called party side to be considered as
call disconnect.
Integer
0-10,000 (milliseconds)
MIB Parameter
(Location in Parenthesis)
Description Values
*GenInfo 710.3.4.9
(breezecomPrvRev 9)
General Info MIB
brzHoppingStandardProtected Applicable to AU and SU in
BreezeACCESS II family. Read-only.
Indicates if the Hopping Standard (Band)
can be changed (if protected or not).
Integer
notProtected (1)
protected (2)
MIB Parameter
(Location in Parenthesis)
Description Values
*Traps
710.3.3.14
(brzAccessMib 14)
*TrapSUMacAddr
710.3.3.14.1
(*Traps 1)
Applicable to AU only. SU MAC address. MAC address
*TrapRssiQuality
710.3.3.14.2
(*Traps 2)
Applicable to SU only. RSSI level of the received signal. Integer
*TrapLastRssiQuality
710.3.3.14.3
(*Traps 3)
Applicable to SU only. RSSI level of the received signal
from the last AU with which the SU was associated.
Integer
*TrapText
710.3.3.14.4
(*Traps 4)
Textual string for future use. DisplayString
MIB Parameter
(Location in Parenthesis)
Description Values