User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Appendix C
C-35
BreezeACCESS Version 4.3 System Manual
*EraseEventLog
710.3.3. 10.10.3
(*EventLog 3)
Applicable to all products. Deletes
all entries from the Event Log file.
Integer
cancel (0)
erase (1)
*SaveCurrentConfigurationAs
OperatorDefaults
710.3.3. 10.12
(*UnitControl 12)
Applicable to all products. Saves the
current configuration as Operator
Defaults.
Integer
cancel (0)
saveAsDefaults (1)
*ExitMonitorOrTelnet
710.3.3. 10.13
(*UnitControl 13)
Applicable to all products. Exit the
monitor program.
Integer
cancelOperation (0)
exit (1)
*AutoConfig
710.3.3. 10.14
(*UnitControl 14)
Auto configuration Parameters
*AutoConfigOption
710.3.3. 10.14.1
(*AutoConfig 1)
Disable/enable the Auto
Configuration feature
Integer
disable (0)
enable (1)
na (255)
*RequestAutoConfig
710.3.3. 10.14.2
(*AutoConfig 2)
Initiate a request for an Auto
Configuration file.
Integer
cancelRequest (0)
request (1)
*AutoConfigReceived
710.3.3. 10.14.3
(*AutoConfig 3)
Indicates whether an Auto
Configuration file was received.
Integer
notReceived (0)
received (1)
*SNMPReadESSID
710.3.3. 10.15
(*UnitControl 15)
Applicable to AU and SU. Enables
or disables viewing (get) the values
of ESSID and RunTimeESSID with
the SNMP Read Community string.
Integer
disable (1)
enable (2)
MIB Parameter
(Location in Parenthesis)
Description Values/Range