User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-28
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
*VoiceTrafficTxFrames
710.3.3. 8.2.4.1
(*VoiceCounters 1)
Applicable to SU with voice support
only. Read-only. Counts the number
of voice frames, including fax and
T.38 redundant frames, that were
transmitted to the wireless link.
Counter
*VoiceTrafficRxFrames
710.3.3. 8.2.4.2
(*VoiceCounters 2)
Applicable to SU with voice support
only. Read-only. Counts the number
of voice frames, including fax and
T.38 redundant frames, that were
received from the wireless link.
Counter
*VoiceTrafficTxBytes
710.3.3. 8.2.4.3
(*VoiceCounters 3)
Applicable to SU with voice support
only. Read-only. Counts the number
of voice bytes, including fax and
T.38 redundant bytes, that were
transmitted to the wireless link.
Counter
*VoiceTrafficRxBytes
710.3.3. 8.2.4.4
(*VoiceCounters 4)
Applicable to SU with voice support
only. Read-only. Counts the number
of voice bytes, including fax and
T.38 redundant bytes, that were
received from the wireless link
Counter
*VoiceTrafficResetCounters
710.3.3. 8.2.4.5
(*VoiceCounters 5)
Applicable to SU with voice support
only. Reset the voice counters.
noReset (0)
reset (1)
na (255)
*PerRateCounters
710.3.3. 8.2.5
(*TrafficStatistics 5)
Applicable to SU and AU.
*ResetPerRateCounters
710.3.3. 8.2.5.1
(*PerRateCounters 1)
Applicable to AU and SU. Resets
the Per Rate Counters.
noReset (0)
reset (1)
na (255)
*PerRateCountersSU
710.3.3. 8.2.5.2
(*PerRateCounters 2)
SU Per Rate Counters.
*TxFrames1M
710.3.3. 8.2.5.2.1
(*PerRateCountersSU 1)
Applicable to SU only. Read-only.
Counts the total number of frames
(excluding retransmissions) that
were transmitted over the wireless
link at 1Mbps.
Counter
*TxFrames2M
710.3.3. 8.2.5.2.2
(*PerRateCountersSU 2)
Applicable to SU only. Read-only.
Counts the total number of frames
(excluding retransmissions) that
were transmitted over the wireless
link at 2Mbps.
Counter
*TxFrames3M
710.3.3. 8.2.5.2.3
(*PerRateCountersSU 3)
Applicable to SU only. Read-only.
Counts the total number of frames
(excluding retransmissions) that
were transmitted over the wireless
link at 3Mbps.
Counter
*ReTxFrames1M
710.3.3. 8.2.5.2.4
(*PerRateCountersSU 4)
Applicable to SU only. Read-only.
Counts the total number of frames
that were retransmitted over the
wireless link at 1Mbps.
Counter
*ReTxFrames2M
710.3.3. 8.2.5.2.5
(*PerRateCountersSU 5)
Applicable to SU only. Read-only.
Counts the total number of frames
that were retransmitted over the
wireless link at 2Mbps.
Counter
*ReTxFrames3M
710.3.3. 8.2.5.2.6
(*PerRateCountersSU 6)
Applicable to SU only. Read-only.
Counts the total number of frames
that were retransmitted over the
wireless link at 3Mbps.
Counter
*ReceivingUnits
710.3.3. 8.3
(*SiteSurvey 3)
*AveragePower
710.3.3. 8.3.1
(*ReceivingUnits 1)
Applicable to SU only. Read-only.
Represents the average Signal
Strength of received frames.
DisplayString (SIZE(32))
*RssiOrDbm
710.3.3. 8.3.2
(*ReceivingUnits 2)
Applicable to SU and AU. Selects
the measurement units used to
display the average received signal
strength.
Integer
rssi (0)
dBm (1)
MIB Parameter
(Location in Parenthesis)
Description Values/Range