User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
Menus and Parameters
2-79
BreezeACCESS Version 4.3 System Manual
Valid values: A string of up to 20 printable ASCII characters, case
sensitive.
Default value: RadiusSecret1234.
Authentication Parameters Menu
The implementation is based on RFC 2865. The mechanism allows an
SU to synchronize and associate to its AU, then request authentication
from the RADIUS server. Only if the authentication is successful the
user will receive services (data and voice). It is then possible to
download from a remote server the full unit services configuration
(CIR/MIR, Telephone number etc.). If the authentication is not
successful, the data and voice ports of the SU will be blocked.
Authentication Option – To enable or disable the use of RADIUS
for authentication. When this option is enabled and the RADIUS
Server Authentication IP Address is configured to an address
other than 0.0.0.0., the SU enables the RADIUS authentication
feature.
Default selection: Disable
RADIUS Server Authentication IP Address –To define the IP
address of the RADIUS server to be used for authentication.
The default address is 0.0.0.0 (none).
RADIUS Server Authentication Port – Specifies the UDP port
number used by the Radius server for authenticating the clients.
Valid values: 1000 to 65535.
The default value is 1812 (RFC requirement).
Show Authentication Parameters and Status – To display the
Authentication parameters and the current status. The status can
be Idle, Sending Request, Waiting For Response, Sending Challenge,
Authenticated or Rejected.
Accounting Parameters Menu
If the Accounting Option is enabled, then every period defined by the
service provider (Accounting Interval) the NAS (SU) will update the
Radius Accounting Server with the traffic passed through it during the
period. From the Radius Server point of view this period is a session in
accordance with the RFC 2866 definitions. The information is sent to
the Radius Server using the standard Radius attributes. The record
structure is described in RADIUS Record Structure‚ page 2-80.
The Accounting Parameters menu allows enabling the RADIUS client
embedded in the Subscriber Unit and configuring the parameters that
control the transmission of accounting records to a RADIUS billing
server. The Accounting Parameters menu includes the following
parameters:
Accounting Option - To enable or disable the accounting records
transmission feature. When this option is enabled and the RADIUS