User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-18
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
*OperatorESSID
710.3.3. 6.21
(*AirInterface 21)
Applicable to AU only. A secondary
ESSID to support upgrade of
existing installations. All AUs in the
region should be configured to the
same Operator ESSID to allow a
new SU to associate with any AU.
Accessible only with SNMP Write
Community
DisplayString (SIZE(31))
Up to 31 printable ASCII characters, case
sensitive.
*RunTimeESSID
710.3.3. 6.22
(*AirInterface 22)
Applicable to SU only. Read-only.
The ESSID of the associated AU.
Accessible only with SNMP Write
Community.Can be viewed (get) with
the SNMP Read Community only if
*SNMPReadESSID is enabled.
DisplayString (SIZE(31))
Up to 31 printable ASCII characters, case
sensitive.
*BestAu
710.3.3. 6.23
(*AirInterface 23)
Best AU Parameters
*BestAuSupport
710.3.3. 6.23.1
(*BestAu 1)
Applicable to SU only. Disable/
enable the Best AU selection
mechanism.
Integer
disable (0)
enable (1)
na (255)
*BestAuNoOfScanningAttempts
710.3.3. 6.23.2
(*BestAu 2)
Applicable to SU only. The number
of scanning attempts to collect
information for the Best AU decision.
Integer
1 – 255
*NeighborAuTable
710.3.3. 6.23.3
(*BestAu 3)
Applicable to SU only. A table of
data on neighboring AUs. Not
accessible.
*NeighborAuEntry
710.3.3. 6.23.3.1
(*NeighborAuTable 1)
Applicable to SU only. An entry in
the Neighbor AU Table. Not
accessible.
*NeighborAuMacAdd
710.3.3. 6.23.3.1.1
(*NeighborAuEntry 1)
Applicable to SU only. Read-only. A
MAC address of an AU in the
Neighbor AU Table.
MAC address
*NeighborAuESSID
710.3.3. 6.23.3.1.2
(*NeighborAuEntry 2)
Applicable to SU only. Read-only.
The ESSID of an AU in the Neighbor
AU Table. Accessible only with
SNMP Write Community
DisplayString (SIZE(31))
Up to 31 printable ASCII characters, case
sensitive.
*NeighborAuRssi
710.3.3. 6.23.3.1.3
(*NeighborAuEntry 3)
Applicable to SU only. Read-only.
The received signal strength in RSSI
units of an AU in the Neighbor AU
Table.
Integer
*NeighborAuAssocLoadStatus
710.3.3. 6.23.3.1.4
(*NeighborAuEntry 4)
Applicable to SU only. Read-only.
Neighbor AU association load status
in the Neighbor AU Table.
Integer
notFull (0)
full (1)
na (255)
*NeighborAuMark
710.3.3. 6.23.3.1.5
(*NeighborAuEntry 5)
Applicable to SU only. Read-only.
Neighbor AU mark in the Neighbor
AU Table.
Integer
*NeighborAuIdx
710.3.3. 6.23.3.1.6
(*NeighborAuEntry 6)
Applicable to SU only. Read-only. An
index of an entry in the Neighbor AU
Table.
Integer
*NeighborAuDbm
710.3.3. 6.23.3.1.7
(*NeighborAuEntry 7)
Applicable to SU only. Read-only.
The received signal strength in dBm
of an AU in the Neighbor AU Table.
Integer
*PreferredAuMacAddress
710.3.3. 6.23.5
(*BestAu 5)
Applicable to SU only. The MAC
address of the preferred AU
(overriding the Best AU selection
process. 00...00 (all zeros in
address) means no preferred AU is
set.
MAC Address
MIB Parameter
(Location in Parenthesis)
Description Values/Range