User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Appendix C
C-25
BreezeACCESS Version 4.3 System Manual
*TotalRxFramesFromWireless
710.3.3. 8.2.3.2
(*WlanCounters 2)
Applicable to SU and AU.
Read-only. The total number of
frames that were received from the
wireless media. The count includes
data and control and management
frames, including beacons received
from the AU. The count does not
include frames that were discarded
internally, bad frames and duplicate
frames.
Counter
*TotalRetransmittedFragments
710.3.3. 8.2.3.3
(*WlanCounters 3)
For future use Counter
*WlanFramesDropped
710.3.3. 8.2.3.4
(*WlanCounters 4)
Applicable to SU and AU.
Read-only. The number of dropped
frames. The frames that were
retransmitted to the extent of the
maximum allowed number of
retransmissions without being
acknowledged.
Counter
*TransmittedFramesToWirelessDat
a
710.3.3. 8.2.3.5
(*WlanCounters 5)
Applicable to SU and AU only when
the ACSE Option is enabled.
Read-only. The number of data
frames transmitted to the wireless
media. The count includes one
count for each data frame that was
transmitted successfully (excluding
retransmissions).
Counter
*TransmittedFramesToWirelessVoi
ce
710.3.3. 8.2.3.6
(*WlanCounters 6)
Applicable to SU and AU only when
the ACSE Option is enabled.
Read-only. The number of voice
frames, including fax and redundant
T.38 frames, transmitted to the
wireless media. The count includes
one count for each frame that was
transmitted successfully (excluding
retransmissions).
Counter
*TransmittedFramesToWirelessBea
con
710.3.3. 8.2.3.7
(*WlanCounters 7)
Applicable to AU only when the
ACSE Option is enabled.
Read-only. The number of beacons
transmitted to the wireless media.
The count includes one count for
each beacon that was transmitted
successfully (excluding
retransmission attempts).
Counter
*TotalSubmittedFrames
710.3.3. 8.2.3.8
(*WlanCounters 8)
Applicable to SU and AU.
Read-only. The total number of data
and RTP frames submitted to the
bridge for transmission to the
wireless media. The count does not
include control and management
frames, and retransmissions.
Counter
*SubmittedFramesHigh
710.3.3. 8.2.3.9
(*WlanCounters 9)
Applicable to SU and AU.
Read-only. Counts the number of
frames submitted to the bridge via
the High queue for transmission to
the wireless media. When the
ACSE Option is enabled, it counts
data and RTP frames. When the
ACSE Option is disabled, it counts
only data frames.
Counter
*SubmittedFramesMid
710.3.3. 8.2.3.10
(*WlanCounters 10)
Applicable to SU and AU.
Read-only. Counts the number of
frames submitted to the bridge via
the Mid queue for transmission to
the wireless media. When the
ACSE Option is enabled, it counts
data and RTP frames. When the
ACSE Option is disabled, it counts
only data frames.
Counter
MIB Parameter
(Location in Parenthesis)
Description Values/Range