User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-26
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
*SubmittedFramesLow
710.3.3. 8.2.3.11
(*WlanCounters 11)
Applicable to SU and AU.
Read-only. Counts the number of
frames submitted to the bridge via
the Low queue for transmission to
the wireless media. When the
ACSE Option is enabled, it counts
data and RTP frames. When the
ACSE Option is disabled, it counts
only data frames.
Counter
*SubmittedFramesVoice
710.3.3. 8.2.3.12
(*WlanCounters 12)
Applicable to SU and AU only when
the ACSE Option is enabled.
Read-only. Counts the number of
voice frames, including fax and T.38
redundant frames, submitted to the
bridge for transmission to the
wireless media.
Counter
*FramesDroppedData
710.3.3. 8.2.3.13
(*WlanCounters 13)
Applicable to SU and AU only when
the ACSE Option is enabled.
Read-only. The number of dropped
data frames. The data frames that
were retransmitted to the extent of
the maximum allowed number of
retransmissions for data frames
without being acknowledged.
Counter
*FramesDroppedVoice
710.3.3. 8.2.3.14
(*WlanCounters 14)
Applicable to SU and AU only when
the ACSE Option is enabled.
Read-only. The number of dropped
voice frames, including fax and T.38
redundant frames. The voice
frames that were retransmitted to
the extent of the maximum allowed
number of retransmissions for voice
frames without being
acknowledged.
Counter
*TotalRetransmittedFrames
710.3.3. 8.2.3.15
(*WlanCounters 15)
Applicable to SU and AU.
Read-only. The total number of
retransmissions of frames (counts
all unsuccessful transmissions/
retransmissions).
Counter
*RetransmittedFramesData
710.3.3. 8.2.3.16
(*WlanCounters 16)
Applicable to SU and AU only when
the ACSE Option is enabled.
Read-only. The total number of
retransmissions of data frames
(counts all unsuccessful
transmissions/retransmissions).
Counter
*RetransmittedFramesVoice
710.3.3. 8.2.3.17
(*WlanCounters 17)
Applicable to SU and AU only when
the ACSE Option is enabled.
Read-only. The total number of
retransmissions of voice frames,
including fax and T.38 redundant
frames (counts all unsuccessful
transmissions/retransmissions).
Counter
*TotalTxErrors
710.3.3. 8.2.3.19
(*WlanCounters 19)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred.
Counter
*TotalTxErrors
710.3.3. 8.2.3.20Hw
(*WlanCounters 20)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred due to an
hardware problem.
Counter
*TotalTxErrorsAbr
710.3.3. 8.2.3.21
(*WlanCounters 21)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred because
transmission has been aborted
before completion due to internal
problems in the DSP.
Counter
*TotalTxErrorsCsl
710.3.3. 8.2.3.22
(*WlanCounters 22)
Applicable to SU and AU.
Read-only. The number of transmit
errors that have occurred because
transmission was cancelled due to
the modem being busy receiving
data.
Counter
MIB Parameter
(Location in Parenthesis)
Description Values/Range