User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-32
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
*MinorAlarmThreshold
710.3.3. 8.7.4.1.1.5
(*TrafficStatisticsEntry 5)
Applicable to IF-based AU only.
Read-write. The threshold for
activating a minor severity alarm for
the relevant statistics type. Another
prerequisite for activating the alarm
is that the difference between the
Traffic Statistics Current Rate and
the previous Traffic Statistics
Average Rate exceeds the Traffic
Statistics Minor Alarm Minimum
Delta.
Integer
1 – 100 (%)
*MajorAlarmThreshold
710.3.3. 8.7.4.1.1.6
(*TrafficStatisticsEntry 6)
Applicable to IF-based AU only.
Read-write. The threshold for
activating a major severity alarm for
the relevant statistics type.
Integer
1 – 100 (%)
*AURxPowerTest
710.3.3. 8.7.5
(*AUAlarms 5)
Applicable to IF-based AU only. AU
Alarms AU Rx Power Tests
parameters and measurement
results.
*AURxPowerAverageDelta
710.3.3. 8.7.5.1
(*AURxPowerTest 1)
Applicable to IF-based AU only.
Read-only. The average for all SUs
that responded to the last two
polling messages of the difference
between the last RSSI at the AU
and the previous (one before last)
RSSI. (A negative value indicates
that the average RSSI was
decreased).
DisplayString
-99 to 99 (dBm)
*AURxPowerDecreaseThreshold
710.3.3. 8.7.5.2
(*AURxPowerTest 2)
Applicable to IF-based AU only.
Read-write. The Minimum decrease
in the value of the AU Rx Power
Average Delta that will trigger an
alarm. (If the AU Rx Power
Decrease Threshold is +X, an alarm
will be generated if the AU Rx
Power Average Delta is smaller
than or equal to –X)
Integer
1 – 99 (dBm)
*SURxPowerTest
710.3.3. 8.7.6
(*AUAlarms 6
Applicable to IF-based AU only. AU
Alarms SU Rx Power Tests
parameters and measurement
results.
*SURxPowerAverageDelta
710.3.3. 8.7.6.1
(*SURxPowerTest 1)
Applicable to IF-based AU only.
Read-only. The average for all SUs
that responded to the last two
polling messages of the difference
between the last RSSI at the SU
and the previous (one before last)
RSSI. (A negative value indicates
that the average RSSI was
decreased).
DisplayString
-99 to 99 (dBm)
*SURxPowerDecreaseThreshold
710.3.3. 8.7.6.2
(*SURxPowerTest 2)
Applicable to IF-based AU only.
Read-write. The Minimum decrease
in the value of the SU Rx Power
Average Delta that will trigger an
alarm. (If the SU Rx Power
Decrease Threshold is +X, an alarm
will be generated if the SU Rx
Power Average Delta is smaller
than or equal to –X)
Integer
1 – 99 (dBm)
*RespondingSUs
710.3.3. 8.7.7
(*AUAlarms 7)
Applicable to IF-based AU only.
Responding SUs parameters.
*CurrentNumberOfRespondingSUs
710.3.3. 8.7.7.1
(*RespondingSUs 1)
Applicable to IF-based AU only.
Read-only. The number of SUs that
responded to the last polling
message.
Integer
na (255)
*AverageNumberOfRespondingSU
s
710.3.3. 8.7.7.2
(*RespondingSUs 2)
Applicable to IF-based AU only.
Read-only. The average number of
SUs that responded to polling
message since power-up or since
the AU Alarms Option was enabled.
Integer
na (255)
MIB Parameter
(Location in Parenthesis)
Description Values/Range