User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-24
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
Site Survey Parameters
MIB Parameter
(Location in Parenthesis)
Description Values/Range
*SiteSurvey
710.3.3. 8
(brzAccessMib 8)
PerHopStatisticsTable
710.3.3. 8.1
(*SiteSurvey 1)
Applicable to SU and AU. Statistics
accumulated since last reset and
average RSSI per frequency for all
hopping frequencies in the
(sequence). Not Accessible.
hopSeqEntry
710.3.3. 8.1.1
(perHopStatisticsTable 1)
Applicable to SU and AU. A Per
Hop Statistics Table entry. Not
accessible.
wPperHopStatisticsTable
710.3.3. 8.1.1.1
(hopSeqEntry 1)
Applicable to SU and AU. Read-
only. The channel number
according to the hopping sequence.
Integer
hopTracerRx
710.3.3. 8.1.1.2
(hopSeqEntry 2)
Applicable to SU and AU. Read-
only. The accumulated number of
frames received since last reset at
the applicable frequency.
Integer
hopTracerTx
710.3.3. 8.1.1.3
(hopSeqEntry 3)
Applicable to SU and AU. Read-
only. The accumulated number of
frames transmitted since last reset
at the applicable frequency.
Integer
hopTracerRetries
710.3.3. 8.1.1.4
(hopSeqEntry 4)
Applicable to SU and AU. Read-
only. The accumulated number of
frames retransmitted since last
reset at the applicable frequency.
Integer
hopTracerRSSI
710.3.3. 8.1.1.5
(hopSeqEntry 5)
Applicable to SU and AU. Read-
only. The average RSSI of frames
received at the applicable
frequency.
DisplayString (SIZE(20))
* hopTracerFreq
710.3.3. 8.1.1.6
(hopSeqEntry 6)
Applicable to SU and AU. Read-
only. The frequency in MHz of the
entry.
DisplayString (SIZE(9))
*TrafficStatistics
710.3.3. 8.2
(*SiteSurvey 2)
Applicable to SU and AU. Traffic
Statistics parameters.
*ResetTrafficCounters
710.3.3. 8.2.1
(*TrafficStatistics 1)
Applicable to SU and AU. Resets
the Ethernet Counters
(*EthCounters) and the Wireless
Link Counters (*WlanCounters).
Integer
noReset (0)
reset (1)
*EthCounters
710.3.3. 8.2.2
(*TrafficStatistics 2)
Applicable to SU and AU. Ethernet
counters.
*TotalRxFramesViaEthernet
710.3.3. 8.2.2.1
(*EthCounters 1)
Applicable to SU and AU.
Read-only. Total number of frames
received via the Ethernet port.
Counter
*TxWirelessToEthernet
710.3.3. 8.2.2.2
(*EthCounters 2)
Applicable to SU and AU.
Read-only. Total number of frames
transmitted to the Ethernet port.
Counter
*WlanCounters
710.3.3. 8.2.3
(*TrafficStatistics 3)
Applicable to SU and AU. Wireless
link counters.
*TotalTxFramesToWireless
710.3.3. 8.2.3.1
(*WlanCounters 1)
Applicable to SU and AU.
Read-only. The number of frames
transmitted to the wireless media.
The count includes one count for
each data or RTP frame that was
transmitted successfully (excluding
retransmissions), and also the
number of transmitted control and
management frames.
Counter