User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
2-58
BreezeACCESS Version 4.3 Operations and Administration
Manual Revision: 3.0
• Management frames generated by the unit will not be
tagged.
The following table summarizes the functionality of the
internal management port in accordance with the value of
the VLAN ID – Management parameter. The table is valid
for all link types.
Table 2-7: Management Port Functionality – AU, SU without Voice Support and GU
Legend: VID-M: VLAN ID-Management
PID-M: VLAN Priority-Management
VLAN ID-Voice & Management (SU with voice support only) –
Applicable for all link types. Sets the VLAN ID for voice and
management frames, identifying remote stations for voice
communication and management purposes. This applies to all
units that support the H.323 protocol and to management
applications using protocols such SNMP, TFTP, ICMP (Ping) and
Telnet. All the servers/stations using these protocols must tag
the frames they send to the unit with the value of the VLAN ID -
Voice & Management parameter.
Valid values: 1 to 4094 or 65535 (No VLAN).
Default value: 65535.
If VLAN ID –Voice & Management is other than 65535:
• Only tagged management frames with matching VLAN ID
received on either the Ethernet or wireless link ports are
forwarded to the unit.
• A VLAN Management Tag is inserted in all management
frames generated by the unit before transmission on
either the Ethernet or wireless link port. The tag includes
the values of the VLAN ID – Voice & Management and
the VLAN Priority – Management parameters.
• A VLAN Voice Tag is inserted in all voice frames (RTP
packets) generated by the unit before transmission to the
Wireless or Ethernet port. The tag includes the values of
the VLAN ID – Voice & Management and the VLAN
Priority – Voice parameters.
If VLAN ID – Voice & Management is 65535 (No VLAN):
• Only untagged management frames received on either
Ethernet or wireless link ports are forwarded to the unit.
Action Management Port – internal (SU)
Receive from Ethernet Tagged frames, matching VID-M
Untagged frames when VID-M=65535
Receive from Wireless
(AU and SU)
Tagged frames, matching VID-M
Untagged frames when VID-M=65535
Transmit Tag Insert VID-M, PID-M