User's Manual
Table Of Contents
- BreezeACCESS Version 4.3 System Manual Revision 3.0
- Contents
- Book 1: System Description
- Contents
- Chapter 1 - Introduction
- Chapter 2 - System Components
- Chapter 3 - Specifications
- System Specifications
- BreezeACCESS II Radio Regulatory Standards
- Data Communication
- Voice/Fax (Subscriber Units with voice support)
- Telephony (Subscriber Units with voice support)
- IF Indoor – Outdoor Communication
- (SU-A/E, AU-A/E-NI, AU-A/E-BS)
- Configuration and Management
- GU-RA GPS Radio
- GU-RA to BS-GU Communication
- Environmental
- Standards Compliance, General
- Physical Specifications
- System Specifications
- Book 2: Installation
- Contents
- Chapter 1 - IF-Based Equipment
- Packing Lists
- SU-A/E Subscriber Unit
- Modular Base Station Equipment
- Standalone AU-A/ENI Access Unit
- Other Items Required for Installation
- Guidelines for Selection of Equipment Locations
- Installing the Outdoor Unit
- Installing the SU-NI and AU-NI Indoor Unit
- Installing Modular Base Station Equipment
- Installing the GU-A-BS GPS and Alarms System
- Chapter 2 - Indoor SU-R Units
- Chapter 3 - Indoor SU-I and AU-I Units
- Book 3: Commissioning
- Book 4: Operations and Administration
- Contents
- Chapter 1 - Accessing the Monitor Program
- Chapter 2 - Menus and Parameters
- Main Menu
- Info Screens Menu
- Unit Control Menu
- Basic Configuration Menu
- Site Survey Menu
- Traffic Statistics (AU and SU)
- Voice Statistics (SU with Voice Support Only)
- Per Hop Statistics (AU and SU)
- Ping Test (AU, SU and GU)
- Continuous Link Quality Display (Available in SU Only)
- MAC Address Database (Available in AU Only)
- Per-rate Counters (AU and SU)
- RSSI Display Option (AU and SU)
- ATPC Counter (AU and SU)
- AU Alarms (IF-based AU Only)
- Advanced Configuration Menu
- IP Parameters (AU, SU and GU)
- Air Interface Parameters (AU and SU)
- Network Management Parameters (AU, SU and GU)
- Bridge Parameters (AU, SU and GU)
- Performance Parameters (AU and SU)
- Service Parameters (AU and SU)
- RADIUS Parameters Menu (Subscriber Units only)
- Security Parameters (AU and SU)
- Voice Parameters (Subscriber Units with Voice Support Only)
- Dialing Parameters (Subscriber Units with Voice Support Only)
- Telephony Signals (Subscriber Units with Voice Support Only)
- Hopping Parameters (GU)
- Alarm Parameters (GU)
- Appendices
- Appendix A - Configuration Download/Upload
- Appendix B: Software Version Loading Procedure
- Appendix C: Supported MIBs and Traps
- BreezeACCESS System Object Identifiers
- brzAccessMIB
- Service Parameters
- RADIUS General Parameters
- Accounting Parameters
- RADIUS Authentication Parameters
- User Filtering Parameters
- Network Management Parameters
- Bridge Parameters
- Air Interface Parameters
- Performance Parameters
- Site Survey Parameters
- Special Operations Parameters
- Unit Control Parameters
- IP Parameters
- System Information Parameters
- Alarms Parameters
- brzPhoneMIB (applicable to SU with voice only)
- Supported Traps
- Appendix D: RSSI to dBm Conversion Table
- Appendix E: Parameters List
- Appendix F: Hopping Sequences
- Index
2-52
BreezeACCESS Version 4.3 Operations and Administration
Manual Revision: 3.0
The default value is 30.
Show ACSE Parameters – Displays the current settings of all
ACSE parameters. The display in the SU includes the ACSE
Option, which is only configurable in the AU. It also includes
the ACSE Dwell Time, which is set to 60 milliseconds.
Scanning Mode (SU only) – Defines whether to use Active or
Passive scanning. In active scanning, the SU transmits a Probe
Request upon power-up. In passive scanning, the SU searches for a
Beacon message from an AU prior to starting the
authentication/association process. This parameter is not
applicable if the ACSE Option is enabled, in which case passive
scanning is always used.
The default is Active
MAC Address Black List (AU only) - Enables to define units that are
not authorized to receive services. The AU will not provide services
to a unit whose MAC Address is included in the black list. This
feature enables to disconnect units from the services in cases such
as when the user had fraudulently succeeded to configure the unit
to values different than his subscription plan. The black list can
include up to 100 MAC Addresses.
Add MAC Address to Black List - To add a MAC Address to the
Black List.
Remove MAC Address from Black List - To remove a MAC
Address from the Black List.
Show MAC Address Black List - To display the current list of
MAC Addresses included in the black list.
Wireless Trap Threshold - Enables to define the threshold for the
wireless quality traps: The brzaccAUWirelessQualityTRAP or the
brzaccSUWirelessQualityTRAP indicate that the quality of the
wireless link has gone below or above the specified threshold.
For AU the threshold is in percents of retransmissions. For SU the
threshold is in RSSI units, indicating the quality of the received
signal. Appendix D provides information on RSSI to dBm
conversion.
Default values:
AU: 30 (%)
IF-based SUs: 93 (RSSI units)
SU-R: 48 (RSSI units)
NOTE:
When Best AU support is enabled, it is recommended to use Active Scanning.
If passive scanning is used, the SU may not hear the best AU (or the preferred
AU). The higher the number of hopping channels, the higher the probability
that the SU will not hear the best (or preferred) AU when passive scanning is
used.