User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
2-56
BreezeACCESS Version 4.3 Operations and Administration
Manual Revision: 3.0
SNMP Traps IP Destination – Displays the current values of 3
IP addresses that are defined as the trap destinations. Allows
entering a new address for each of the 3 entries.
The default of all three SNMP Traps IP Destinations is
0.0.0.0.
SNMP Traps Community – Defines a new community string for
each of the 3 SNMP Trap IP Destination entries.
Valid strings: Up to 14 ASCII characters, case sensitive.
The default for all 3 entries is public (read-only).
Delete One Trap Address - Deletes one of the 3 IP address
entries from the list of SNMP Traps IP Destinations.
Delete All Traps Addresses - Deletes all entries from the list of
SNMP Traps IP Destinations.
Show SNMP Traps Parameters – Displays the current values of
the SNMP Traps parameters.
Show Network Management Parameters – Displays the current
values of the Network Management parameters.
Bridge Parameters (AU, SU and GU)
The Bridge Parameters sub-menu includes the following parameters
sets:
Virtual LAN (VLAN) parameters
ToS parameters
Ethernet Broadcast Filtering parameters
Other Bridging parameters
Ports Control Parameters
VLAN Parameters
VLAN Support – Defines the parameters that are related to the
VLAN-aware (Virtual LAN-aware) feature of BreezeACCESS units.
Each VLAN includes stations that can communicate with each
other, but cannot communicate with stations belonging to different
VLANs. The VLAN also provides the ability to set traffic priorities for
transmission of certain frames. The information related to the VLAN
is included in the VLAN Tag Header, which is inserted in each frame
between the MAC header and the data. VLAN implementation in
BreezeACCESS units supports frames routing by port information
(i.e. each port is connected to only one VLAN).
Send AU Alarms Traps IF-based AU Enable Traps Sending
(applicable to all AU Alarms
Traps)
Trap Unit Default