User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Appendix C
C-27
BreezeACCESS Version 4.3 System Manual
*TotalTxErrorsAckTOut
710.3.3. 8.2.3.23
(*WlanCounters 23)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred because
of an Acknowledge Timeout–a
frame that was not acknowledged
within the time defined by the
Acknowledge Delay Limit
parameter.
Counter
*TotalTxErrorsFail
710.3.3. 8.2.3.24
(*WlanCounters 24)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred because
of an internal timeout in the modem.
Counter
*TotalTxErrorsAckCrc
710.3.3. 8.2.3.25
(*WlanCounters 25)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred because
of a CRC error in the ACK
message.
Counter
*TotalTxErrorsRtsc
710.3.3. 8.2.3.26
(*WlanCounters 26)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred because
RTS was sent but CTS was not
received (RTS collision).
Counter
*TotalTxErrorsEod
710.3.3. 8.2.3.27
(*WlanCounters 27)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred because
there was not enough time left to
transmit the message prior to the
end of the Dwell.
Counter
*TotalReceivedDataFrames
710.3.3. 8.2.3.28
(*WlanCounters 28)
Applicable to SU and AU.
Read-only. The total number of data
frames received from the wireless
media, including duplicate frames.
Counter
*ReceivedDataFramesHigh
710.3.3. 8.2.3.29
(*WlanCounters 29)
Applicable to SU and AU.
Read-only. The total number of data
frames received from the wireless
media and routed via the receive
High queue, including duplicate
frames.
Counter
*ReceivedDataFramesLow
710.3.3. 8.2.3.30
(*WlanCounters 30)
Applicable to SU and AU.
Read-only. The total number of data
frames received from the wireless
media and routed via the receive
Low queue, including duplicate
frames.
Counter
*BadFragmentsReceived
710.3.3. 8.2.3.31
(*WlanCounters 31)
Applicable to SU and AU.
Read-only. The number of frames
received from the wireless media
with errors (CRC errors).
Counter
*DuplicatedFramesDiscarded
710.3.3. 8.2.3.32
(*WlanCounters 32)
Applicable to SU and AU.
Read-only. The number of frames
discarded due to receiving multiple
copies.
Counter
*InternallyDiscardedMirCir
710.3.3. 8.2.3.33
(*WlanCounters 33)
Applicable to SU and AU.
Read-only. The number of data
frames received from the Ethernet
port that were discarded by the MIR/
CIR mechanism to avoid exceeding
the maximum allowed information
rate.
Counter
*TotalTxUnicastFramesToWireles
s
710.3.3. 8.2.3.34
(*WlanCounters 34)
Applicable to SU and AU.
Read-only. The number of unicast
frames successfully transmitted to
the wireless media, excluding
retransmissions.
Counter
*VoiceCounters
710.3.3. 8.2.4
(*TrafficStatistics 4)
Applicable to SU with voice support
only.
MIB Parameter
(Location in Parenthesis)
Description Values/Range