User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
C-12
BreezeACCESS Version 4.3 System Manual
Manual Revision: 3.0
*TransmitDiversity
710.3.3. 6.4
(*AirInterface 4)
Applicable to SU-R, SU-I and AU-I
units only.
Enables the selection of the
antenna(s) to be used for
transmission.
Integer
use2Antennasn (0)
antenna1 (1)
antenna2 (2)
na (255)
*HoppingSequence
710.3.3. 6.5
(*AirInterface 5)
Applicable to AU in BreezeACCESS
II family only.
Determines the hopping sequence to
be used. Different AUs in the same
geographical area should use
different Hopping Sequences from
the same Hopping Set.
The valid range is dependant on the
Country Standard.
Integer
Na (255)
Australia: 1-20
Canada: 1-10
Europe ETSI: 1-26
France: 1-11
Israel: 1-11
Japan: 1-4
Korea: 1-4
Netherlands: 1-5
Spain: 1-9
US FCC: 1-26
Mexico: 1-10
International: 1-26
*HoppingSet
710.3.3. 6.6
(*AirInterface 6)
Applicable to AU in BreezeACCESS
II family only.
Determines the hopping set to be
used. All AUs in the same
geographical area should use the
same Hopping Set.
Integer
1-3
na (255)
*HoppingSync
710.3.3. 6.7
(*AirInterface 7)
Applicable to BS-AU only.
Inter-AU hopping sync functionality
of the unit.
In the BreezeACCESS II family,
synchronization among AUs is not
available with the following Country
Standards: US FCC, Australia,
Canada.
In the BreezeACCESS V family,
synchronization is not available if the
selected hopping band is
ISM US FCC.
Integer
idle (0)
slave (1)
master (2)
na (255)
*HoppingShift
710.3.3. 6.8
(*AirInterface 8)
Applicable to AU in BreezeACCESS
V, XL and MMDS families and in
BreezeACCESS II if *HoppingBands
is frqFlexibleHopping.
Defines a hopping pattern different
from the basic hopping sequence
(Hopping Shift=0). Different
collocated AUs should use different
hopping shifts.
Integer
na (255)
Range 0 to [number of operational channels-1]
MIB Parameter
(Location in Parenthesis)
Description Values/Range