User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-38
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
Alarms Parameters
MIB Parameter
(Location in Parenthesis)
Description Values/Range
*Alarms
710.3.3. 20
(brzAccessMib 20)
Alarms parameters
*GpsAlarms
710.3.3. 20.1
(*Alarms 1)
Applicable to GU only. GPS Alarms parameters.
*AlarmInTable
710.3.3. 20.1.1
(*GpsAlarms 1)
Applicable to GU only. Names and status of Alarms-In. Not
accessible.
*AlarmInTableEntry
710.3.3. 20.1.1.1
(*AlarmInTable 1)
Applicable to GU only. An Alarms In table entry. Not
accessible.
*AlarmInIdx
710.3.3. 20.1.1.1.1
(*AlarmInTableEntry 1)
Applicable to GU only. Read-only. Alarms In table index Integer
1-10
*AlarmInName
710.3.3. 20.1.1.1.2
(*AlarmInTableEntry 2)
Applicable to GU only. Alarm In name. Alarms 1 to 4 can
receive a name. The other are read-only.
DisplayString
(SIZE(0..31))
*AlarmInStatus
710.3.3. 20.1.1.1.3
(*AlarmInTableEntry 3)
Applicable to GU only. Read-only. The status (off or on) of
Alarm In entry.
Integer
off (0)
on (1)
na (255)
*AlarmOutTable
710.3.3. 20.1.2
(*GpsAlarms 2)
Applicable to GU only. Names, definition, control and status of
Alarms-Out. Not accessible.
*AlarmOutTableEntry
710.3.3. 20.1.2.1
(*AlarmOutTable 1)
Applicable to GU only. An Alarms Out table entry. Not
accessible.
*AlarmOutIdx
710.3.3. 20.1.2.1.1
(*AlarmOutTableEntry 1)
Applicable to GU only. Read-only. Alarms Out table index Integer
1-3
*AlarmOutName
710.3.3. 20.1.2.1.2
(*AlarmOutTableEntry 2)
Applicable to GU only. Alarm Out name. The other are read-
only.
DisplayString
(SIZE(0..31))
*AlarmOutDefinition
710.3.3. 20.1.2.1.3
(*AlarmOutTableEntry 3)
Applicable to GU only. Enter an Alarm-In number to activate
the Alarm-Out when this Alarm-In is ON. Enter A to activate the
Alarm-Out if ANY of the Alarms-In are ON. Enter N for
NONE (never activate the Alarm Out).
DisplayString
(SIZE(0..2))
1-10, A, N
*AlarmOutControl
710.3.3. 20.1.2.1.4
(*AlarmOutTableEntry 4)
Applicable to GU only. Alarm out control:
off (0) – turn alarm off.
on (1) – turn alarm on.
auto (2)-activate according to status of relevant alarm-in in
accordance with Alarm Out Definition.
Integer
off (0)
on (1)
auto (2)
na (255)
*AlarmOutStatus
710.3.3. 20.1.2.1.5
(*AlarmOutTableEntry 5)
Applicable to GU only. Read-only. The status (off or on) of
Alarm Out entry.
Integer
off (0)
on (1)
na (255)