User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-36
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
IP Parameters
System Information Parameters
MIB Parameter
(Location in
Parenthesis)
Description Values/Range
*IpParams
710.3.3. 11
(brzAccessMib 11)
*UnitIpAddress
710.3.3. 11.1
(*IpParams 1)
Applicable to all products. IP address of the unit. IP address
*SubNetMask
710.3.3. 11.2
(*IpParams 2)
Applicable to all products. Subnet mask of the unit. IP address
*DefaultGWAddress
710.3.3. 11.3
(*IpParams 3)
Applicable to all products. Default gateway IP address of the
unit.
IP address
*UseDhcp
710.3.3. 11.4
(*IpParams 4)
Applicable to all products. DHCP client mode of operation.
disabled: Use regular (manual) methods to configure IP
parameters.
dHCP Only: Use DHCP server to configure IP parameters.
automatic: Use DHCP server to configure IP parameters. If a
DHCP server is not available, use configured values for
*UnitIpAddress, *SubNetMask and *DefaultGWAddress.
Integer
disable (0)
dHCPOnly (1)
automatic (2)
*RunIPaddr
710.3.3. 11.5
(*IpParams 5)
Applicable to all products. Read-only: The run-time IP
address. If DHCP is used the Run Time IP Address is the
address given to the unit by the server. Otherwise it is the
manualy configured address.
IP address
*RunSubNetMask
710.3.3. 11.6
(*IpParams 6)
Applicable to all products. Read-only: The run-time Subnet
Mask. If DHCP is used the Run Time Subnet Mask is the
mask given to the unit by the server. Otherwise it is the
manualy configured mask.
IP address
*RunDefaultIPGateway
710.3.3. 11.7
(*IpParams 7)
Applicable to all products. Read-only: The run-time Gateway
IP address. If DHCP is used the Run Time Gateway IP
Address is the address given to the unit by the server.
Otherwise it is the manualy configured address.
IP address
*AccessToDHCP
710.3.3. 11.8
(*IpParams 8)
Applicable to all products. The port to be used for
communicating with a DHCP server. (In GU only the
fromEthernetOnly option is available).
Integer
fromWlanOnly(0)
fromEthernetOnly(1)
fromBoth(2)
MIB Parameter
(Location in Parenthesis)
Description Values/Range
*SysInfo
710.3.3. 13 (brzAccessMib 13)
*UnitHwVersion
710.3.3. 13.1
(*SysInfo 1)
Applicable to all products. Read-only:
Hardware platform version.
DisplayString
(SIZE(0..32))
*VoiceHwVersion
710.3.3. 13.2
(*SysInfo 2)
Applicable only to SU with voice. Read-only:
Voice hardware platform version.
DisplayString
(SIZE(0..32))
*SoftwareVersion
710.3.3. 13.3
(*SysInfo 3)
Applicable to all products. Read-only: Running
software version.
DisplayString
(SIZE(0..32))
*ShadowVersion
710.3.3. 13.4
(*SysInfo 4)
Applicable to all products. Read-only: Shadow
software version.
DisplayString
(SIZE(0..32))
*SupportedMibVersion
710.3.3. 13.5
(*SysInfo 5)
Applicable to all products. Read-only: The
supported private MIB versions.
DisplayString
(SIZE(0..32))
*UnitMacAddress
710.3.3. 13.6
(*SysInfo 6)
Applicable to all products. Read-only, Unit
hardware MAC address.
MAC address