User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
2-66
BreezeACCESS Version 4.3 Operations and Administration
Manual Revision: 3.0
Filter Options – Defines the Ethernet broadcast filtering
functionality of the unit. The following options are available:
Disable: No Ethernet broadcast filtering
From Ethernet Only: Filter broadcast messages received from
the Ethernet port
From WLAN Only: Filter broadcast messages received from the
wireless link port
Both From Ethernet & WLAN: Filter broadcast messages
received from both the Ethernet port and the wireless link port
The default selection is Disable.
DHCP Broadcast Override Filter – Enables broadcasting of DHCP
(Dynamic Host Configuration Protocol) messages. This is
independent of the filtering option selected in Filter Options above,
meaning that even if according to the selected filtering option,
broadcast messages should be filtered, DHCP broadcasts will be
transmitted if the Enable DHCP Broadcast option is selected.
Available selections are:
Disable– DHCP Broadcast messages will be filtered or
transmitted according to the general filtering criteria set by the
selected value of the Filter Options parameter.
Enable– DHCP Broadcast messages will be transmitted
regardless of the selected value of the Filter Options parameter.
The default selection is Disable.
PPPoE Broadcast Override Filter – Enables broadcasting of PPPoE
(Point-to-Point Protocol over Ethernet) messages. This is
independent of the filtering option selected in Filter Options above,
meaning that even if according to the selected filtering option
broadcast messages should be filtered, PPPoE broadcasts are
transmitted if the Enable PPPoE Broadcast option is selected.
Available selections are:
Disable– PPPoE Broadcast messages is filtered or transmitted
according to the general filtering criteria set by the selected
value of the Filter Options parameter.
Enable– PPPoE Broadcast messages is transmitted regardless of
the selected value of the Filter Options parameter.
The default selection is Disable.
ARP Broadcast Override Filter –When this option is set to Enable
ARP Broadcast, broadcasting of ARP messages is independent of the
filtering option selected in Filter Options above. This means that
ARP broadcasts are transmitted regardless of which filtering option
is selected for broadcast messages.
Available selections are: